O形与C形组合密封圈的力学性能对比分析

建立了 O形密封圈与C形组合密封圈的轴对称模型,分析了两种密封圈的静、动密封性能和过孔性能,并计算出了不同压力下密封圈的摩擦阻力.对比两种密封圈的性能,结果表明:O形密封圈适用于较低压力的静密封;高压静密封、压力超过15MPa时的动密封及过孔工况下,O形密封圈的使用需增加挡圈;因O形圈变形严重,局部应力较大,易发生疲劳...     

聚合物纳米孔隙增透膜制备工艺的研究

论述了聚合物纳米孔隙增透膜的制备工艺流程,分析了聚合物材料分子量、实验环境温度和湿度、溶剂挥发性等条件对纳米孔隙增透膜的影响。研究表明,聚合物材料分子量的增大、温度的降低、湿度的升高以及采用挥发性弱的溶剂都将导致增透膜孔隙尺寸的增大,孔隙越大其对光的散射损耗就会增大,所以增透膜的透过率就越低。通过大量的试验分析得出一组较理想的工艺参量:使用低分子量的聚合物材料(小于15 kg/mol),环境温度大于25℃、环境相对湿度小于30%,在采用低沸点的溶剂如四氢呋喃等措施下可有效降低增透膜散射损耗。     

Improved Initial Charging Capacity of Na-poor Na0.44MnO2 via Chemical Presodiation Strategy for Low-cost Sodium-ion Batteries

Sodium-ion batteries(SIBs)are promising for grid-scale energy storage applications due to the natural abundance and low cost of sodium.Among various Na insertion cathode materials,Na0.44MnO2 has attracted the most attention because of its cost effectiveness and structural stability.However,the low initial charge capacity for Na-poor Na0.44MnO2 hinders its practical applications.Herein,we developed a facile chemical presodiated method using sodiated biphenly to transform Na-poor Na0.44MnO2 into Na-rich Na0.66MnO2.After presodiation,the initial charge capacity of Na0.44MnO2 is greatly enhanced from 56.5 mA·h/g to 115.7 mA·h/g at 0.1 C(1 C=121 mA/g)and the excellent cycling stability(the capacity retention of 94.1%over 200 cycles at 2 C)is achieved.This presodiation strategy would open a new avenue for promoting the practical applications of Na-poor cathode materials in sodium-ion batteries.     

CS-CMC聚合物电解质膜的制备及在电生成FeO2-4中的应用

以戊二醛为交联剂,制备了壳聚糖(CS)-羧甲基纤维素(CMC)聚合物电解质膜.用电子显微镜观察其表面形貌.IR分析表明该聚合物薄膜含有COOH,NH3+官能团,具有两性离子的特征.与CS膜或CMC膜相比,该膜能稳定存在于酸碱溶液中.膜特性研究表明CS-CMC聚合物电解质膜具有离子交换和选择性渗透能力,可作为隔膜电解制备高铁酸盐.     

空心微米镍球的表面改性及微波吸附性能研究

采用特殊的化学镀方法对已制备的空心微米镍球进行表面组装, 成功地在该镍球表面包覆了一层蜂窝状包覆钴层. 通过FESEM, TEM, XRD衍射表征了该包覆镍球, 观察到均匀包覆钴层的网眼构造和密集孔隙结构. 用BET气体吸附法、同轴线法对该镍球比表面积和微波性能进行了研究. 研究表明, 蜂窝状包覆钴层提高了粒子的比表面积, 同时表面镀钴提高了镍球的复介电常数值, 从而能增加粒子对电磁波的电介质损耗, 提高粒子在微波频率范围内对电磁波的反射吸收.     

改性壳聚糖质子交换膜在隔膜电解制备FeO42-中的应用

由壳聚糖,经2%H2SO4交联处理、1%H2SO4掺杂制备壳聚糖质子交换膜.膜特性(如溶胀率、交换容量、渗透性、电解隔膜等)测试表明,该壳聚糖膜可适用于隔膜电解制备高铁酸盐.与Nafion膜相比,具有工艺简便,价格便宜等优点.     

磨料形貌及分散介质对4H碳化硅晶片研磨质量的影响研究

研磨作为4H碳化硅(4H-SiC)晶片加工的重要工序之一,对4H-SiC衬底晶圆的质量具有重要影响。本文研究了金刚石磨料形貌和分散介质对4H-SiC晶片研磨过程中材料去除速率和面型参数的影响,基于研磨过程中金刚石磨料与4H-SiC晶片表面的接触情况,推导出简易的晶片材料去除速率模型。研究结果表明,磨料形貌显著影响4H-SiC晶片的材料去除速率,材料去除速率越高,晶片的总厚度变化(TTV)越小。由于4H-SiC中C面和Si面的各向异性,4H-SiC晶片研磨过程中C面的材料去除速率高于Si面。在分散介质的影响方面：水基体系研磨液的Zeta电位绝对值较高,磨料分散均匀,水的高导热系数有利于控制研磨过程中的盘面温度;乙二醇体系研磨液的Zeta电位绝对值小,磨料易发生团聚,增大研磨过程的磨料切入深度,晶片的材料去除速率提高,晶片最大划痕深度随之增大。     

Metallocene ion pairs: A direct insight into the reaction equilibria and polymerization by 13C NMR spectroscopy

The reaction equilibria of Cp₂Ti¹³CH₃Cl and Cp₂Ti(CH₃)₂ with AlMe₃ (TMA) and/or methylaluminoxane (MAO) have been investigated by ¹³C NMR. Several adducts have been identified. A study of the ¹³C 90% enriched ethylene polymerization in an NMR tube in the presence of the above catalytic systems, in the most experimentally significant conditions, and a comparison of the NMR data with the catalytic activity have been made as well. It has been shown that: i) some species are side products, inactive for addition ethylene polymerization; ii) active cation-like species such as Cp₂TiMe⁺Cl·[AlMeO]_n- and Cp₂TiMe⁺Me·[AlMeO]_n- are formed in titanocene-MAO systems. Concerning the role of AlMe₃, contained in MAO solutions, it has been shown that: a) AlMe₃ is mainly bound to MAO; b) if some “free” AlMe₃ exists in solution it is not the actual cocatalyst in the metallocene-MAO based catalytic systems; c) the amount of AlMe₃ influences either active or inactive species.     

二维变系数反应扩散方程的紧交替方向差分格式

1 引言 在研究热传导过程、气体扩散现象和电磁场的传播等问题时,常常遇到抛物型偏微分方程。用有限差分方法研究这类问题的数值解法目前已经有了许多工作。对于二维、三维抛物方程的数值求解比较理想的方法是交替方向法。