Giant Magneto-Impedance of Co50Ni22Ga28 Alloy with High Chemical Ordering

The microstructure of CosoNi22Ga28 ribbon with the L10 structure is examined. The band-like morphology is observed. These bands with the width in a range of 40-200 nm appear along the transverse direction of the ribbon. The giant magnetoimpedance （GMI） effect in this alloy is measured. The results show that Co5oNi22Ga28 exhibits a sharp peak of the GAI effect. The maximum GAH ratio up to 360% is detected. The GMI effect measured versus temperature shows large jumps of the magnetoimpedance amplitude at the reversal martensitic transformation temperature 240℃ and Curie temperature 375℃C respectively. The jump ratios of the magnetoimpedance amplitude examined at these temperatures are about 5 and 10, respectively.     

Efficient Oxidation of Alcohols with Potassium Permanganate Adsorbed on Aluminum Silicate Reagent

A new reagent, potassium permanganate adsorbed on aluminum silicate, suitable for the oxidation of primary and secondary alcohols to the corresponding carbonyl compounds is described.     

Synthesis of highly condensed heterocycles using radical reactions

Using radical chemistry novel highly condensed heterocycles have been synthesized. The mechanism for their formation is discussed.     

Photorefractive Four-Wave Mixing Switches Utilizing Pockels Effect -Longitudinal and Lateral Switches-

We carried out detailed calculations for photorefractive wave-mixing switches based on one of three crystals with high electro-optic coefficients, namely, BaTiO₃, Strontium Barium Niobate (SBN (0.75)), and Potasium Sodium Strontium Barium Niobate (KNSBN). A comparison of results for the three crystals shows that a 0_-cut BaTiO³ crystal is suitable for a longitudinal switch and requires a voltage of about 80 for a 2-mm-thick crystal to induce sufficient phase mismatch. The electrodes must be transparent for the incident and diffracted beams. A 45_-cut SBN (0.75) crystal, however, is suitable for a lateral switch and requires a voltage of about 150 for a 1-mm-wide crystal. The electrodes do not need to be transparent.     

Ultrafast softening in InMnAs

We have used two-color time-resolved magneto-optical Kerr effect spectroscopy to manipulate and detect dynamic processes of spin/magnetic order in a ferromagnetic semiconductor InMnAs. We observed ultrafast photo-induced “softening” (i.e., transient decrease of coercivity) due to spin-polarized transient carriers. This transient softening persists only during the carrier lifetime (2 ps) and returns to its original value as soon as the carriers recombine to disappear. Our data clearly demonstrates that magnetic properties, e.g., coercivity, can be strongly and reversibly modified in an ultrafast manner. We attribute the origin of this unusual phenomenon to carrier-mediated ferromagnetic exchange interactions between Mn ions. We discuss the dependence of data on the pump polarization, pump intensity, and sample temperature. Our observation opens up new possibilities for ultrafast optical manipulation of ferromagnetic order as well as providing a new avenue for studying the dynamics of long-range collective order in strongly correlated many-body systems.     

Living polymerization of styrene initiated by mercaptan/ε‐caprolactam

The bulk polymerization of styrene initiated by ?‐caprolactam (CL) and n‐dodecyl mercaptan (RSH) has been explored. This novel polymerization system shows living characteristics. For example, the molecular weight of the resulting polymers increases with conversion, and the system has the ability to form diblock copolymers and so forth. The polymer chain end contains thiol and lactam structures, which we have investigated with Fourier transform infrared, ¹H NMR, and ¹³C NMR techniques. Electron spin resonance spectra and theoretical calculations by the Hartree–Fock methods have been used to examine the mechanism. The results reveal that the initial polymerization starts from thiol via a chain‐transfer reaction, and the propagation proceeds by the insertion of a monomer between the terminal group and the intermediate structure of lactam. Finally, the polymerization kinetics have been examined. The polymerization rate varies linearly with the concentration of CL and RSH, and this confirms the mechanism. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4976–4993, 2004     

Synthesis and characterization of new segmented polyurethanes with side‐chain,liquid‐crystalline chain extenders

Liquid‐crystalline, segmented polyurethanes with methoxy–biphenyl mesogens pendant on the chain extender were synthesized by the conventional prepolymer technique and esterification reaction. Two, side‐chain, liquid‐crystalline (SCLC) polyurethanes with mesogens having spacers of six and eight methylene units were prepared. The structures of the mesogenic units and SCLC polyurethanes were confirmed by Fourier transform infrared spectroscopy and ¹H NMR. Polymer properties were also examined by solubility tests, water uptakes, and inherent viscosity measurements. Differential scanning calorimetry studies indicated that the transition temperature of the isotropic to the liquid‐crystalline phase decreased with increasing spacer length. Wide‐angle X‐ray diffraction (WAXD) studies revealed the existence of liquid‐crystalline phases for both SCLC polyurethanes. Polarized optical microscopic investigations further confirmed the thermotropic liquid‐crystalline behaviors and nematic mesophases of both samples. Thermogravimetric analysis displayed better thermal stabilities for both SCLC polymers and indicated that the presence of mesogenic side chains may increase the thermal stability of segmented polyurethanes. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 290–302, 2004     

Performance of various activators in ethylene polymerization based on an iron(II) catalyst system

Ethylisobutylaluminoxane (EBAO) and its analogues were synthesized by a reaction between an triethylaluminum (Et₃Al)/triisobutylaluminum (i‐Bu₃Al) mixture and 4‐fluorobenzeneboronic acid, phenylboronic acid, or n‐butaneboronic acid and subsequent hydrolysis with water. They were used as cocatalysts in ethylene polymerization catalyzed by an iron complex {[(ArN?C(Me))₂C₅H₃N]FeCl₂, where Ar is 2,6‐diisopropylphenyl}. Polyethylene with a high molecular weight and a narrow molecular weight distribution was prepared with modified EBAOs, and the performance of the iron complex at high polymerization temperatures was greatly improved. The activators for the iron complex also affected the polymerization activity and the molecular weight of the resultant polyethylene. It was suggested that the stereo and electronic effects of the substitute groups of aluminoxane contributed to the improved performance of the new activators. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 1093–1099, 2004     

Novel,organosoluble, light‐colored fluorinated polyimides based on 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl or 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl

Two series of fluorinated polyimides were prepared from 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)biphenyl ( 2 ) and 2,2′‐bis(4‐amino‐2‐trifluoromethylphenoxy)‐1,1′‐binaphthyl ( 4 ) with various aromatic dianhydrides via a conventional, two‐step procedure that included a ring‐opening polyaddition to give poly(amic acid)s, followed by chemical or thermal cyclodehydration. The inherent viscosities of the polyimides ranged from 0.54 to 0.73 and 0.19 to 0.36 dL/g, respectively. All the fluorinated polyimides were soluble in many polar organic solvents, such as N,N‐dimethylacetamide and N‐methylpyrrolidone, and afforded transparent and light‐colored films via solution‐casting. These polyimides showed glass‐transition temperatures in the ranges of 222–280 and 257–351 °C by DSC, softening temperatures in the range of 264–301 °C by thermomechanical analysis, and a decomposition temperature for 10% weight loss above 520 °C both in nitrogen and air atmospheres. The polyimides had low moisture absorptions of 0.23–0.58%, low dielectric constants of 2.84–3.61 at 10 kHz, and an ultraviolet–visible absorption cutoff wavelength at 351–434 nm. Copolyimides derived from the same dianhydrides with an equimolar mixture of 4,4′‐oxydianiline and diamine 2 or 4 were also prepared and characterized. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2416–2431, 2004