Pulsed Nd:YAG laser welding of AISI 304 to AISI 420 stainless steels

The technique to weld AISI 304 stainless steel to AISI 420 stainless steel with a pulsed Nd:YAG laser has been investigated. The main objective of this study was to determine the influence of the laser beam position, with respect to the joint, on weld characteristics. Specimens were welded with the laser beam incident on the joint and moved 0.1 and 0.2 mm on either side of the joint. The joints were examined in an optical microscope for cracks, pores and to determine the weld geometry. The microstructure of the weld and the heat affected zones were observed in a scanning electron microscope. An energy dispersive spectrometer, coupled to the scanning electron microscope, was used to determine variations in (weight %) the main chemical elements across the fillet weld. Vickers microhardness testing and tensile testing were carried out to determine the mechanical properties of the weld. The results of the various tests and examinations enabled definition of the best position for the incident laser beam with respect to the joint, for welding together the two stainless steels.     

Turbulence in microfluidics: Cleanroom-free,fast, solventless,and bondless fabrication and application in high throughput liquid-liquid extraction

This paper addresses an important breakthrough in the deployment of ultra-high adhesion strength microfluidic technologies to provide turbulence at harsh flow rate conditions. This paper is only, to our knowledge, the second reporting on the generation of high flow rate-assisted turbulence in microchannels. This flow solves a crucial bottleneck in microfluidics: the generation of high throughput homogeneous mixings. We focused on the fabrication of bulky polydimethylsiloxane (PDMS) microchips (without any interfaces) rather than the laborious surface modifications that were employed in the first reporting about turbulence-assisted microfluidics. The fabrication is cleanroom-free, simple, low-cost, fast, solventless, and bondless requiring only a laboratory oven. More specifically, our method relies on the shaping of a nylon scaffold, cure of PDMS with embedded nylon, and removal of this scaffold. The scaffold was obtained by manually wrapping nylon threads. The withdrawing out of the scaffold was completed in few seconds using only a plier. Such microchannels endured flow rates of up to 60.0 mL min⁻¹ with a strikingly low elastic deformation. The importance in producing turbulence into microscale channels was successfully shown in liquid-liquid extractions. The great energy dissipation rate relative to the turbulence created high throughput and efficient extractions in microfluidics for the first time. The residence time was only 0.01 s at 25.0 mL min⁻¹ (total flow rate of the immiscible phases). In addition, the partition coefficient determined in a single run was similar to that obtained by the conventional batch shake-flask method that was realized in triplicate.     

Solid-phase extraction of triazole fungicides from water samples using disks impregnated with carbon nanotubes followed by GC-MS analysis

Triazole fungicides are pesticides widely employed in the cultivation of fruits, vegetables and grains. However, their ability to change the steroid hormone biosynthesis may result in endocrine complications for mammals, as well as changes in cholesterol and triglyceride levels and hepatotoxicity. The analysis of the triazole fungicides in superficial waters is important in order to monitor the risk for the biota. However, the use of efficient extraction procedures has been necessary in order to concentrate these pesticides before the analysis. In-disk solid-phase extraction (SPE) can be highlighted as a potential pre-concentration technique, mainly because the possibility to extract the analytes from a large sample volume, increasing the method detectability. Carbon nanotubes (CNTs) have been often used as solid extraction phase due to their high sorption capacity, surface area and internal volume, as well as mechanical, chemical and thermal stability. In this paper, we proposed the preparation of a new SPE disk impregnated with CNTs for the extraction of triazole fungicides from environmental water samples. The disks were obtained by acid corrosion of a cellulose membrane followed by its impregnation with CNTs. The developed method was validated for the analysis of triadimenol, tebuconazole and epoxiconazole, according to international validation protocols. The limits of quantification obtained for triadimenol, tebuconazole and epoxiconazole were 0.1, 0.1 and 0.05 µg L^?1, respectively. The linearity ranged from 0.05 to 10.00 µg L^?1 for epoxiconazole and from 0.1 to 10.00 µg L^?1 for triadimenol and tebuconazole, with correlation coefficients higher than 0.999 for all of them. The precisions, expressed as relative standard deviation, were lower than 12%. The accuracies were within ?12.07% to 17.7% (expressed as relative error).     

Geometric Properties of Self-Shrinkers in Cylinder Shrinking Ricci Solitons

In this paper, we prove some spectral properties of the drifted Laplacian of self-shrinkers properly immersed in gradient shrinking Ricci solitons. Then we use these results to prove some geometric properties of self-shrinkers. For example, we describe a collection of domains in the ambient space that cannot contain self-shrinkers.