A study of corrosion on a rotating iron disk electrode

Corrosion of iron in slightly acidified sodium sulphate solutions (mainly pH 4.5) in the open air was studied with a rotating disk electrode method at room temperature.Microscopic observations of corroded iron disk surfaces in the pH 4.5 solution revealed that iron initially corrodes locally with the formation of round pits of 10–30 μm in diameter and of(0.6–1.3) × 10³ in number per apparent square centimetre followed by the U-shaped brown protective wall formation of precipitates (rust) outside the pits. Each protective wall is formed along the lines of flow of the solution adjacent to the iron surface and each pit is located near the upstream end of the wall. Steady state of corrosion sets in when the parts of surface area surrounded by the wall are completely covered with a microscopically non-porous rust film.The amount of iron in the rust film and the total amount of corrosion of iron including that in the film increase parabolically with the increase in the time of immersion. The amount of iron in the film increases in proportion to the total amount of corrosion independently of the speed of rotation of the disk electrode even in the steady state.The fraction of area of iron surface not covered with the film decreases with time and reaches a certain fixed value in the steady state: the value is smaller at higher rotational speed. The corrosion rate is proportional to the uncovered area, as the corrosion is near the steady state. The pH of the bulk solution increases as corrosion progresses.The corrosion rate of iron can be well interpreted by assuming that the rate is controlled by the diffusion of oxygen from the bulk solution to the surface of iron and that the rust film on iron impedes the diffusion of oxygen.     

Polymerization of methyl methacrylate initiated by tri-n-butylborane–organic halide systems

The polymerization of methyl methacrylate (MMA) initiated by tri-n-butylborane (TBB) was studied in the presence of various organic halides (R′X). It was found that R′X accelerated the polymerization of MMA. Aliphatic halides were more effective than aromatic halides. Cocatalytic effects of butyl halides decreased in the order: n -BuI > n -BuBr > n -BuCl; n -BuBr ? sec-BuBr > i-BuBr > tert-BuBr. In the polymerization of MMA by TBB- n -BuI, the initial rate of polymerization was found to be proportional to the concentration of MMA and to the square root of the concentration of TBB-n-BuI. The apparent activation energy was 5.3 kcal/mole. From this and other results, it was assumed that the polymerization of MMA by this initiator system proceeds by a radical mechanism via a weak complex between TBB and R′X; alkyl radicals are formed by the interaction of R′X with TBB. The TBB–R′X system can initiate the polymerization of MMA and AN, but is ineffective in the polymerization of styrene.     

3-Aroylmethyl derivatives of 2(1H)quinoxalinone and 2H-l,4-benzoxazin-2-ones existing in the enamine form

Seventeen derivatives of 2(1H)quinoxalinone and 2H-l,4-benzoxazin-2-one have been synthesized for structural study. All of the compounds having a substituted phenacyl, isonicotinoylmethyl, or 2-furoylmethyl side chain are shown to exist in the enamine form with an internal chelation both in the crystalline and solution states as evidenced by the ir and pmr spectra, respectively. In the gas phase, however, o-hydroxyphenacyl derivatives can exist in another type of intramolecularly hydrogen-bonded form which is supported by their mass spectra.     

Radiation-induced heterogeneous polymerization of acrylamide in acetone and acetone–water mixtures

The effects of temperature, dose rate, and monomer concentration on the heterogeneous polymerization of acrylamide in acetone–water mixtures have been studied. Heterogeneous polymerization takes place in mixtures containing less than 60 vol-% water. The polymerization is steady in acetone and nonsteady in acetone an nonsteady in mixtures containing 10–50 vol-% water. The average rate of polymerization is highest in mixtures with about 20 vol-% water. Polymer molecular weight increases with the increasing water content in range 0–10 vol-% and does not change in the range of 30–70 vol-% water. For the polymerization in acetone and an acetone–water 60/40 mixture the activation energies are 2.3 and ?1.8 kcal/mole, the dose rate exponents of rate are 0.78 and 0.52, and the monomer concentration exponents of rate are 0.5 and 1.6, respectively. The polymer molecular weight increases with decreasing dose rate, decreasing temperature, and increasing monomer concentration. These results are discussed in connection with the mechanism of heterogeneous polymerization and the solvent effect.     

Effects of trivalent phosphorus compounds on vinyl polymerizations—VII. A nonstationary state radical polymerization of methylmethacrylate in the presence of phenyldichlorophosphine

In the radical polymerization of methylmethacrylate in the presence of p-phenyldichlorophosphine, the initial rate and degree of polymerization increased with polymerization time. They first decreased with increase in the phosphine concentration but increased with further increase in the phosphine concentration. Termination was first order with respect to the initiator. The degree of polymerization was independent of the initiator concentration, but dependent on the conversion. The polymer contained no phosphorus units regardless of the phosphine concentration. The ESR spectra of system showed existence of a phosphorus radical. In order to explain these characteristics of the polymerization, it is proposed that there may be a nonstationary state in which the polymer radicals are regenerated during the polymerization from the phosphoranyl radicals.     

Replacement of the phosphorodiester linkages of RNA with guanidinium linkages: the solid-phase synthesis of ribonucleic guanidine

[reaction: see text] Replacement of the negatively charged phosphodiester linkages of RNA with positively charged guanidinium linkages provides the polycationic ribonucleic guanidine (RNG). RNG is anticipated to bind strongly to target DNA/RNA through the specific interactions of nucleobases and the attractive electrostatic interactions of backbones. Preparation of building blocks and the solid-phase synthesis of RNG are reported. Both trimeric and pentameric uridyl RNG have been synthesized.     

A novel scheme of heterogeneous polymerization of ethylene

The heterogeneous polymerization of ethylene initiated by radiation in tert-butyl alcohol was studied. The polymerization was carried out in a 100-ml reactor at 25–100°C and pressures of 200–300 kg/cm² in the presence of 50 ml of tert-butyl alcohol containing 7 wt-% water. The amounts of polymerized monomer, the average molecular weight of polymer formed, and the molecular weight distribution of polymer were measured at various stages of reaction and at various temperatures. The molecular weight distribution was found to be very much dependent on the reaction time and temperature. For the polymer formed at 50–60°C in the very early stages of reaction, the molecular weight distribution is unimodal, and in the intermediate stage a shoulder appears at a molecular weight higher than the first peak which increases as the polymerization proceeds; eventually a bimodal curve is formed. The bimodal distribution curves were analyzed to determine the fractions and average molecular weights of the each peak. On the basis of these data for the molecular weight distribution and kinetic behavior, a new scheme for the heterogeneous polymerization is proposed which indicates that the polymerization proceeds via propagating radicals in two different physical states, namely, loose and rigid states.     

Emulsifier-free emulsion polymerization of tetrafluoroethylene by radiation. I. Effects of reaction conditions on the polymerization rate and polymer molecular weight

The radiation-induced emulsifier-free emulsion polymerization of tetrafluoroethylene was carried out at an initial pressure of 2–25 kg/cm², temperature of 30–110°C, and under a dose rate of 0.57 × 10⁴?3.0 × 10⁴ rad/hr. The rate of polymerization was shown to be proportional to 1.0 and 1.3 powers of the dose rate and initial pressure, respectively, and is maximal at about 70°C. The molecular weight of polytetrafluoroethylene (PTFE) lies in the range of 10⁵?10⁶, increases with reaction time in the early stage of polymerization, and is maximal at 70°C but is almost independent of the dose rate. An interesting discovery is that PTFE, a hydrophobic polymer, forms as a stable latex in the absence of emulsifier. When PTFE latex coagulates during polymerization under certain conditions, the polymerization rate decreases, probably because polymerization proceeds mainly on the polymer particle surface. The observed rate acceleration and successive increase in polymer molecular weight may be due to slow termination of propagating radicals in the rigid PTFE particles.