Influence of molecular weight upon drag reduction by polymers

Summary Drag reduction measurements have been made with samples of polyethyleneoxide and polyacrylamide with relatively narrow molecular weight distributions obtained by fractionation of commercial polymers. Relationships between the polymer molecular weight and the concentration required to give the same drag reduction have been determined. The influence of polymer degradation upon these relationships has been investigated.Molecular weight distributions of commercial polymers have been determined and their influence upon the drag-reducing properties is noted.The influence of wall shear stress has been investigated over the range 1.0 × 10² - 4.5 × 10³ dyn/cm². The results with unfractionated polymers were found to be consistent with other results in the literature.     

Measurement of rotating flows using PIV and image derotation

This paper describes the use of a rotating all-mirror image derotator system, high-speed video and particle image velocimetry (PIV) to visualise and quantitatively examine the flow patterns between the blades of a centrifugal impeller. The flow field relative to the moving centrifugal impeller is presented. Published online: 13 December 2002     

Influence of narrow starter notches on the initial crack growth resistance curve of ceramics

In experimental R-curve investigations crack development usually starts from notches. The validity of R-curves depends on the size of the notch root radius. This influence is completely ignored in most cases. In this theoretical study it is shown how the notch radius affects the formally computed crack resistance curve. First, the influence of the notch radius on the starting point of the R-curve, the so-called crack-tip toughness K _I0, will be addressed. Then, the effect of the notch on the shielding stress intensity factor will be discussed, and, finally, the influence on T-stress and the consequences on local path stability will be shown.     

The contact stress in a bolted joint with a threaded bolt

The contact stress of a bolted joint, in which a clamped part was fastened to a body with a threaded bolt, was measured using sensitive pins, sensitive films and ultrasonic waves. The contact stress distribution was analyzed as a contact problem by an axisymmetrical theory of elasticity. Numerical calculations were performed. The experimental results were in fairly good agreement with the analytical results.Paper was presented at the 1992 SEM International Congress held in Las Vegas on June 9, 1992.     

Heat transfer during gas hydrate formation in gas-liquid slug flow

A model of heat transfer during gas hydrate formation at a gas-liquid interface in gas-liquid slug flow is suggested. Under the assumption of perfect mixing in liquid plugs, the recurrent relations for temperature in then-th liquid plug and heat and mass fluxes from then-th gas slug are derived. Total mass and heat fluxes in gas-liquid slug flow during gas hydrate formation are determined.     

On shapes of body waves in periodically inhomogeneous, magnetostrictive, dielectric materials

The shapes of shear body waves in periodically inhomogeneous, magnetostrictive, dielectric media are studied with emphasis on the partial (elastic and magnetostrictive) wave motions coupled to produce magnetoelastic waves __________ Translated from Prikladnaya Mekhanika, Vol. 42, No. 7, pp. 57–63, July 2006.     

On the solution of plane boundary-value problems of elasticity in a rectangle

An algorithm for solving plane boundary-value problems of elasticity for a rectangular domain is expounded. The algorithm is based on a complex-valued representation of the general solution to the differential equations of the plane problem and on the use of Lagrange polynomials to satisfy the boundary conditions. The algorithm can quite easily be implemented in a computer program. This is probably the simplest way of solving boundary-value problems of this class __________ Translated from Prikladnaya Mekhanika, Vol. 42, No. 1, pp. 97–102, January 2006.     

Cell model of nonisothermal gas absorption in gas-liquid bubbly media

A model for combined mass and heat transfer during nonisothermal gas absorption in a two-phase gasliquid bubbly medium with a high gas content and/or large times of gas-liquid contact is suggested. Diffusion and thermal interactions between bubbles is taken into account in the approximation of a cellular model of a bubbly medium whereby a bubbly medium is viewed as a periodic structure consisting of identical spherical cells with periodic boundary conditions at a cell boundary. Distribution of concentration of dissolved gas, temperature distribution in liquid and coefficients of mass and heat transfer during nonisothermal absorption of a soluble pure gas from a bubble by liquid are determined. In the limiting case of absorption without heat release the derived formulas recover the expressions for isothermal absorption.