Versatile high-performance liquid chromatographic computer system for solvent delivery, gradient control and data acquisition using the Commodore 64 personal computer

An interface for a high-performance liquid chromatographic system based on the Commodore 64 personal computer has been designed as an alternative to the expensive and somewhat inflexible solvent programmers and data acquisition systems offered by commercial manufacturers. The system consists of the Commodore 64 with a single disk drive and monitor, and an interface that directly controls the flow-rates of two Waters pumps for solvent delivery in either isocratic or gradient mode, as well as analog-to-digital conversion of chromatographic data and either graphic data output to a dot-matrix printer or digital-to-analog conversion for output to a chart recorder. The interface permits computer-controlled flow-rates of up to 10.0 ml/min, with an accuracy of 0.0047 ml/min at flow-rates of 4.1 ml/min and an accuracy of 0.03 ml/min at flow-rates of 10 ml/min. The software for data analysis permits tabulation of elution times and areas for the peaks in a chromatogram with an option for baseline correction. The data are stored on floppy disks together with information pertinent to the chromatogram (flow-rate, solvent composition, etc.).     

Manganese(III) acetate mediated synthesis of 3-trifluoroacetyl-4,5-dihydrofurans and 3-(dihydrofuran-2(3H)-ylidene)-1,1,1-trifluoroacetones by free radical cyclization. Part 1

2-Trifluoroacetyl-4,5-dihydrofurans were obtained by manganese(III) acetate mediated radical cyclization of trifluoromethyl-1,3-dicarbonyl compounds (1a-c) with conjugated alkenes (2a-h). The reaction of 1,1,1-trifluoropentane-2,4-dione (1a) with propenylbenzene and 1,1-diphenyl-1-butene surprisingly yielded 3-(dihydrofuran-2(3H)-ylidene)-1,1,1-trifluoroacetones besides 3-trifluoroacetyl-4,5-dihydrofurans.     

Effects of temperature and sodium carboxylate additives on mineralization of calcium oxalate in silica gel systems

Urolithiasis remains a major medical problem in China, especially in Guangdong Province in the southest of China[1]. A survey in Shenzhen city, the most southern city in China, showed the incidence of renal calculus was 4.87%, being 6.12% in the males and 4.07% in the females[2]. The prevalence of renal calculus has been more as the age advances and in the male population and so was in the less-educated population. The recurrence rate is more than 80%, with a moderate improvement by conventi…     

Preparation of epitaxial La0.6Ca0.4Mn1−xFexO3 (x = 0, 0.2) thin films: Variation of the oxygen content

Perovskite thin films with a nominal composition of La_0.6Ca_0.4Mn_1−xFe_xO₃ (x = 0, 0.2) were deposited by pulsed reactive crossed beam laser ablation. The film properties, such as electrical conductivity and magnetoresistance are studied as a function of the oxygen content and substrate type. The oxygen content of the thin films was determined by Rutherford Backscattering and controlled by varying the background gas pressure, pressure of the gas pulse and by using alternatively O₂ and N₂O as the gas pulse.

LaAlO₃ and SrTiO₃ were used as substrates at deposition temperature of 650 °C. The grown films were analyzed by X-ray diffraction in order to optimize the growth conditions, i.e. to obtain epitaxial thin films. Thin films doped with 20% Fe were grown under the same experimental conditions as the undoped LCMO films and the effect of the doping on the structural and transport properties of the thin films has been investigated.

The temperature of the metal–insulator transition was measured as a function of the oxygen content and substrate type.     

Hydrogen-induced metal-oxide interaction studied on noble metal model catalysts

Summary The effect of hydrogen reduction on the structure and catalytic properties of “thin film”and “inverse”model systems for supported metal catalysts is discussed. Thin film model catalysts were obtained by epitaxial growth of Pt and Rh nanoparticles on NaCl(001), which were coated with amorphous or crystalline supports of alumina, silica, titania, ceria and vanadia. Structural and morphological changes upon hydrogen reduction between 473 and 973 K were examined by high resolution electron microscopy. Metal-oxide interaction sets in at a specific reduction temperature and is characterized by an initial “wetting”stage, followed by alloy formation at increasing temperature, in the order VO_x< TiO_x< SiO₂< CeO_x< Al₂O₃. “Inverse”model systems were prepared by deposition of oxides on a metal substrate, e.g. VO_x/Rh and VO_x/Pd. Reduction of inverse systems at elevated temperature induces subsurface alloy formation. In contrast to common bimetallic surfaces, the stable subsurface alloys of V/Rh and V/Pd have a purely noble metal-terminated surface, with V positioned in near-surface layers. The uniform composition of the metallic surface layer excludes catalytic ensemble effects in favor of ligand effects. Activity and selectivity, e.g. for CO and CO₂methanation and for partial oxidation of ethene, are mainly controlled by the temperature of annealing or reduction. Reduction above 573 K turned out to be beneficial for the catalytic activity of the subsurface alloys, but not for the corresponding thin film systems which tend to deactivate viaparticle encapsulation.</o:p>     

Amino acid analysis by using comprehensive two-dimensional gas chromatography

The separation characteristics of alkylchloroformate-derivatised amino acids (AAs) by using comprehensive two-dimensional gas chromatography (GC×GC) is reported. The use of a low-polarity/polar column set did not provide as good a separation performance as that achieved with a polar/non-polar column set, where the latter appeared to provide less correlation over the separation space. The degree of component correlation in each column set was estimated by using the correlation coefficient (r²; for ¹t_R and ²t_R data) with the low-polarity/polar and polar/low-polarity sets returning correlation coefficients of 0.86, and 0.00 respectively, under the respective conditions employed for the experiments. The 1.5-m non-polar ²D column (0.1-mm ID; 0.1-m film thickness) gave peak halfwidths of the order of 50–80 ms. Linearity of detection was good, over a three order of magnitude concentration range, with typical lower detection limit of ca. 0.01 mg L^–1, compared with 0.5 mg L^–1 for normal GC operation with splitless injection. The method was demonstrated for analysis of AAs in a range of food and beverage products, including wine, beer and honey. The major AA in these samples was proline. The Heineken beer sample had a relatively more complex and more abundant AA content compared with the other beer sample. The wine and honey samples also gave a range of AA compounds. Repetition of the sample preparation/analysis procedure for the honey sample gave acceptable reproducibility for individual AAs.     

Determination of arsenic species and arsenosugars in marine samples by HPLC–ICP–MS

Arsenic-speciation analysis in marine samples was performed by high-pressure liquid chromatography (HPLC) with ICP–MS detection. Separation of eight arsenic species—As^III, MMA, DMA, As^V, AB, TMAO, AC and TeMAs⁺—was achieved on a C₁₈ column with isocratic elution (pH 3.0), under which conditions As^III and MMA co-eluted. The entire separation was accomplished in 15 min. The HPLC–ICP–MS detection limits for the eight arsenic species were in the range 0.03–0.23 μg L⁻¹ based on 3σ for the blank response (n=5). The precision was calculated to be 2.4–8.0% (RSD) for the eight species. The method was successfully applied to several marine samples, e.g. oysters, fish, shrimps, and marine algae. Low-power microwave digestion was employed for extraction of arsenic from seafood products; ultrasonic extraction was employed for the extraction of arsenic from seaweeds. Separation of arsenosugars was achieved on an anion-exchange column. Concentrations of arsenosugars 2, 3, and 4 in marine algae were in the range 0.18–9.59 μg g⁻¹. This paper was presented at the European Winter Conference 2005     

Investigation of a cylindrical chemosorptive denuder for sampling and phase separation of toluene diisocyanate aerosols

A cylindrical chemosorptive denuder in series with a glass fibre filter has been evaluated for sampling toluene diisocyanate (TDI) aerosols. The sampler is designed for measuring personal exposure to diisocyanates. Several denuder coatings and derivatising reagents were investigated. Dimethylpolysiloxane (SE-30) and 5% phenyl dimethylpolysiloxane (SE-54) with either dibutylamine (DBA) or dipentylamine (DPeA) as derivatising reagents yielded the lowest vapour breakthrough (the amount (%) of the vapour that passes through the denuder), close to values predicted by theory. Immobilisation of the SE-30 denuder coating by in-situ cross-linking yielded comparable results. With an SE-30/DBA-coated denuder operating within an airflow range of 100–500 mL min^–1, the phase separation was shown to be consistent with theoretical predictions derived by use of the Gormley–Kennedy equation. This provides a means of calculating the vapour breakthrough and correcting experimentally obtained values with regard to vapour–particulate phase distribution, suggesting that the denuder can provide accurate phase-distribution measurements. The SE-30/DBA denuder can be used over a concentration range spanning nearly six orders of magnitude. Its capacity is sufficient to perform 15-min exposure measurements of a TDI aerosol with air concentrations as high as 1,700 g m^–3, 40 times higher than the Swedish occupational exposure limit (OEL). At the other end of the range, the estimated limit of detection (LOD) was less than 2 ng m^–3 for both the vapour and the aerosol phases when LC–ESI–MS–MS was used for chemical analysis.Electronic Supplementary Material Supplementary material for this article is available at     

Isolation of selenium organic species from antarctic krill after enzymatic hydrolysis

Total selenium content and its distribution in the soluble and insoluble protein-bound fractions obtained after aqueous extraction of antarctic krill samples were determined. About 26% of the total selenium (2.4 g g^–1 dry weight) was found in the supernatant; the rest was in the pellet. Isolation of low molecular selenium-containing fractions was also performed by enzymatic digestion of the protein, followed by size-exclusion chromatography in conjunction with atomic absorption spectrometry. From the applied various proteinases (pronase E, subtilisin Carlsberg, trypsin, chymotrypsin, proteinase and proteinase N from Bacillus subtilis and Novo 0.6 MPX enzyme), the treatment with pronase E led to best recovery of selenium. About 96% of the total Se was found in the hydrolysate, mainly in low molecular weight fractions. Eighty percent of the Se species were in fractions with molecular weights in the range of amino acids and short peptides. High-performance liquid chromatography/inductively coupled plasma mass spectrometry (HPLC-ICP-MS) allowed the identification of selenomethionine and the assumption that selenocystine or its derivatives were the main species in these fractions.