Germanane (GeH), a germanium analogue of graphane, has recently attracted considerable interest because its remarkable combination of properties makes it an extremely suitable candidate to be used as 2D material for field effect devices, photovoltaics, and photocatalysis. Up to now, the synthesis of GeH has been conducted by substituting Ca by H in a β‐CaGe2 layered Zintl phase through topochemical deintercalation in aqueous HCl. This reaction is generally slow and takes place over 6 to 14 days. The new and facile protocol presented here allows to synthesize GeH at room temperature in a significantly shorter time (a few minutes), which renders this method highly attractive for technological applications. The GeH produced with this method is highly pure and has a band gap (Eg) close to 1.4 eV, a lower value than that reported for germanane synthesized using HCl, which is promising for incorporation of GeH in solar cells. 相似文献
A new way to fabricate monodisperse polymer particles in a microfluidic device without UV‐light and without the need for high temperatures is described in this article. By applying an activator regeneration by electron transfer ‐ atom transfer radical polymerization (ARGET‐ATRP) initiator system in a co‐capillary microfluidic setup and by separating the monomer mixture in an initiator and a catalyst phase, a fast polymerization of the droplets at low temperature without premature curing and thus clogging of the capillaries can be achieved. The influence of the flow rates on the particle sizes and their polydispersity as well as the controlled character of the polymerization are investigated. The particle size is well adjustable, but the reaction is not controlled due to the high radical concentration needed for rapid polymerization. In addition, particles with incorporated UV‐dyes are produced as a proof of concept at low temperature.
An investigation into the rapid detection of mycotoxin-producing fungi on corn by two mid-infrared spectroscopic techniques was undertaken. Corn samples from a single genotype (RWA2, blanks, and contaminated with Fusarium graminearum) were ground, sieved and, after appropriate sample preparation, subjected to mid-infrared spectroscopy using two different accessories (diffuse reflection and attenuated total reflection). The measured spectra were evaluated with principal component analysis (PCA) and the blank and contaminated samples were classified by cluster analysis. Reference data for fungal metabolites were obtained with conventional methods. After extraction and clean-up, each sample was analyzed for the toxin deoxynivalenol (DON) by gas chromatography with electron capture detection (GC-ECD) and ergosterol (a parameter for the total fungal biomass) by high-performance liquid chromatography with diode array detection (HPLC-DAD). The concentration ranges for contaminated samples were 880–3600 g/kg for ergosterol and 300–2600 g/kg for DON. Classification efficiency was 100% for ATR spectra. DR spectra did not show as obvious a clustering of contaminated and blank samples. Results and trends were also observed in single spectra plots. Quantification using a PLS1 regression algorithm showed good correlation with DON reference data, but a rather high standard error of prediction (SEP) with 600 g/kg (DR) and 490 g/kg (ATR), respectively, for ergosterol. Comparing measurement procedures and results showed advantages for the ATR technique, mainly owing to its ease of use and the easier interpretation of results that were better with respect to classification and quantification. 相似文献
The effect of chloride ion concentration and pH of solution on the corrosion behavior of aluminum alloy AA7075 coated with
phenyltrimethoxysilane (PTMS) immersed in aqueous solutions of NaCl is reported. Potentiodynamic polarization, linear polarization,
open circuit potential, and weight loss measurements were performed. The surface of samples was examined using SEM and optical
microscopy. Elemental characterization of the coating by secondary ion mass spectrometry indicates an intermediate layer between
coating and aluminum alloy surface. The corrosion behavior of the aluminum alloy AA7075 depends on chloride concentration
and pH of solution. In acidic or neutral solutions, general and pitting corrosion occur simultaneously. On the contrary, exposure
to alkaline solutions results in general corrosion only. Results further reveal that aluminum alloy AA7075 is susceptible
to pitting corrosion in all chloride solutions with concentrations between 0.05 M and 2 M NaCl; an increase in the chloride
concentration slightly shifted both the pitting and corrosion potentials to more active values. Linear polarization resistance
measurements show a substantially improved corrosion resistance value in case of samples coated with PTMS as compared to uncoated
samples in both neutral (pH = 7), acidic (pH = 0.85 and 3), and alkaline chloride solutions (pH = 10 and 12.85). The higher
corrosion resistance of the aluminum alloy coated with PTMS can be attributed to the hydrophobic coating which acts as a barrier
and prevents chloride ion penetration and subsequent reaction with the aluminum alloy. 相似文献
X-ray spectroscopy studies of potassium intercalated metal-free phthalocyanine multilayers adsorbed on Al(110) have been undertaken. Photoelectron spectroscopy measurements show the presence of several charge states of the molecules upon K intercalation, due to a charge transfer from the alkali. In addition, the comparison of valence band photoemission spectra with the density functional theory calculations of the density of states of the H(2)Pc(-) anion indicates a filling of the formerly lowest unoccupied molecular orbital by charge transfer from the alkali. This is further confirmed by x-ray absorption spectroscopy (XAS) studies, which show a decreased density of unoccupied states. XAS measurements in different experimental geometries reveal that the molecules in the pristine film are standing upright on the surface or are only slightly tilted away from the surface normal but upon K intercalation, the molecular orientation is changed in that the tilt angle of the molecules increases. 相似文献
Until now, the potential effects of titanium dioxide (TiO2) nanoparticles on endothelial cells are not well understood, despite their already wide usage. Therefore, the present work characterizes six TiO2 nanoparticle samples in the size range of 19 × 17 to 87 × 13 nm, which are commonly present in sun protection agents with respect to their physicochemical properties (size, shape, ζ-potential, agglomeration, sedimentation, surface coating, and surface area), their interactions with serum proteins and biological impact on human microvascular endothelial cells (relative cellular dehydrogenase activity, adenosine triphosphate content, and monocyte chemoattractant protein-1 release). We observed no association of nanoparticle morphology with the agglomeration and sedimentation behavior and no variations of the ζ-potential (?14 to ?19 mV) in dependence on the surface coating. In general, the impact on endothelial cells was low and only detectable at concentrations of 100 μg/ml. Particles containing a rutile core and having rod-like shape had a stronger effect on cell metabolism than those with anatase core and elliptical shape (relative cellular dehydrogenase activity after 72 h: 60 vs. 90 %). Besides the morphology, the nanoparticle shell constitution was found to influence the metabolic activity of the cells. Upon cellular uptake, the nanoparticles were localized perinuclearly. Considering that in the in vivo situation endothelial cells would come in contact with considerably lower nanoparticle amounts than the lowest-observable adverse effects level (100 μg/ml), TiO2 nanoparticles can be considered as rather harmless to humans under the investigated conditions. 相似文献