A dried blood spot assay with HPLC–MS/MS for the determination of larotrectinib in mouse blood and its application to a pharmacokinetic study

Larotrectinib is a first-generation tropomyosin kinase inhibitor, approved for the treatment of solid tumors. In this paper, we present a validated dried blood spot (DBS) method for the quantitation of larotrectinib from mouse blood using HPLC–MS/MS, which was operated under multiple reaction monitoring mode. To the DBS disc cards, acidified methanol enriched with internal standard (IS; enasidenib) was added and extracted using tert-butyl methyl ether as an extraction solvent with sonication. Chromatographic separation of larotrectinib and the IS was achieved on an Atlantis dC₁₈ column using 10 mm ammonium formate–acetonitrile (30:70, v/v) delivered at a flow-rate of 0.80 ml/min. Under these optimized conditions, the retention times of larotrectinib and the IS were ~0.93 and 1.37 min, respectively. The total run time was 2.50 min. Larotrectinib and the IS were analyzed using positive ion scan mode and parent–daughter mass to charge ion (m/z) transitions of 429.1 → 342.1 and 474.1 → 267.1, respectively, were used for the quantitation. The calibration range was 1.06–5,080 ng/ml. No matrix effect or carryover was observed. Hematocrit did not influence DBS larotrectinib concentrations. All of the validation parameters met the acceptance criteria. The applicability of the validated method was shown in a mouse pharmacokinetic study.     

Formation of porous polymer morphology by microsyneresis during divinylbenzene polymerization

This article describes the investigation of the importance of various reaction conditions on microsyneretic pore formation during polymerization of divinylbenzene (DVB) under so‐called “solvothermal” conditions. To induce microsyneretic pore formation, the most important parameter is an unusually high dilution of monomers with a “good” porogen solvating the polymer chains. High dilution and solvation of the growing poly(DVB) chains promote the prolongation of the polymer chains rather than their interconnection by crosslinking. Consequently, when the polymer gel density reaches the point where syneresis starts, the polymer network is geometrically too extensive to be broken up into precipitating entities and, instead, porogen droplets are formed within the continuous polymer gel. The pore geometry created by microsyneresis offers high surface area in wide mesopores and hence, high capacity for supporting functional groups or reactions with much better accessibility than narrow pores between polymer microspheres produced by macrosyneresis in conventional styrenic polymer supports. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 774–781     

Fatigue life enhancement by irradiation of 12Cr1MoV steel with a Zr<Superscript>+</Superscript> ion beam. Mesoscale deformation and fracture

The structure and properties of 12Cr1MoV steel irradiated with a zirconium ion beam were studied by optical microscopy, scanning electron microscopy, and micro- and nanoindentation. It is shown that the modification covers the entire cross-section of the irradiated specimens to a depth of 1 mm. The data on irradiation-induced structural changes are used to interpret the changes in mechanical properties of the irradiated specimens under static and cyclic loading. Particular attention is given to analysis of strain estimation by the digital image correlation method.     

Microtextures Induced by Nanosecond Laser on Ni–Co Alloy Coatings

Ni–Co alloys have a wide range of applications in various fields owning to their excellent physical, chemical, and mechanical properties. In this paper, we prepare Ni–Co alloy coatings on 316L stain steel surfaces by electroplating. We present a novel approach utilizing a nanosecond laser to induce microtextures on Ni–Co alloy coatings. We study experimentally the effects of laser power and scanning rate on the surface morphologies of Ni–Co alloy coatings. The results indicate that the shape and size of induced microtextures can be controlled by the laser power and scanning rate. The size of grains increases with increase in the work current of the laser (WCL) at a certain scanning rate. With the WCL constant, the size of grains decreases with increase in scanning rate while their average height increases. It is a simple and easily-controlled method for the fabrication of microstructures on Ni–Co alloy coatings, which has promising applications in investigations of the properties of microtextured surfaces, such as friction, adhesion, and wetting.