单载流子传输的双异质结光敏晶体管探测器的研究

基于器件仿真器Atlas, 建立了InP/InGaAsP单向载流子传输的双异质结光敏晶体管(UTC-DHPT)的二维模型, 分析讨论了器件性能与外延结构参数的关系. 设计出同时具有高响应度(≥17.93 A/W)和高特征频率(≥121.68 GHz)的UTC-DHPT, 缓解了传统的异质结光敏晶体管光电探测器中探测效率和工作速度的矛盾. 关键词： 单向载流子 光敏晶体管 电流放大倍数 响应度     

High resolution dynamic cardiac MRI using partial separability of spatiotemporal signals with a novel sampling scheme

The partial separability (PS) of spatiotemporal signals has been exploited to accelerate dynamic cardiac MRI by sampling two datasets (training and imaging datasets) without breath-holding or ECG triggering. According to the theory of partially separable functions, the wider the range of spatial frequency components covered by the training dataset, the more accurate the temporal constraint imposed by the PS model. Therefore, it is necessary to develop a new sampling scheme for the PS model in order to cover a wider range of spatial frequency components. In this paper, we propose the use of radial sampling trajectories for collecting the training dataset and Cartesian sampling trajectories for collecting the imaging dataset. In vivo high resolution cardiac MRI experiments demonstrate that the proposed data sampling scheme can significantly improve the image quality. The image quality using the PS model with the proposed sampling scheme is comparable to that of a commercial method using retrospective cardiac gating and breath-holding. The success of this study demonstrates great potential for high-quality, high resolution dynamic cardiac MRI without ECG gating or breath-holding through use of the PS model and the novel data sampling scheme.     

TiO2 Nanotube Array/Monolayer Graphene Film Schottky Junction Ultraviolet Light Photodetectors

Schottky junctions made from a titanium dioxide nanotube (TiO₂NT) array in contact with a monolayer graphene (MLG) film are fabricated and utilized for UV light detection. The TiO₂NT array is synthesized by the anodization and the MLG through a simple chemical vapor deposition process. Photoconductive analysis shows that the fabricated Schottky junction photodetector (PD) is sensitive to UV light illumination with good stability and reproducibility. The corresponding responsivity (R), photoconductive gain (G), and detectivity (D*) are calculated to be 15 A W^?1, 51, and 1.5 × 10¹² cm Hz^1/2 W^?1, respectively. It is observed that the fabricated PD exhibits spectral sensitivity and a simple power‐law dependence on light intensity. Moreover, the height of the Schottky junction diode is derived to be 0.59 V by using a low temperature I–V measurement. Finally, the working mechanism of the TiO₂NT array/MLG film Schottky junction PD is elucidated.     

Effect of Injection Parameters and Addition of Nanoscale Materials on the Shrinkage of Polypropylene Copolymer

The effect of variation of injection conditions and addition of nano-calcium carbonate (CaCO₃), nano-silicon dioxide (SiO₂) and full-vulcanized nano-powdered styrene butadiene rubber (PSBR) on the shrinkage of injection-molded polypropylene-ethylene copolymer (90/10, co-PP) were investigated. The results showed that the shrinkage was different for different locations along the flow path. The shrinkage in the length direction of the injection-molded sample varied with the adjustment of the processing parameters, while the shrinkage in the width and thickness direction was almost unchanged. The addition of nano-CaCO₃ and PSBR decreased the shrinkage of co-PP, while the shrinkage of co-PP/ SiO₂ composite was almost unchanged.     

Essential Work of Fracture Parameters of Injection-Molded Polypropylene/Polyolefin Elastomer Blends

The influence of polyolefin elastomer (POE) content on the fracture behavior of injection-molded polypropylene (PP)/POE blends was evaluated by means of the essential work of fracture (EWF) method. The results indicated that the EWF approach worked well for the PP/POE blends when POE content was 0～7.5 wt% of the blends. The specific essential work of fracture (w _e) increased with increasing POE content, and the dominant factor that affected w _e was the necking and subsequent fracture process. The specific nonessential work of fracture (βw _p) slightly decreased with increasing POE content, while the specific plastic work (w _p) showed an increasing trend with the decrease of the shape factor (β) of the specimen. Finally, it was shown that w _e could be predicted reasonably well via the COD values.     

Designing and Characterization of Biodegradable Multiblock Poly(L-Lactic Acid)/Polybutadiene Elastomers

A series of poly(L-lactic acid)/polybutadiene (PLA/PB) biodegradable multiblock elastomers was synthesized and characterized. A two-step process to prepare PLA/PB multiblock elastomers was applied. Melt polymerization was used to prepare poly(L-lactic acid) (PLA) terminated with hydroxyl groups and, at the same time, hydroxyl-terminated polybutadiene (HTPB) and 1,6-hexamethylene diisocyanate (HDI) were employed to synthesize diisocyanate-terminated polybutadiene (ITPB). Then, PLA and ITPB were reacted with different PLA/PB weight ratios. Consequently, a series of PLA/PB biodegradable poly(ester-urethane)s with crosslinked chains was obtained. Swelling characteristics and crosslink density of the crosslinked elastomer were investigated. DMA was applied to characterize its thermal properties. The measurement of mechanical properties showed that a PLA/PB elastomer with adjustable mechanical properties was synthesized. Micromorphology, hydrophobicity, and degradability of the material were also characterized.     

Injection Molding Shrinkage and Mechanical Properties of Polypropylene Blends

Polypropylene (PP) blends based on isotactic polypropylene (iPP), propylene-ethylene block copolymer (bPP), and propylene–ethylene random copolymer (rPP) were prepared by melt blending and the effects of content of bPP and rPP on the shrinkage during solidification and storage and mechanical properties of the blends were studied. It was found that the addition of polypropylene copolymer could effectively reduce the processing shrinkage of iPP and the lowest shrinkage of the blends was achieved at a loading of 2 wt% bPP or rPP. The flexural modulus and tensile strength of the blends decreased a little while the impact strength and elongation at break were improved greatly compared with those of iPP.     

Dynamical study on the stimulated processes of an exciton and a biexciton in a polymer

By applying a femtosecond stimulating pulse, we theoretically study the stimulated processes of an exciton and a biexciton in a polymer within the framework of an extended Su–Schrieffer–Heeger tight-binding model. For an exciton, it is obtained that the stimulated emission and absorption between the intragap levels take place with the same probability, by which we will not get the light amplification. However, the light amplification can be realized by the stimulated emission between the intragap levels in a biexciton, which is found to have two different modes. Finally, effect of the stimulating energy and intensity on the stimulated processes is separately analyzed. These results might be of great importance for further improving the optical applications of polymers, especially for optimizing the polymer laser properties.     

Rapid sonochemical synthesis of irregular nanolaminar-like Bi2WO6 as efficient visible-light-active photocatalysts

Irregular Bi₂WO₆ nanolaminars have been successfully synthesized via a rapid sonochemical approach using bismuth nitrate and tungstic acid as precursors in an aqueous solution. The characteristics of them were investigated in detail by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), N₂ adsorption, pore value, PL spectroscopy and UV–vis diffuse reflectance spectroscopy (UV–vis DRS). These irregular nanolaminars are of geometric shapes of orthorhombic Bi₂WO₆ with their basal plane being (0 0 1). They possess high crystallinity, lager surface area and pore value, which means fewer traps and stronger photocatalytic activity. The growth mechanism of such special nanolaminar was related to the sonochemical synthesis route, which played a key role in the formation of Bi₂WO₆ nanolaminar. Simultaneously, it was found that the formation of Bi₂WO₆ nanolaminar is a time dependent process. The Bi₂WO₆ nanolaminar has higher photocatalytic activity than bulk Bi₂WO₆ nanoparticle obtained by refluxing method for rhodamine B (Rh.B) degradation under visible light irradiation (λ > 400 nm).     

Effects of γ rays irradiation on structure and property of TiO2 thin films

TiO₂ thin films were deposited on a glass substrate by the radio frequency magnetron sputtering method, and annealed for 2 h at temperatures of 550°C. Then, ⁶⁰Co γ rays with different doses were used to irradiate the resulting TiO₂ thin films. The surface features of films before and after irradiation were observed by scanning electron microscope (SEM). Simultaneously, the crystal structure and optical properties of films before and after irradiation were studied by X-ray diffraction (XRD), UV–VIS transmission spectrum and Photoluminescence (PL) spectrum, respectively. The SEM analysis shows that the film is smooth with tiny particles on the film surface, and non-crystallization trend was clear after irradiated with γ rays. The XRD results indicated that the structure of the film at the room temperature mainly exists in the form of amorphous and mixed crystal at a sputtering power of 200 W, and non-crystallinity was more obvious after irradiation. Obvious difference can be found for the transmissibility of the irradiated and pre irradiation TiO₂ films by the UV-VIS spectra. The color becomes light yellow, and the new absorption edge also appeared at about 430 nm. PL spectra and photocatalysis experiments indicate that the photocatalysis degradation rate of the TiO₂ films on methylthionine chloride solution irradiated with the maximum dose can be increased to 90%.