Variation of the temperature factor of models on a ballistic range

A technique for variation of the temperature factor of free-flight models by varying their initial temperature is described. An experiment on a ballistic range is carried out with a free-flying supersonic blunt cone with a half-angle of 15° at a Mach number of 2.3. The flow at the cone base is studied in the transition range (from the laminar to turbulent flow) of Reynolds numbers. The base flow pattern is determined from the shadowgraphs of the flow about the models. The drag coefficient of the blunt cone at a zero angle of attack is found by processing trajectory data. It is found that the near wake geometries and the drag coefficients of the models tested at the laboratory temperature and a temperature of 120 K differ. Explanations of this effect are given.     

Adsorption of nonionic surfactant triton X-100 on solids from aqueous and nonaqueous solutions

The adsorption of nonionic surfactant Triton X-100 on quartz sand and methylated quartz sand from water and toluene was investigated by means of spectrophotometry, the radiotracer technique, and wetting angle measurements.     

Diffuse x-ray scattering study of the formation of microdefects in heat-treated dislocation-free large-diameter silicon wafers

Diffuse x-ray scattering (DXS) is used to study the formation of microdefects (MDs) in heat-treated dislocation-free large-diameter silicon wafers with vacancies. The DXS method is shown to be efficient for investigating MDs in silicon single crystals. Specific defects, such as impurity clouds, are found to form in the silicon wafers during low-temperature annealing at 450°C. These defects are oxygen-rich regions in the solid solution with diffuse coherent interfaces. In the following stages of decomposition of the supersaturated solid solution, oxide precipitates form inside these regions and the impurity clouds disappear. As a result of the decomposition of the supersaturated solid solution of oxygen, interstitial MDs form in the silicon wafers during multistep heat treatment. These MDs lie in the {110} planes and have nonspherical displacement fields. The volume density and size of MDs forming in the silicon wafers at various stages of the decomposition are determined.     

Calculation of the bond ionicity in complex oxides

A technique for calculating the bond ionicity of crystalline materials using electronegativities of elements and taking into account the structure of polyhedra of the complex-oxide structure is proposed.     

Scattering of a Rayleigh wave by monopole-dipole resonators

The problem of scattering of a Rayleigh wave by a chain of identical closely spaced monopole-dipole resonators with friction is considered. The values of resonator parameters that provide the rejection of the Rayleigh wave are found. The conditions under which the Rayleigh wave is much more efficiently reflected by the dipole resonators than by the monopole ones are determined.     

Graphitic nanofillers in PMMA nanocomposites—An investigation of particle size and dispersion and their influence on nanocomposite properties

Mechanical, thermal, and electrical properties of graphite/PMMA composites have been evaluated as functions of particle size and dispersion of the graphitic nanofiller components via the use of three different graphitic nanofillers: “as received graphite” (ARG), “expanded graphite,” (EG) and “graphite nanoplatelets” (GNPs) EG, a graphitic materials with much lower density than ARG, was prepared from ARG flakes via an acid intercalation and thermal expansion. Subsequent sonication of EG in a liquid yielded GNPs as thin stacks of graphitic platelets with thicknesses of ～10 nm. Solution‐based processing was used to prepare PMMA composites with these three fillers. Dynamic mechanical analysis, thermal analysis, and electrical impedance measurements were carried out on the resulting composites, demonstrating that reduced particle size, high surface area, and increased surface roughness can significantly alter the graphite/polymer interface and enhance the mechanical, thermal, and electrical properties of the polymer matrix. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2097–2112, 2007     

Gas solubility of carbon dioxide in poly(lactic acid) at high pressures: Thermal treatment effect

The sorption of carbon dioxide in glassy Poly(lactic acid) (PLA) films was studied by quartz crystal microbalance (QCM) at high pressures. Two thermal treatments, melted and quenched, were performed in PLA with two different L:D contents, 80:20 and 98:2, films and compared with a third thermal protocol, annealed, and used in a previous work. The results obtained show that for pressures higher than 2 MPa, the carbon dioxide solubility is larger in PLA 80:20 than in PLA 98:2, indicating that the L:D plays a dominant role on this property. The thermal treatments only affect the gas solubility in PLA 98:2. Sorption isotherms at temperatures 303, 313, and 323 K, below the glass transition temperature of the polymer, and pressures up to 5 MPa were measured and analyzed with three different models, the dual‐mode sorption model, the Flory–Huggins equation, and a modified dual‐mode sorption model where the Henry's law term was substituted by the Flory–Huggins equation. This last model performs especially well for CO₂ in PLA 80:20, due to the convex upward curvature of the solubility isotherms for that system. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 616–625, 2007     

Spectral properties of some problems in mechanics of strongly nonhomogeneous media

Spectral properties of the following three homogenized problems in the mechanics of strongly nonhomogeneous media are considered: the “double porosity” problem, the oscillation problem for a mixture of two viscous compressible liquids, and the oscillation of a medium consisting of an elastic frame and a viscous liquid. For all three cases results on the structure of the spectrum and on the existence of so-called “spectral gaps” are obtained.     

Hydrodynamics of an expanding fireball

A set of relativistic hydrodynamic equations is solved numerically on the basis of the flux-corrected SHASTA method for one-, two-, and three-dimensional geometries. The accuracy of the proposed method is demonstrated via a comparison with exact analytic solutions for the one-dimensional Riemann problem and a boost-invariant longitudinal expansion in the Bjorken model. The example of an expanding three-dimensional fireball for which initial conditions approximately correspond to PbPb collisions at an energy of about 160 GeV per nucleon is considered. This example indicates that the presumed dynamics of the expansion may affect substantially the results of an analysis of in-medium properties of hadrons that relies on data from experiments with leptons.