Towards the synthesis of MAX-phase functional coatings by pulsed laser deposition

Pulsed laser deposition with a Nd:YAG laser was used to grow thin films from a pre-synthesized Ti₃SiC₂ MAX-phase formulated ablation target on oxidized Si(1 0 0) and MgO(1 0 0) substrates. The depositions were carried out in a substrate temperature range from 300 to 900 K, and the pressure in the deposition chamber ranged from vacuum (10⁻⁵ Pa) to 0.05 Pa Argon background pressure. The properties of the films have been investigated by Rutherford backscattering spectrometry for film thickness and stoichiometric composition and X-ray diffraction for the crystallinity of the films. The silicon content of the films varied with the energy density of the laser beam. To suppress especially the silicon re-sputtering from the substrate, the energy of the incoming particles must be below a threshold of 20 eV. Therefore, the energy density of the laser beam must not be too high. At constant deposition energy density the film thickness depends strongly on the background pressure. The X-ray diffraction measurements show patterns that are typical of amorphous films, i.e. no Ti₃SiC₂ related reflections were found. Only a very weak TiC(2 0 0) reflection was seen, indicating the presence of a small amount of crystalline TiC.     

Interpretation of the polyelectrolyte and antipolyelectrolyte effects of poly(N‐vinylimidazole‐co‐sodium styrenesulfonate) hydrogels

Hydrogels of N‐vinylimidazole (VI) and sodium styrenesulfonate (SSS) were synthesized in aqueous solution by radical crosslinking copolymerization with N,N′‐methylene‐bis(acrylamide) as crosslinker. Swelling in several saline solutions was measured for hydrogel samples synthesized with different comonomer concentrations (C_T = 10, 25, or 40%) and with SSS mole fractions covering a broad range (f_SSS = 0–0.7), while the crosslinker ratio was 2 wt % in all cases. The degree of swelling in aqueous solution with a specific ionic strength (μ), plotted versus the SSS composition of the feed, shows a minimum for any set of samples synthesized with a fixed C_T. The dependence of swelling on μ shows both polyelectrolyte (f_SSS beyond the minimum) and antipolyelectrolyte behaviors (in the low f_SSS limit). It was found that the nonGaussian factor of the crosslinking density and the polymer‐solvent interaction parameter increase with f_SSS for any C_T. Moreover, in the low f_SSS limit, the osmotic swelling pressure is governed not only by the ionic contribution, but also by the polymer‐solvent mixing and, the concentration of mobile counterions inside the gel is not proportional to the net fixed charge but to the addition of cationic and anionic side groups, what discards the formation of ionic pairs. The antipolyelectrolyte effect is interpreted as due to the increasing protonation of VI as μ goes up. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1683–1693, 2007     

Synthesis of polysiltrimethylenes with trimethylsilyl groups in the branch of the main chain

The thermally initiated and platinum-catalyzed polymerization of 1-silacyclobutanes with substitutents containing a trimethylsilyl group was carried out. Soluble, high-molecular-weight, heterochain siltrimethylene polymers were obtained, containing trimethylsilyl groups removed from the main chain by various bridges.A. V. Topchiev Institute of Petrochemical Synthesis, Russian Academy of Sciences, 117912 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 1, pp. 223–225, January, 1992.     

Application of microwave digestion to the preparation of sediment samples for arsenic speciation

Several extraction procedures are described allowing arsenic speciation in sediments. The extraction of organometallic compounds such as dimethylarsinic acid or monomethylarsonic acid is quite simple since these compounds are stable in the different extraction media (HCl/ HNO₃, H₃PO₄, ammonium oxalate) and are easily released independent of the extraction mode (magnetic stirring or microwave solubilization). Extraction yields are higher than 96% for these two arsenic forms. An HCl/HNO₃ microwave solubilization procedure allows the quantitative solubilization of mineral arsenic, but the differentiation between the two oxidation states is not possible owing to the oxidation of As(III) to As(V). Extractions with orthophosphoric acid or ammonium oxalate allow the solubilization of mineral arsenic with extraction yields ranging from 90 to 95% and the differentiation between As(III) and As(V). Nevertheless, the amount of As(III) is underestimated owing to its partial oxidation. The usefulness and advantages of microwave solubilization compared with conventional extraction procedures are discussed. Received: 17 May 1996 / Revised: 19 September 1996 / Accepted: 25 September 1996     

On the ordering in [(C2H5)4N]2CuCl4 crystal: an X-ray study and theoretical considerations

The crystal structure [(C₂H₅)₄N]₂CuCl₄ has been determined by X-ray diffraction at 243K. The room temperature phase (phase I) belongs to the space group P4₂/nm [1] whereas the low temperature phase (phase II) is orthorhombic and belongs to the space group Pnna. The phase transition at T_c=258K is of improper ferroelastic type and it is associated with the ordering of the CuCl₄ ^2? and a partial ordering of the [(C₂H₅)₄N]⁺ ions which are disordered in the high temperature tetragonal phase. At lower temperature, there occurs another instability which could correspond to a complete ordering in the crystal.     

Corner spontaneous magnetization

Details are given of a new method allowing an exact calculation of the spontaneous magnetization in the corner as well as along the edge at an arbitrary distance of the corner for a rectangular planar Ising ferromagnet.     

Rotational temperature and density measurements in a hypersonic flow by dual-line CARS

Rotational temperature and nitrogen number density are measured in the shock wave/boundary layer interaction region in the vicinity of a two-dimensional compression corner disposed in a low pressure, 55 K, Mach 10 hypersonic air flow. Spatially-resolved data are recorded using a nonlinear optical technique named dual-line coherent anti-Stokes Raman scattering (DLCARS). Averaged temperature and density profiles are compared with those predicted by a Navier-Stokes solver. Good agreement is found.     

Cems characterization of SnO2 films obtained by sputtering and sol-gel route

Conversion electron Mössbauer spectroscopy (CEMS) has been used to study tin oxide films prepared by sol-gel dipping and sputtering. The spectra of films prepared by sol-gel route result close to that of crystalline SnO₂ after heat treatment at a temperature as low as 150°C. The Mössbauer parameters of as sputter deposited films indicate that the structure of the deposited stannic oxide has an amorphous character more pronounced for thinner samples. The structure becomes predominantly that of crystalline SnO₂ by heating at 550°C for 30 min provided the film thickness is higher than 10 nm.     

Riccati-based preconditioner for computing invariant subspaces of large matrices

Summary. This paper introduces and analyzes the convergence properties of a method that computes an approximation to the invariant subspace associated with a group of eigenvalues of a large not necessarily diagonalizable matrix. The method belongs to the family of projection type methods. At each step, it refines the approximate invariant subspace using a linearized Riccati's equation which turns out to be the block analogue of the correction used in the Jacobi-Davidson method. The analysis conducted in this paper shows that the method converges at a rate quasi-quadratic provided that the approximate invariant subspace is close to the exact one. The implementation of the method based on multigrid techniques is also discussed and numerical experiments are reported. Received June 15, 2000 / Revised version received January 22, 2001 / Published online October 17, 2001