Identification of peroxyacetic acid uroporphyrin I in the urine of patients with congenital erythropoietic porphyria by liquid chromatography and mass spectrometry

A new porphyrin, peroxyacetic acid uroporphyrin I, has been isolated from the urine of patients with congenital erythropoietic porphyria by reversed phase high performance liquid chromatography. The porphyrin was characterized by high resolution mass spectrometry and by typical chemical reactions of a peroxyacid.     

Arboricine and arboricinine, unusual tetracyclic indole regioisomers from Kopsia

A pair of unusual regioisomeric tetracyclic indoles of the corynantheine-type, arboricine and arboricinine were obtained from the Malayan Kopsia arborea. The structures were established by spectroscopic analysis and a possible biogenetic link between the alkaloids is presented.     

Evaluation of compatibility in polymer blend systems by simultaneous DSC-FTIR measurement

The concept of crystallization dynamics method evaluating the miscibility of binary blend system including crystalline component was proposed. Three characteristic rates, nucleation, crystal growth rates (N*, G*) and growth rate of conformation (G _c*) were used to evaluate the miscibility of PVDF/at-PMMA and PVDF/iso-PMMA by the simultaneous DSC-FTIR. N*, G* and G _c* depended remarkably on both temperature and blend fraction (ϕ_PMMA) for PVDF/at-PMMA system, which indicated the miscible system. PVDF/iso-PMMA showed small ϕ_PMMA dependency of N*, G* and G _c*, was estimated the immiscible system. The ΔT/T _m⁰ values, corresponding to Gibbs energy required to attend the constant G* and G _c*, evaluated from G* and G _c* showed the good linear relationships with different slope. The experimental results suggested that the concentration fluctuation existed in PVDF/iso-PMMA system.     

The impact of nonequilibrium gain in a spectral laser diode model

We describe the inclusion of nonequilibrium gain into a self-consistent 2.5D CW spectral laser diode model and report on the use of this model to investigate the origin of gain compression in a 975 nm high-brightness tapered QW laser diode. Nonequilibrium gain is calculated using a dynamic gain model, which simulates the dynamic relaxation of the quantum well carrier energy distributions under the influence of steady-state electrical and optical excitation. Calculated gain and spontaneous emission spectra are included in the laser model via parameterised look up tables. Both simulated and experimentally measured intracavity spontaneous emission spectra show an increased carrier density and a blue-shift of the gain maximum with increasing bias caused by carrier heating and spectral hole burning. The accurate incorporation of nonequilibrium gain compression is therefore vital for the accurate prediction of the operating characteristics of these devices and for the experimental determination of the active region temperature.     

Characteristics of Ti0.97Co0.03O2:Sb0.01 dilute magnetic semiconducting thin films deposited at 500 °C by pulsed laser deposition

Epitaxial Ti_0.97Co_0.03O₂:Sb_0.01(TCO:Sb) films were deposited on R-Al₂O₃ (1 1 0 2) substrates at 500 °C in various deposition pressures by pulsed laser deposition. The solubility of cobalt within the films increases with decreasing deposition pressure at a deposition temperature of 500 °C. The TCO:Sb films deposited at 5×10⁻⁶ Torr exhibit a p-type anomalous Hall effect having a hole concentration of 6.1×10²²/cm³ at 300 K. On the other hand, films deposited at 4×10⁻⁴ Torr exhibits an n-type anomalous Hall effect having an electron concentration of about 1.1×10²¹/cm³. p- or n-type DMS characteristics depends on the change of the structure of TCO:Sb films and the solubility of Co is possible by controlling the deposition pressure.     

Badge-type diffusive sampler using 3-methyl-2-benzothiazolinone hydrazone for measuring formaldehyde in indoor air.

The evaluation of a badge-type diffusive sampler for measuring formaldehyde using 3-methyl-2-benzothiazolinone hydrazone (MBTH) was investigated. On average, the formaldehyde concentration in blanks was reduced by approximately 31% by cleaning procedures. The cleaning techniques did not significantly differ in effectiveness. The maximum sampling rate was 22.4 +/- 3.5 mL min(-1) at MBTH concentrations of 0.05%. The formaldehyde concentration in blanks did not appreciably increase over a period of about 1 month at room temperature, and was 0.36 +/- 0.03 microg, with a relative standard deviation of 8%. The diffusive sampler had good precision and accuracy for measuring formaldehyde in indoor environments. For a 24-h exposure time, the limits of detection and quantification calculated with the field blanks were 9.7 and 13.8 ppb, respectively. The minimum exposure times were calculated based on the measured and calculated limits of quantification, the sampling rate, and the atmospheric formaldehyde concentration. The capacity of the diffusive sampler with 0.5% MBTH was 3 ppm h(-1), approximately 1.5-times the capacity when the MBTH concentrations were 0.05%.     

Direct single-layered fabrication of 3D concavo–convex patterns in nano-stereolithography

A nano-surfacing process (NSP) is proposed to directly fabricate three-dimensional (3D) concavo–convex-shaped microstructures such as micro-lens arrays using two-photon polymerization (TPP), a promising technique for fabricating arbitrary 3D highly functional micro-devices. In TPP, commonly utilized methods for fabricating complex 3D microstructures to date are based on a layer-by-layer accumulating technique employing two-dimensional sliced data derived from 3D computer-aided design data. As such, this approach requires much time and effort for precise fabrication. In this work, a novel single-layer exposure method is proposed in order to improve the fabricating efficiency for 3D concavo–convex-shaped microstructures. In the NSP, 3D microstructures are divided into 13 sub-regions horizontally with consideration of the heights. Those sub-regions are then expressed as 13 characteristic colors, after which a multi-voxel matrix (MVM) is composed with the characteristic colors. Voxels with various heights and diameters are generated to construct 3D structures using a MVM scanning method. Some 3D concavo–convex-shaped microstructures were fabricated to estimate the usefulness of the NSP, and the results show that it readily enables the fabrication of single-layered 3D microstructures. PACS 85.40.Hp; 81.16.Nd; 42.82.Cr