GS-221高速摄影测量仪测角信息的采集与处理

在GS-221高速摄影测量仪中,测角信息采集与处理速度的快慢是重要性能指标之一。本文讨论了如何在尽可能短的时间内对测角信息进行采集和处理的软件实现方法。     

吹气孔直径对RH精炼过程钢液流动和混合特性的影响

针对90t RH精炼装置,以水力学模拟研究了吹气孔直径对真空循环精炼过程中钢液流动和混合特性的影响.模型和原型的相似比为15.模型吹气孔直径分别为0.8 mm和1.2 mm.结果表明,1.2 mm孔径下环流量和主要工艺参数间的关系为Ql Q80.26Du0.69Dd0.80;在给定的吹气量和插入管内径下,增大吹气孔直径并不显著改变精炼过程中钢液流动特征,环流量随吹气孔直径的增大而略有增大,其关系式为Ql=2.40Q 0.23gD0.72u D0.88d d0.13in;相应地,混合时间稍有缩短;0.8和1.2 mm孔径下,τm与搅拌能密度的关系分别为τm ε5和τm ε0.49.     

Vacuum Fluctuations and Motion of a Charged Test Particle in a Cylindrical Spacetime

The effects of quantum electromagnetic fluctuations upon the motion of a test charged particle are examined in a cylindrical spacetime in which one spatial is compactified. The mean squared fluctuations in the velocity and position of the test particle are calculated. It is found that the random motion of the test particle will be anisotropic. The possible consequences for theories with extra compactified spatial dimensions are discussed.     

一种新型有机电致微腔结构的双模发射

采用结构Glass／DBR／ITO／NPB／NPB：Alq／Alq／Al制作了有机微腔电致发光器件。将空穴传输材料与发光材料以一定比例混合作为发光层，为了便于对比，在不改变有机层的膜厚的情况下同时制作了传统的异质结微腔器件，发现两种器件的发光光谱有很大不同，器件的复合效率与传统的异质结器件相比也得到了很大提高，这是因为将两种有机材料混合能消除界面势垒，提高器件的复合效率，从而提高了器件的发光性能，实现了微腔双模发射，且两个模式的半峰全宽分别为8nm和12nm。通过进一步优化器件结构可以实现微腔白光发射。     

70个南天旋涡星系等值厚度的测定

利用彭秋和提出的方法以及分析星系的旋涡图样 ,得到 70个南天旋涡星系的等值厚度 ,这些星系的图象是从北京天文台兴隆观测站Palomar天图数字光盘 (theDigitizedSkySurvey)中读出的 .为了得到星系的最佳倾角 (星系平面与天球切平面之间的夹角 ) ,把用最小二乘法拟合得到的对数螺线画在星系图象上与旋臂进行比对 ,反复调节星系的倾角 ,使拟合得到的对数螺线能很好地与旋臂吻合 ,从而得出星系的最佳倾角.     

k-order Slant Toeplitz Operators on the Bergman Space

In this paper κ-order slant Toeplitz operator on the Bergman space is defined. Some properties like spectrum, commuting are discussed.     

Reduction of Dislocations in GaN Epilayer Grown on Si （111） Substrates using a GaN Intermedial Layer

GaN intermedial layers grown under different pressures are inserted between GaN epilayers and AIN/Si（111） substrates. In situ optical reflectivity measurements show that a transition from the three-dimensional （3D） mode to the 2I） one occurs during the GaN epilayer growth when a higher growth pressure is used during the preceding GaN intermedial layer growth, and an improvement of the crystalline quality of GaN epilayer will be made. Combining the in situ reflectivity and transmission electron microscopy （TEM） measurements, it is suggested that the lateral growth at the transition of growth mode is favourable for bending of dislocation lines, thus reducing the density of threading dislocations in the epilayer.     

Phenylene vinylene‐based electroluminescent polymers with electron transport block in the main chain

We report a new route for the design of soluble phenylene vinylene (PV) based electroluminescent polymers bearing electron‐deficient oxadizole (OXD) and triazole (TZ) moieties in the main chains with the aryloxy linkage. Both series of the PV‐based polymers were prepared by Wittig reaction. By properly adjusting the OXD and/or TZ content through copolymerization, we can achieve an enhanced balance of hole‐ and electron injections, such that the device efficiency is significantly improved. Light‐emitting diodes fabricated from P1, P2, P3, P4, P5, P6, and P7 with the configuration of Indium–Tin Oxide (ITO)/Poly (styrene sulfonic acid) doped poly (ethylenedioxythiophene) (PEDOT)/polymer/Ca/Al, emit bright green light with the maximum peak around 500 nm. For the device using the optimal polymer (P4) as emitting layer, a maximum brightness of 1300 cd/m² at 20 V and a maximum luminance efficiency of 0.325 cd/A can be obtained. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3469–3478, 2006