Extractive spectrophotometric determination of Cobalt(II) in synthetic and pharmaceutical samples using Cyanex 923.

Cyanex 923 has been proposed as a sensitive analytical reagent for the direct extractive spectrophotometric determination of cobalt(II). Cobalt(II) forms a blue-colored complex with Cyanex 923 in the organic phase. The maximum absorbance of the complex is measured at 635 nm. Beer's law was obeyed in the range 58.9 - 589.0 microg of cobalt. The molar absorptivitiy and Sandell's sensitivity of the complex was calculated to be 6.79 x 10920 l mol(-1) cm(-1) and 0.088 microg cm(-2), respectively. The nature of the extracted species was found to be Co(SCN)2 x 2S. An excellent linearity with a correlation coefficient value of 0.999 was obtained for the Co(II)-Cyanex 923 complex. Stability and regeneration of the reagent (Cyanex 923) for reuse is the main advantage of the present method. The method was successfully applied to the determination of cobalt in synthetic mixtures and pharmaceutical samples was found to give values close to the actual ones. Standard alloy samples, such as high-speed tool BCS 484 and 485, have been tested for the determination of cobalt for the purpose of validating the present method. The results of the proposed method are comparable with atomic absorption spectrometry and were found to be in good agreement.     

Preparation and characterization of finely dispersed drugs. 5. Ethyl 3,5-di(acetylamino)-2,4,6-triiodobenzoate

Controlled precipitation of the diagnostic imaging agent ethyl 3,5-di(acetylamino)-2,4,6-triiodobenzoate has been used to produce fine particles of various sizes, morphologies, and degrees of crystallinity, which depended on experimental conditions. In addition, two distinct polymorphic forms of the drug have been fully characterized by single crystal X-ray diffraction studies, and evidence for a third polymorph was also observed. Some of the so prepared dry particles were coated with a thin layer of silica.     

Fold‐2‐covering triangular embeddings

For a graph G and a positive integer m, G_(m) is the graph obtained from G by replacing every vertex by an independent set of size m and every edge by m² edges joining all possible new pairs of ends. If G triangulates a surface, then it is easy to see from Euler's formula that G_(m) can, in principle, triangulate a surface. For m prime and at least 7, it has previously been shown that in fact G_(m) does triangulate a surface, and in fact does so as a “covering with folds” of the original triangulation. For m = 5, this would be a consequence of Tutte's 5‐Flow Conjecture. In this work, we investigate the case m = 2 and describe simple classes of triangulations G for which G₍₂₎ does have a triangulation that covers G “with folds,” as well as providing a simple infinite class of triangulations G of the sphere for which G₍₂₎ does not triangulate any surface. © 2003 Wiley Periodicals, Inc. J Graph Theory 43: 79–92, 2003     

Karhunen–Loeve representations of turbulent channel flows using the method of snapshots

For three‐dimensional flows with one inhomogeneous spatial coordinate and two periodic directions, the Karhunen–Loeve procedure is typically formulated as a spatial eigenvalue problem. This is normally referred to as the direct method (DM). Here we derive an equivalent formulation in which the eigenvalue problem is formulated in the temporal coordinate. It is shown that this so‐called method of snapshots (MOS) has some numerical advantages when compared to the DM. In particular, the MOS can be formulated purely as a matrix composed of scalars, thus avoiding the need to construct a matrix of matrices as in the DM. In addition, the MOS avoids the need for so‐called weight functions, which emerge in the DM as a result of the non‐uniform grid typically employed in the inhomogeneous direction. The avoidance of such weight functions, which may exhibit singular behaviour, guarantees satisfaction of the boundary conditions. The MOS is applied to data sets recently obtained from the direct simulation of turbulence in a channel in which viscoelasticity is imparted to the fluid using a Giesekus model. The analysis reveals a steep drop in the dimensionality of the turbulence as viscoelasticity is increased. This is consistent with the results that have been obtained with other viscoelastic models, thus revealing an essential generic feature of polymer‐induced drag reduced turbulent flows. Published in 2006 by John Wiley & Sons, Ltd.     

Time-resolved synchrotron X-ray study of crystalline phase transition in poly(aryl ether ketone ketone) containing alternated terephthalic/isophthalic moieties

Unique crystallization and melting behavior in poly(aryl ether ketone ketone) containing alternated terephthalic and isophthalic moieties were studied by time-resolved synchrotron x-ray methods. Recently, this material has been shown to exhibit three polymorphs (forms I, II, and III). In this work, we further investigated their distinctive thermal properties and found that form I is the dominating and the most thermally stable phase while form II is favored by fast nucleation conditions and is the least stable phase. On the other hand, form III represents a minor intermediate phase that usually coexists with form I and can be transferred from form II and to form I. Structural and morphological changes in form I have been followed by simultaneous wide-angle x-ray diffraction (WAXD)/small-angle x-ray scattering (SAXS) measurements during cold- or melt-crystallization and subsequent melting. In all cases, a larger dimensional change was found in the crystallographic a-axis than the b-axis during heating and cooling. This may be due to the greater lateral stress variation with respect to temperature along the a direction of the primary lamellae which is induced by either the formation of secondary lamellae or the preferential chain-folding direction in poly(aryl ether ketone ketone)s. During the phase transitions of form II ← III in the cold-crystallized specimen and form III ← I in the melt-crystallized samples, lamellar variables (long period, lamellar thickness, and invariant) obtained from SAXS remain almost constant. This indicates that the density distribution in the long spacing is independent of the melting in form II or III. For melt-crystallization, the corresponding changes in unit-cell dimensions and lamellar morphology during the annealing-induced low endotherm are most consistent with the argument that these changes are due to the melting of thin lamellar population. © 1995 John Wiley & Sons, Inc.     

Development of new dyes for use in integrated optical sensors

New chromoionophores have been developed, focused on NIR applications so that optode membranes may be used in monolithically integrated optical sensors. The wavelength of maximum absorbance has been estimated for a new model compound by the Pariser-Parr-Pople (PPP) method. Several cyanine type dyes have been tested as membrane chromoionophores. Membrane composition has been altered to overcome solubility problems. In this way, simple pH-sensitive optode membranes have been produced.     

Database reverse engineering: From requirements to CARE tools

This paper analyzes the requirements that CASE tools should meet for effective database reverse engineering (DBRE), and proposes a general architecture for data-centered applications reverse engineering CASE environments. First, the paper describes a generic DBMS-independent DBRE methodology, then it analyzes the main characteristics of DBRE activities in order to collect a set of desirable requirements. Finally, it describes DB-MAIN, an operational CASE tool developed according to these requirements. The main features of this tool that are described in this paper are its unique generic specification model, its repository, its transformation toolkit, its user interface, the text processors, the assistants, the methodological control and its functional extensibility. Finally, the paper describes five real-world projects in which the methodology and the CASE tool were applied. This is a heavily revised and extended version of “Requirements for Information System Reverse Engineering Support” by J.-L. Hainaut, V. Englebert, J. Henrard, J.-M. Hick, D. Roland, which first appeared in the Proceedings of the Second Working Conference on Reverse Engineering, IEEE Computer Society Press, pp. 136–145, July 1995. This paper presents some results of the DB-MAIN project. This project is partially supported by the Région Wallonne, the European Union, and by a consortium comprising ACEC-OSI (Be), ARIANE-II (Be), Banque UCL (Lux), BBL (Be), Centre de recherche public H. Tudor (Lux), CGER (Be), Cockerill-Sambre (Be), CONCIS (Fr), D'Ieteren (Be), DIGITAL, EDF (Fr), EPFL (CH), Groupe S (Be), IBM, OBLOG Software (Port), ORIGIN (Be), Ville de Namur (Be), Winterthur (Be), 3 Suisses (Be). The DB-Process subproject is supported by the Communauté Fran?aise de Belgique.     

Orbifolds, Sheaves and Groupoids

We characterize orbifolds in terms of their sheaves, and show that orbifolds correspond exactly to a specific class of smooth groupoids. As an application, we construct fibered products of orbifolds and prove a change-of-base formula for sheaf cohomology.     

Selective saturation and inversion of multiple resonances in high-resolution solid-state 13C experiments using slow spinning CP/MAS and tailored DANTE pulse sequences.

Taking advantage of the long 13C T1 values generally encountered in solids, selective saturation and inversion of more than one resonance in 13C CP/MAS experiments can be achieved by sequentially applying several DANTE pulse sequences centered at different transmitter frequency offsets. A new selective saturation pulse sequence is introduced composed of a series of 90 degrees DANTE sequences separated by interrupted decoupling periods during which the selected resonance is destroyed. Applications of this method, including the simplification of the measurement of the principal values of the 13C chemical shift tensor under slow MAS conditions, are described. The determination of the aromaticity of coal using a relatively slow MAS rate is also described.     

Magnetic resonance imaging: a new window into industrial processing.

Although the most important use of nuclear magnetic resonance imaging (MRI) continues to be for diagnostic medicine, recognition is being gained for many nonmedical applications. Examples include the following areas: petrogeology, food, agriculture, polymers and polymer-composites, and pharmaceuticals. These areas all involve studies of species that have short spin-spin relaxation times, and consequently need far fast gradient switching. These technical details are discussed and typical applications given.