A laser Doppler anemometry technique for Reynolds stresses measurement

A technique is described for the measurement of all components of mean velocity and Reynolds stresses, in a complex turbulent flow where achieving coincidence data acquisition is difficult. The method is based on data recorded using four orientations of the laser probe. It is shown that the measurement errors are not the same for all the components of the Reynolds tensor, but they are sufficiently small to give a good accuracy. An application to a turbomachinery flow is given to illustrate the method.     

Nano-tribological study on a super-hydrophobic film formed on rough aluminium substrates

A novel super-hydrophobic stearic acid (STA) film with a water contact angle of 166^o was prepared by chemical adsorption on aluminum wafer coated with polyethyleneimine (PEI) film. The micro-tribological behavior of the super-hydrophobic STA monolayer was compared with that of the polished and PEI-coated Al surfaces. The effect of relative humidity on the adhesion and friction was investigated as well. It was found that the STA monolayer showed decreased friction, while the adhesive force was greatly decreased by increasing the surface roughness of the Al wafer to reduce the contact area between the atomic force microscope (AFM) tip and the sample surface to be tested. Thus the friction and adhesion of the Al wafer was effectively decreased by generating the STA monolayer, which indicated that it could be feasible and rational to prepare a surface with good adhesion resistance and lubricity by properly controlling the surface morphology and the chemical composition. Both the adhesion and friction decreased as the relative humidity was lowered from 65% to 10%, though the decrease extent became insignificant for the STA monolayer. The project supported by the National Natural Science Foundation of China (50375151, 50323007, 10225209) and the Chinese Academy of Sciences (KJCX-SW-L2)     

Photorefractive Four-Wave Mixing Switches Utilizing Pockels Effect -Longitudinal and Lateral Switches-

We carried out detailed calculations for photorefractive wave-mixing switches based on one of three crystals with high electro-optic coefficients, namely, BaTiO₃, Strontium Barium Niobate (SBN (0.75)), and Potasium Sodium Strontium Barium Niobate (KNSBN). A comparison of results for the three crystals shows that a 0_-cut BaTiO³ crystal is suitable for a longitudinal switch and requires a voltage of about 80 for a 2-mm-thick crystal to induce sufficient phase mismatch. The electrodes must be transparent for the incident and diffracted beams. A 45_-cut SBN (0.75) crystal, however, is suitable for a lateral switch and requires a voltage of about 150 for a 1-mm-wide crystal. The electrodes do not need to be transparent.     

Color Zone Map in Peripheral Vision at Various Illuminance Levels

We measured the entire region of mesopic and photopic vision to determine the color zone covering the visual field with unique red, yellow, green, and blue hue components. Eight kinds of test stimuli in the natural color system (NCS) color notation system were used. These stimuli were presented at horizontal and vertical meridians, and at meridians inclined at 45° angles. The illuminance level was set at six levels: 0.01 lx-1000 lx. The evaluation method measured chromatic, white, and black components as well as the hue component of the stimuli. Results show that the color zone of the retina extended further into the periphery with increasing illuminance; the response of opponent colors y-b was shown to be greater than that of the opponent colors r-g.     

Real-time color holographic interferometry devoted to 2D unsteady wake flows

A new optical technique based on real time holographic interferometry in true colors has been implemented around the transonic wind tunnel of the ONERA-Lille center to analyze 2D unsteady wake flows. Tests realized in color interferometry, real time and double exposure, use simultaneously three wavelengths of a continuous waves laser (argon and krypton mixed) and holograms are recorded on silver-halide single-layer panchromatic Slavich PFG03c plates. The very principle of real-time true color holographic interferometry uses three primary wavelengths (red, green and blue) to record, under no-flow conditions, the interference among the three measurement beams and the three reference beams simultaneously on a single reference hologram. After the holographic plate is developed, it is placed on the test setup again in the position it occupied during exposure and the hologram is illuminated again by the three reference beams and three measurement beams. A flat, uniform color can then be observed behind the hologram. So a horizontal, vertical, or even circular fringe pattern can be formed and the achromatic central fringe can be made out very clearly. The single color is used to determine the path difference zero on the interferograms. The flow studied was the unsteady flow downstream of a cylinder placed crosswise in the test section. A sequence of hundred interferograms was recorded on the flow around the cylinder at Mach 0.37. The vortex formation and dissipation phases can be seen very clearly, along with the fringe beat to either side of the cylinder.     

The glow curve structure for the LiF:Mg,Cu,Na,Si TL detector with dopants concentrations and sintering temperatures

The glow curve structures for LiF:Mg,Cu,Na,Si TL detectors with various dopant concentrations and sintering temperatures were investigated for the improvement of the glow curve structure and sensitivity of the TL detector. The dopant concentrations were varied over the following ranges: Mg (0–0.25 mol%), Cu (0–0.07 mol%), Na and Si (0–1.5 mol%). With increasing Cu concentration, the intensity of the main peak was intensified and reached a maximum at a concentration of 0.05 mol%. The high-temperature peak was reduced. The dependency of the main peak intensity on the Mg concentration exhibits a sharp maximum at 0.2 mol%. The intensity of the high-temperature peak tends to rise slightly with increasing Mg concentration. It was found that the optimum concentrations of the dopants in the LiF:Mg,Cu,Na,Si TL material are Mg: 0.2 mol%, Cu: 0.05 mol%, Na and Si: 0.9 mol%. The dependency of the main peak intensity on sintering temperature exhibits a very sharp maximum at 830°C. The high-temperature peak was rapidly reduced after 825°C.     

Intramolecular energy transferable (2,2‐diphenylvinyl)phenyl substituted poly(p‐phenylenevinylene) derivative with efficient photoluminescence and electroluminescence

A poly(p‐phenylenevinylene) (PPV) derivative containing a bulky (2,2‐diphenylvinyl)phenyl group in the side chain, EHDVP‐PPV, was synthesized by Gilch route. The reduced tolane‐bisbenzyl (TBB) defects, as well as the structure of the polymer, was confirmed by various spectroscopic methods. The intramolecular energy transfer from the (2,2‐diphenylvinyl)phenyl side group to the PPV backbone was studied by UV‐vis and photoluminescence (PL) of the obtained polymer and model compound. The polymer film showed maximum absorption and emission peaks at 454 and 546 nm, respectively, and high PL efficiency of 57%. A yellow electroluminescence (λ_max = 548 nm) was obtained with intensities of 6479 cd/m² when the light‐emitting diodes of ITO/PEDOT/EHDVP‐PPV/LiF/Al were fabricated. The maximum power efficiency of the devices was 0.729 lm/W with a turn‐on voltage of 3.6 V. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5636–5646, 2004     

Effect of photoinitiator on photopolymerization of inorganic–organic hybrid polymers (ORMOCER®)

Inorganic–organic hybrid polymers have been developed and tested for evaluation in optical and electrical applications. Although hybrid inorganic–organic polymers can be synthesized by sol–gel chemistry at first, the physical properties of hybrid inorganic–organic polymers are changed during thin film-making processes, that is, photocuring and thermal curing. To investigate the effect of photoinitiator on the material properties during processing, a model system containing methacrylic groups as organically polymerizable units was selected. The conversion of CC double bond of methacrylic groups depending on some kinds of photoinitiator quantities was characterized by Fourier transform infrared spectroscopy. It was confirmed to correlate the degree of CC double bond conversion with the refractive indices. Thermodynamically, the enthalpy of the photopolymerization of hybrid polymer was investigated by UV–DSC. UV–DSC spectra showed the exothermic nature of photopolymerization of ORMOCER® to be in dependence of photoinitiator quantities. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1979–1986, 2004     

Synthesis and characterization of soluble polyimides containing trifluoromethyl groups in their backbone

A series of polyimides were synthesized from 2,2‐Bis(3,4‐dicarboxyphenyl)hexafluoropropane, 2,2‐bis(3‐amino‐4‐hydroxyphenyl)‐hexafluoropropane, and 4,4′‐oxydianiline by chemical imidization. The effects of the diamine ratios on the properties of the films were evaluated through the study of their thermal, electrical, and morphological properties. All the polymers exhibited better solubility in most of the organic solvents and hence were easily processable. Polyimides with more 2,2‐bis(3‐amino‐4‐hydroxyphenyl)‐hexafluoropropane exhibited better solubility and a low refractive index, which is highly desired for microelectronic applications. The dielectric constant and birefringence were strongly dependent on the fluorine content. With an increase in the fluorine substitution, both the dielectric constant and birefringence decreased. All the polymers exhibited high thermal stability (>400 °C). The absence of crystalline melting in differential scanning calorimetry and broad wide‐angle X‐ray diffraction patterns revealed the amorphous nature of the polymers, which was due to the presence of bulky CF₃ groups and hinged ether linkages of the diamine component. The residual stress values decreased with an increase in the 4,4′‐oxydianiline content, and the results were in agreement with the dielectric constant. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4303–4312, 2004