Reliable evaluation of temperature-independent parameters in correlation of vapour–liquid equilibrium data

A new algorithm/program has been elaborated for simultaneous processing of different sets of vapour–liquid equilibrium data. The program was tested with six binary hexane + isomeric pentanol systems, each of them measured at three different isobaric conditions and one isothermal system of tert-butyl-methyl-ether + 2-methyl-2-propanol measured at three different temperatures. The correlation uses the maximum likelihood method, taking into account real behaviour of vapour phase. The parameters obtained are valid within the whole temperature range of the data, and are consistent in comparison with those obtained from individual correlations of isobars or isotherms. Results are presented for the Wilson and NRTL equations.     

Bonding Properties of a Novel Inorganometallic Complex, Ru(SnPh(3))(2)(CO)(2)(iPr-DAB) (iPr-DAB = N,N'-Diisopropyl-1,4-diaza-1,3-butadiene), and its Stable Radical-Anion, Studied by UV-Vis, IR, and EPR Spectroscopy, (Spectro-) Electrochemistry, and Density Functional Calculations

Ru(SnPh(3))(2)(CO)(2)(iPr-DAB) was synthesized and characterized by UV-vis, IR, (1)H NMR, (13)C NMR, (119)Sn NMR, and mass (FAB(+)) spectroscopies and by single-crystal X-ray diffraction, which proved the presence of a nearly linear Sn-Ru-Sn unit. Crystals of Ru(SnPh(3))(2)(CO)(2)(iPr-DAB).3.5C(6)H(6) form in the triclinic space group P&onemacr; in a unit cell of dimensions a = 11.662(6) ?, b = 13.902(3) ?, c = 19.643(2) ?, alpha = 71.24(2) degrees, beta = 86.91(4) degrees, gamma = 77.89(3) degrees, and V = 2946(3) ?(3). One-electron reduction of Ru(SnPh(3))(2)(CO)(2)(iPr-DAB) produces the stable radical-anion [Ru(SnPh(3))(2)(CO)(2)(iPr-DAB)](*-) that was characterized by IR, and UV-vis spectroelectrochemistry. Its EPR spectrum shows a signal at g = 1.9960 with well resolved Sn, Ru, and iPr-DAB (H, N) hyperfine couplings. DFT-MO calculations on the model compound Ru(SnH(3))(2)(CO)(2)(H-DAB) reveal that the HOMO is mainly of sigma(Sn-Ru-Sn) character mixed strongly with the lowest pi orbital of the H-DAB ligand. The LUMO (SOMO in the reduced complex) should be viewed as predominantly pi(H-DAB) with an admixture of the sigma(Sn-Ru-Sn) orbital. Accordingly, the lowest-energy absorption band of the neutral species will mainly belong to the sigma(Sn-Ru-Sn)-->pi(iPr-DAB) charge transfer transition. The intrinsic strength of the Ru-Sn bond and the delocalized character of the three-center four-electron Sn-Ru-Sn sigma-bond account for the inherent stability of the radical anion.     

Polyethene with pendant fullerene moieties

Polyethene with fullerene moieties pendant on short-chain branches was prepared by the catalytic copolymerization of ethene and a fullerene-containing vinylic comonomer, yielding polyethene copolymers containing up to 25 wt% of C60.     

Properties of ITO films prepared by reactive magnetron sputtering

Indium tin oxide (ITO) thin films were deposited by mid frequency pulsed dual magnetron sputtering using a metallic alloy target with 10 wt.% tin in an atmosphere of argon and oxygen. The aim of the work was to study the interdependence of structural, electrical and optical properties of ITO films deposited in the reactive and transition target mode, respectively. The deposition rate in the transition mode exceeds the deposition rate in the reactive mode by a factor of six, a maximum value of 100 nm·m min⁻¹ could be achieved. This corresponds to a static deposition rate of 200 nm min⁻¹. The lowest electrical resistivity of 1.1·10⁻³ Ω cm was measured at samples deposited in the high oxygen flow range in the transition mode. The samples show a good transparency in the visible range corresponding to extinction coefficients being below 10⁻². X-ray diffraction was used to characterise crystalline structure as well as film stress. ITO films prepared in the transition mode show a slightly preferred orientation in (211) direction, whereas films deposited in the reactive mode are strongly (222) oriented. Compared to undoped In₂O₃ all samples have an enlarged lattice. The lattice strain perpendicular to the surface is about 0.8% and 2.0% for films grown in the transition and the reactive mode, respectively. Deposition in the transition mode introduces a biaxial film stress in the range of −300 MPa, while stress in reactive mode samples is −1500 MPa.     

Intercalation of Dyes Containing SO3H Groups into Zn–Al Layered Double Hydroxide

The intercalates of Naphthol Yellow S, Tropaeolin 000, and Tropaeolin 00 were prepared by heating [Zn_0.67Al_0.33(OH)₂](CO₃)_0.165 · 0.5H₂O with acidic forms of the dye solutions in an open reaction vessel. The intercalates were characterized by chemical and thermal analysis, X-ray powder diffraction and UV–VIS spectroscopy. A possible arrangement of the dye molecules in the intercalates was suggested on the basis of their chemical compositions and interlayer distances, by taking into account van der Waals dimensions of the guest molecules and by assuming that the structure of the host layers is not changed during the intercalation process.     

Dynamic imaging of single DNA-protein interactions using atomic force microscopy

Atomic force microscopy (AFM) imaging of static DNA-protein complexes, in air and in liquid, can be used to directly obtain quantitative and qualitative information on the structure of different complexes. For example, DNA length, the location of preferential binding sites for proteins and bending of DNA as a result of the complexation can all be measured. Recording consecutive AFM images of DNA and protein molecules under conditions that they are still able to move and interact, or dynamic AFM imaging, however, can reveal information on the dynamic aspects of the interactions between these molecules. Here, an overview is given of the technical challenges that need to be considered for successful dynamic AFM imaging studies of individual DNA-protein interactions. Necessary technical improvements to the AFM set-up and the development of new sample preparation methods are described in this paper.     

N-heterocyclic carbenes as ligands in high-valent molybdenum and tungsten complexes

Oxometal complexes of molybdenum and tungsten in high oxidation states from stable adducts with 1,3-dimethylimidazoline-2-ylidene (L) 1. The first ‘carbene’ complexes of molybdenum(VI) [MoO₂Cl(L)₃]Cl (3a) and tungsten(VI) WO₂Cl₂(L)₂ (4b) are reported.