Physical aging of a polyetherimide: Creep and DSC measurements

Creep and differential scanning calorimetry (DSC) measurements have been used to study the physical aging behavior of a polyetherimide. Isothermal aging temperatures ranged from 160°C to T_g with aging times ranging from 10 min to 8 days. The only measurable effect of physical aging on the short-time creep curves is a shift of the creep compliance to longer times. Andrade plots of the compliance versus the cube root of time are linear at short times with the slope β decreasing with increasing aging time to a constant value once equilibrium is reached. Log β³ is related directly to the degree to which the creep curves shift to longer times with physical aging, and is used in this work as a measure of physical aging. A reduced curve of log β³ versus log aging time is obtained for the aging temperatures investigated by appropriate vertical and horizontal shifts. The enthalpy change during aging increases linearly with the logarithm of the aging time, t_a, leveling off at equilibrium at values which increase with decreasing aging temperature. Hence, both nonequilibrium and equilibrium temperature shift factors can be calculated from the DSC data. Good agreement is observed between the equilibrium temperature shift factors obtained from the creep and DSC data. The temperature dependence of the nonequilibrium temperature shift factors is found to be an order of magnitude smaller than that of the equilibrium shift factors. The time scales to reach equilibrium for enthalpy and for mechanical measurements are found to be the same within experimental error. © 1995 John Wiley & Sons, Inc.     

Distribution of melamine in polyester–melamine surface coatings cured under nonisothermal conditions

The influence of experimental cure parameters on the diffusion of reactive species in polyester–melamine thermoset coatings during curing has been investigated with X‐ray photoelectron spectroscopy and attenuated total reflectance Fourier transform infrared. The diffusion of melamine plays a vital role in the curing process and, therefore, in the ultimate properties of coatings. At a low (<20%) hexamethoxymethylmelamine (HMMM) crosslinker concentration, the matrix composition is uniform, but at high HMMM concentrations, excess HMMM rapidly segregates to the air–coating interface. The rate of migration is governed by the difference in the surface free energies of polyester and HMMM and the concentration gradient of HMMM between the bulk and the surface. An increased rate of energy absorption also increases the rate of migration of HMMM to the surface. A physical model has been proposed to explain this surface segregation phenomenon in terms of cocondensation and self‐condensation reactions. It suggests that an appropriate amount of melamine can be segregated on the surface and allowed to self‐condense to form a desired thickness of a melamine topcoat through the control of the binder composition and cure conditions. This technique can be implemented to apply a melamine topcoat during cure. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 83–91, 2004     

Feasibility Exploration of Laser‐based Techniques for Characterization of a Flashing Jet

Two‐phase flows hold an interest in many areas of science and engineering. In the safety field, one such topic is the accidental release of flammable and toxic pressure‐liquefied gases. In case of such a release, a flashing vapor explosion takes place resulting in a very dense two‐phase cloud. If the released substance is flammable, this cloud can be combustible and can lead to deflagration or detonation. For understanding the source processes of flashing and risk assessment, data related to cloud characteristics (i.e. droplet size, velocity etc.) is needed especially in the near region of the release. Due to the non‐equilibrium nature of the near field regions accurate data measurement is not possible with intrusive techniques. Therefore, laser‐based optical techniques (like Particle Image Velocimetry (PIV), Particle Tracking Velocimetry and Sizing (PTVS), Phase Doppler Anemometry (PDA) etc.) present the only possibility to obtain information for particle diameter and velocity evolution in this harsh environment.     

Unexpected end‐groups of poly(acrylic acid) prepared by RAFT polymerization

Low‐molecular‐weight poly(acrylic acid) (PAA) was synthesized by reversible addition fragmentation chain transfer polymerization with a trithiocarbonate as chain‐transfer agent (CTA). With a combination of NMR spectroscopy and matrix‐assisted laser desorption/ionization time‐of‐flight mass spectrometry, the PAA end‐groups of the polymer were analyzed before and after neutralization by sodium hydroxide. The polymer prior to neutralization is made up of the expected trithiocarbonate chain‐ends and of the H‐terminated chains issued from a reaction of transfer to solvent. After neutralization, the trithiocarbonates are transformed into thiols, disulfides, thiolactones, and additional H‐terminated chains. By quantifying the different end‐groups, it was possible to demonstrate that fragmentation is the rate limiting step in the transfer reaction. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5439–5462, 2004     

UV curing of a novel resin derived from poly(ethylene terephthalate)

The synthesis and characterization of photopolymerizable unsaturated polyester resins based on PET waste are described. The resins came from a depolymerization process based on the glycolysis of PET by diethylene glycol (DEG). Different molecular weights of glycolysates were synthesized. Then, the latter was functionalized by a methyl hemiester of maleic acid to obtain unsatured α,ω‐bismaleate PET oligomers. In the presence of an electron donor monomer, such as triethylene glycol divinyl ether, these electron acceptor oligomers were copolymerized by way of charge‐transfer complexes under UV irradiation. The reaction was monitored in situ by real‐time IR spectroscopy to study the kinetics of photopolymerization. This one was studied in relation with the physical and chemical characteristics of oligoesters and the composition of mixtures containing divinyl ethers. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1324–1335, 2007     

Fast switching anisotropic networks obtained by in situ photopolymerization of liquid crystal molecules

Lightly cross-linked anisotropic networks with uniaxial and π/2 twisted orientations were produced by photopolymerization of monotropic mixtures containing liquid crystal mono and diacrylates. In this way the polymer backbone was immobilized and became decoupled from the motion of the mesogenic side groups. The networks showed very good reversibility and even after becoming isotropic, upon cooling, the initial orientation was recovered. In the same way, in the presence of electric fields the mesogenic groups could be reoriented in the direction of the electric field, reverting back to the initial orientation on removal of the field at a rate comparable with those observed in the monomeric state. Combining viscoelastic measurements with the dielectric behaviour of the monomeric liquid crystal and the anisotropic network, a comparison between the internal and bulk rotational viscosities was also made.     

On the linear relaxation of a one-dimensional bonded fluid model

The linear relaxation of a one-dimensional bonded fluid model is studied in the dynamical mean field approximation at the pair level. The results are compared with simulation data. Relaxation at low temperatures shows a cooperative character that can be understood in terms of a simple diffusion picture.     

Parametric linear programming techniques for the indefnite quadratic programming problem

In this paper, we discuss a multiparametric technique for findinga global minimum for an indefinite quadratic programming problembased on the spectral decomposition of the matrix of the quadraticform. Special attention is given to the case where this matrixhas only rank 1, where the multiparametric linear program turnsout to be a single-parameter linear program. An extension ofthe traditional linear parametric procedure is introduced whichin general solves this problem efficiently. However, an exampleis presented showing that this technique may take an exponentialnumber of steps.     

Optimal repair-cost limit for a consumer following expiry of a warranty

This paper develops a methodology for obtaining the optimalrepair-cost limit for the repair-replace decision that a consumerfaces on the expiry of a product warranty, where the producthas been minimally repaired on failure during the warranty.Three cases are considered; (i) an exponentially distributedtime to failure with an arbitrary repair-cost distribution,(ii) an exponentially distributed time to failure with a uniformrepair-cost distribution, and (iii) a Weibull-distributed timeto failure with a beta-distributed repair cost. Numerical optimizationsare performed for the third case, and conclusions drawn as tothe sensitivity of the optimal repair-cost limit on the parametervalues of the distributions involved.