Determination of partition coefficient and analysis of nitrophenols by three‐phase liquid‐phase microextraction coupled with capillary electrophoresis

A three‐phase hollow fiber liquid‐phase microextraction method coupled with CE was developed and used for the determination of partition coefficients and analysis of selected nitrophenols in water samples. The selected nitrophenols were extracted from 14 mL of aqueous solution (donor solution) with the pH adjusted to pH 3 into an organic phase (1‐octanol) immobilized in the pores of the hollow fiber and finally backextracted into 40.0 μL of the acceptor phase (NaOH) at pH 12.0 located inside the lumen of the hollow fiber. The extractions were carried out under the following optimum conditions: donor solution, 0.05 M H₃PO₄, pH 3.0; organic solvent, 1‐octanol; acceptor solution, 40 μL of 0.1 M NaOH, pH 12.0; agitation rate, 1050 rpm; extraction time, 15 min. Under optimized conditions, the calibration curves for the analytes were linear in the range of 0.05–0.30 mg/L with r²>0.9900 and LODs were in the range of 0.01–0.04 mg/L with RSDs of 1.25–2.32%. Excellent enrichment factors of up to 398‐folds were obtained. It was found that the partition coefficient (K_a/d) values were high for 2‐nitrophenol, 3‐nitrophenol, 4‐nitrophenol, 2,4‐dinitrophenol and 2,6‐dinitrophenol and that the individual partition coefficients (K_org/d and K_a/org) promoted efficient simultaneous extraction from the donor through the organic phase and further into the acceptor phase. The developed method was successfully applied for the analysis of water samples.     

Investigating droplet separation efficiency in wire-mesh mist eliminators in bubble column

Effects of design parameters on performance of wire-mesh mist eliminators were experimentally investigated in 15 cm bubble column. The demisters performances were evaluated by droplet collection efficiency as a function of wide ranges of operating and design parameters. These parameters include: droplet size exiting the demister (250–380 μm), specific surface area (236–868 m²/m³), void fraction (97–98.3%), wire diameter (0.14–0.28 mm), packing density (130–240 kg/m³), and superficial gas velocity (0.109–0.118 m/s. All demisters were 15 cm in diameter with 10 cm pad thickness, made from 316L stainless steel layered type demister pad wires. Experiments were carried out using air–water system at ambient temperature and atmospheric pressure. The experimental data on the droplet removal efficiency were obtained using Malvern Laser Droplet Sizer. The removal efficiency was found to increase with the increasing the demister specific surface area, packing density, and superficial gas velocity. In contrast, the removal efficiency was found to increase with decreasing the demister void fraction and wire diameter. The separation efficiency is correlated empirically as a function of the design parameters. A good agreement was obtained between the measured values and the correlation predictions with ±5% accuracy.     

Rapid and direct determination of glyphosate,glufosinate, and aminophosphonic acid by online preconcentration CE with contactless conductivity detection

Rapid and direct online preconcentration followed by CE with capacitively coupled contactless conductivity detection (CE‐C⁴D) is evaluated as a new approach for the determination of glyphosate, glufosinate (GLUF), and aminophosphonic acid (AMPA) in drinking water. Two online preconcentration techniques, namely large volume sample stacking without polarity switching and field‐enhanced sample injection, coupled with CE‐C⁴D were successfully developed and optimized. Under optimized conditions, LODs in the range of 0.01–0.1 μM (1.7–11.1 μg/L) and sensitivity enhancements of 48‐ to 53‐fold were achieved with the large volume sample stacking‐CE‐C⁴D method. By performing the field‐enhanced sample injection‐CE‐C⁴D procedure, excellent LODs down to 0.0005–0.02 μM (0.1–2.2 μg/L) as well as sensitivity enhancements of up to 245‐ to 1002‐fold were obtained. Both techniques showed satisfactory reproducibility with RSDs of peak height of better than 10%. The newly established approaches were successfully applied to the analysis of glyphosate, glufosinate, and aminophosphonic acid in spiked tap drinking water.     

Synthesis,labeling and biodistribution of <Superscript>99m</Superscript>Tc-3-amino-2-quinoxalin-carbonitrile 1,4-dioxide in tumor bearing mice

3-Amino-2-quinoxalincarbonitrile 1,4-dioxide (AQCD) is a quinoxaline derivative, which was synthesized by condensation method. AQCD was labeled with ^99mTc with labeling yield above 90% investigated by paper chromatography. ^99mTc-AQCD was prepared using stannous chloride as reducing agent at pH 7 and 10 min reaction time. ^99mTc-AQCD should be freshly prepared, otherwise the yield significantly decreased after 15 min post labeling. Stability study of ^99mTc-AQCD reflected the short time stability of Biodistribution study of ^99 mTc-AQCD in tumor bearing mice reflected that its uptake in tumor sites in both ascites and solid tumor sites. This uptake of ^99mTc-AQCD in tumor sites was sufficient to radioimage the inoculated sites.     

Dynamic supported liquid membrane tip extraction of glyphosate and aminomethylphosphonic acid followed by capillary electrophoresis with contactless conductivity detection

A dynamic supported liquid membrane tip extraction (SLMTE) procedure for the effective extraction and preconcentration of glyphosate (GLYP) and its metabolite aminomethylphosphonic acid (AMPA) in water has been investigated. The SLMTE procedure was performed in a semi-automated dynamic mode and demonstrated a greater performance against a static extraction. Several important extraction parameters such as donor phase pH, cationic carrier concentration, type of membrane solvent, type of acceptor stripping phase, agitation and extraction time were comprehensively optimized. A solution of Aliquat-336, a cationic carrier, in dihexyl ether was selected as the supported liquid incorporated into the membrane phase. Quantification of GLYP and AMPA was carried out using capillary electrophoresis with contactless conductivity detection. An electrolyte solution consisting of 12 mM histidine (His), 8 mM 2-(N-morpholino)ethanesulfonic acid (MES), 75 μM cetyltrimethylammonium bromide (CTAB), 3% methanol, pH 6.3, was used as running buffer. Under the optimum extraction conditions, the method showed good linearity in the range of 0.01–200 μg/L (GLYP) and 0.1–400 μg/L (AMPA), acceptable reproducibility (RSD 5–7%, n = 5), low limits of detection of 0.005 μg/L for GLYP and 0.06 μg/L for AMPA, and satisfactory relative recoveries (90–94%). Due to the low cost, the SLMTE device was disposed after each run which additionally eliminated the possibility of carry-over between runs. The validated method was tested for the analysis of both analytes in spiked tap water and river water with good success.     

Reinforcement of natural rubber/high density polyethylene blends with electron beam irradiated liquid natural rubber-coated rice husk

Coating of rice husk (RH) surface with liquid natural rubber (LNR) and exposure to electron beam irradiation in air were studied. FTIR analysis on the LNR-coated RH (RHR) exposed to electron beam (EB) showed a decrease in the double bonds and an increase in hydroxyl and hydrogen bonded carbonyl groups arising from the chemical interaction between the active groups on RH surface with LNR. The scanning electron micrograph showed that the LNR formed a coating on the RH particles which transformed to a fine and clear fibrous layer at 20 kGy irradiation. The LNR film appeared as patches at 50 kGy irradiation due to degradation of rubber. Composites of natural rubber (NR)/high density polyethylene (HDPE)/RHR showed an optimum at 20–30 kGy dosage with the maximum stress, tensile modulus and impact strength of 6.5, 79 and 13.2 kJ/m², respectively. The interfacial interaction between the modified RH and TPNR matrix had improved on exposure of RHR to e-beam at 20–30 kGy dosage.     

The effect of anti-reflection coating of porous silicon on solar cells efficiency

Anti-reflection coatings of solar cells have been fabricated using different techniques. The techniques used include SiO₂ thermal oxidation, ZnO/TiO₂ sputtering deposition and porous silicon prepared by electrochemical etching. Surface morphology and structural properties of solar cells were investigated by using scanning electron microscopy and atomic forces microscopy. Optical reflectance was obtained by using optical reflectometer. I-V characterizations were studied under 80 mW/cm² illumination conditions. Porous silicon was found to be an excellent anti-reflection coating against incident light when it is compared with another anti-reflection coating and exhibited good light-trapping of a wide wavelength spectrum which produced high efficiency solar cells.     

Effect of replacing calcium oxide with calcium halide on crystallization and some physical properties of calcium vanadium phosphate glass ceramics

The effect of halide ions on density, electrical, magnetic and crystallization kinetics for (20X-50P₂O₅-30V₂O₅) mole% has been investigated, where X=CaO, CaF₂, CaCl₂ and CaBr₂. Halide ions reduce the glass transition temperature, crystallization temperature and activation energy of crystallization. Density, electrical conductivity and magnetic susceptibility increase while molar volume, glass thermal stability and interatomic distance between transition metal ions decrease as the halide ions replace the oxygen ions in these glasses.     

Direct current and impedance spectroscopic studies on MoO3 modified ZnPc/ITO Schottky diodes

We use experimental results of direct current and low signal impedance spectroscopy to investigate the conduction mechanism in organic semiconductor ZnPc. The experimental results demonstrate an increase in current and holes mobility by the introduction of a thin MoO₃ film at the ITO/ZnPc interface. This significantly improves the device performance. The improvement is explained in terms of the reduction in the effective barrier for charge transfer from ZnPc to ITO.