Ce偶-偶同位素低激发态性质的IBM2描述

通过考虑同类核子相干对间的四极相互作用，在IBM2中对Ce偶－偶同位素^128Ce-^138Ce的低激发态能谱和E2跃迁几率及分支比进行了理论分析，计算结果有效地改善了IBM中这些核的γ带能谱的Staggering现象描述，与实验观察到的低激发态结果基本一致。     

Stationary Intensity Distribution of Single-Mode Laser Driven by Additive and Multiplicative Colored Noises with Colored Cross-Correlation

Applying the approximate Fokker-Planck equation we derived, we obtain the analytic expression of thestationary laser intensity distribution Pst(Ⅰ) by studying the single-mode laser cubic model subject to colored cross-correlation additive and multiplicative noise, each of which is colored. Based on it, we discuss the effects on the stationarylaser intensity distribution Pst(Ⅰ) by cross-correlation between noises and “color“ of noises (non-Markovian effect) whenthe laser system is above the threshold. In detail, we analyze two cases: One is that the three correlation-times (i.e.the self-correlation and cross-correlation times of the additive and multiplicative noise) are chosen to be the same value(τ1 = τ2 = τ3 = τ). For this case, the effect of noise cross-correlation is investigated emphatically, and we detect thatonly when λ≠ 0 can the noise-induced transition occur in the Pst(Ⅰ) curve, and only when τ≠ 0 and λ≠ 0, can the“reentrant noise-induced transition“ occur. The other case is that the three correlation times are not the same value,τ1 ≠τ2 ≠τ3. For this case, we find that the noise-induced transition occurring in the Pst (Ⅰ) curve is entirely differentwhen the values of τ1, τ2, and τ3 are changed respectively. In particular, when τ2 (self-correlation time of additivenoise) is changing, the ratio of the two maximums of the Pst(Ⅰ) curve R exhibits an interesting phenomenon, “reentrantnoise-induced transition“, which demonstrates the effect of noise “color“ (non-Markovian effect).     

一个素变数丢番图不等式

本文证明了如果1相似文献   

HL-2A װ��MW ������������ϵͳ��˿��Դ�����������

The main circuit topology, control hardware and control sequence of the cathode filament power supply for the HL-2A neutral beam heating system was introduced. Feedback control simulation of main circuit of filament power supply is carried out through MATLAB simulation software. It is found that the ripple factor is about 1%when the current is about 1000A, and the ripple coefficient increases to 3% when the current drops to 200A. Without the AC filter reactor in series L₁ and parallel harmonic filter LC in the low level control cabinet, the output current ripple coefficient becomes larger obviously. It shows that L₁ and LC not only absorb harmonic current, but also filter the chopper waveform after AC voltage regulation to make the output waveform smoother.     

两个级联型三能级原子受激辐射的非线性性质

本文研究了两个级联型三能级原子同单模腔场的非线性相互作用,研究表明:在激发场场强达到一定阈值以后,两个原子的合作辐射效应变成同步辐射,即多原子系统在一定阈值条件下可以有组织成相当于一个大原子的系统,而产生同步有序辐射。同时,由于这种同步辐射效应,两原子系统的受激辐射的二阶相干度相对于单原子系统的要大,即聚束效应强而反聚束效应弱。另外,两原子系统由于多光子过程的加强而有更深的压缩效应,此时要求的激发场场强也比单原子系统的要强。     

STUDIES ON CHARGE TRANSFER POLYMERIZATION——POLYMERIZATION OF ACRYLONITRILE INITIATED WITH PHENYL HYDRAZINE AND ITS DERIVATIVES

The photopolymerization of acrylonitrile (AN) initiated with phenyl hydrazine (PHZ) and its derivatives has been studied. The initiator exponent and monomer exponent were determined from the kinetic investigation to be 0.66th and 2.1th respectively and the overall activation energy was 33.4KJ/mol for the PHZ-AN system. Spectral analysis and other data indicate that a charge transfer complex between PHZ as a donor and AN as an aceeptor is formed. The initiation mechanism was proposed.     

Rheological Behavior for Mica-filled Polypropylene Composite Melts

The study on rheological properties of a series of mica-filled polypropylene (PP) composites was carried out. The influence of surface-treatment of mica particles on dynamic rheological behavior of the composites were dealt with. The viscosity (η) and dynamic modulus ( G‘ ) of the composite melts were higher than those of PP matrix, especially those for systems treated with silane, which was attributed to the interfacial adhesion enhancement. However, surface-treatment of mica by titanate resulted in lower η and G‘, as compared with the treatment by silane. The reason for this is believed to be the formation of the mono-molecular layer on the mica surface.     

透极远红外光学材料制备及性能研究

在一定的温度、压力等条件下,采用有机材料(聚四氟乙烯)和无机晶体(KBr、CsI),通过热合技术研制出样品几何尺寸为Φ20mm×3-5mm、透射波段分别为15-38μm(PE-KBr)和15-60μm(PE-CsI)的透极远红外复合光学材料。抗腐蚀性能测试结果表明,材料耐强酸、强碱及部分有机溶剂。机械性能分析表明材料在小于115℃范围内可安全使用。极远红外透过率测试结果表明,在1-15μm波段,平均透过率小于15%,15-38μm和15-60μm极远红外波段,平均透过率大于50%,并对影响材料透过率的因素进行了分析。     

全合成法光纤预制棒制造研究

介绍了一种全新的全合成法G.655和G.656光纤制造工艺,详细分析了该工艺中芯层折射率差Δ0、芯层厚度a、第二包层的折射率差Δ2、第二包层的厚度c2等结构参量与光纤光学性能的关系.结果表明,制造该两种光纤时,Δ0应在0.012 0～0.015 5之间,Δ2应在0.014 0～0.023 0之间,a应在2.8～3.2 μm之间,c2应在满足截止波长的要求下尽可能小.