Milling of Organic Solids in a Jet Mill. Part 2: Checking the Validity of the Predicted Rate of Breakage Function

The particle size distribution of fine chemicals in the solid state, like active pharmaceutical ingredients, is often a critical parameter. To achieve the desired particle size distribution, milling of such materials is usually the method of choice. Since these chemicals are often scarcely available, experimental optimization of milling is not possible. Therefore, a model to predict the milling conditions has been developed. The model estimates the rate of breakage function, and needs mechanical properties like hardness and yield strength as input to calculate the rate of breakage function. This paper attempts to check the validity of the model by a series of experiments. A comparison of the experimental results with the outcomes of the model using five different model compounds has been performed. It appears that the rate of breakage function can be estimated by: The model is able to rank the compounds by degree of fracture as an effect of milling. It was also possible to perform a quantitative prediction of the impact of milling pressure on the milling behavior. Finally, it appeared that the prediction of the large particles in the distribution was significantly better than small ones. Because the oversized material is usually the most critical parameter, the conclusion is that the model has acceptable practical applicability.     

A combinatorial approach toward the generation of ambiphilic peptide-based inhibitors of protein:geranylgeranyl transferase-1

A combinatorial synthesis of oligopeptide analogues and their evaluation as protein:geranylgeranyl transferase inhibitors is presented. The combinatorial strategy is based on the random mutation, in each new generation, of one of any of the four amino acid building blocks of which the most effective compounds of the previous generation are assembled. In this way, a progressive improvement of the average inhibitory activity was observed until the fifth generation. The most active inhibitors were found to inhibit PGGT-1 in the low micromolar range (IC(50): 3.8-8.1 microM).     

A practical synthesis of gramicidin s and sugar amino Acid containing analogues

A practical gram-scale and high-yielding synthesis of the antimicrobial peptide gramicidin S is presented. An Fmoc-based solid-phase peptide synthesis protocol is employed for the generation of the linear decapeptide precursor, which is cyclized in solution to afford the target compound. The versatility of our method is demonstrated by the construction of eight gramicidin S analogues (15a-h) having nonproteinogenic sugar amino acid residues (4-7) incorporated in the turn regions.     

Alkylated sugar amino acids: a new entry toward highly functionalized dipeptide isosters

[reaction: see text] Novel highly functionalized dipeptide isosters are synthesized via a diastereoselective alkyl/arylation protocol of a glucose-derived (R)-tert-butanesulfinylimine. One of these novel sugar amino acid derivatives, a D-Ala-Ser/Thr isostere, was applied in a peptide synthesis protocol to afford a cyclic tetramer.     

Synthesis of bridged sugar amino acids: a new entry into conformationally locked δ- and ε-amino acids

The synthesis of three methylene bridged sugar amino acids is described. Key transformations in the synthetic strategy are a CO-insertion on fully protected ribose, an aldol condensation with formaldehyde and an oxetane forming cyclisation step. A novel Leu-enkephalin analogue containing the δ-SAA 1 was prepared using standard solution phase peptide chemistry.     

Tomography of dispersive media

When waves propagate through layered structures, the phase velocity is frequency dependent (dispersive). If one wants to reconstruct the velocity variations in this medium, conventional traveltime-based tomographic methods cannot be used, since each frequency component has a different traveltime. A tomographic method is presented for reconstructing the phase velocity of guided waves in laterally varying media. The dispersive character of guided waves is explicitly accounted for by using a phase-based error criterium instead of "picked" traveltimes. Phase velocity and source waveform can be reconstructed to within a few percent, and the algorithm is shown to be robust in the presence of interference noise. When applied to seismic field data, the reconstructed phase velocity field correlates well with the topography of the area.     

Structure determination of the two-domain ( 1x4) anatase TiO2(001) surface

The reconstructed anatase TiO2(001) surface has been investigated by low-energy electron diffraction (LEED), x-ray photoelectron spectroscopy (XPS), and angle-resolved mass spectroscopy of recoiled ions (AR-MSRI). Prior investigations have observed or considered only a (1x1) unreconstructed termination for this surface with no detailed structural analysis. Our LEED results indicate a previously unobserved two-domain (1x4) reconstruction after sputtering and annealing the (1x1) surface. The XPS data for this reconstruction indicate the presence of only Ti4+. Simulations of the AR-MSRI experimental data indicate a best fit for a microfaceted surface, revealing both (103) and (1;03) surface planes.     

Intense picosecond X-Ray pulses from laser plasmas by use of nanostructured "Velvet" targets

We describe the optical, radiative, and laser-plasma physics of a new type of nanostructured surface especially promising as a very high absorption target for high-peak-power subpicosecond laser-matter interaction. This oriented-nanowire material, irradiated by 1 ps pulses at intensities up to 10(17) W cm(-2), produces picosecond soft x-ray pulses 50x more efficiently than do solid targets. We compare this to "smoke" or metallic clusters, and solid nanogroove-grating surfaces; the "metal-velvet" targets combine the high yield of smoke targets with the brief emission of grating surfaces.