On the Solvent‐free Structure of a Jäger‐type Cobalt(II) N2O2‐Chelate Complex

A combined synchrotron X‐ray and density functional theory (DFT) study on the structure of a Jäger‐type N₂O₂ chelate complex was carried out. The ethoxy‐substituted bis(3‐oxo‐enaminato)cobalt(II) complex ( 1 ) was an original sample from the laboratory of the late Professor Ernst‐G. Jäger (University of Jena, Germany). Single‐crystal X‐ray analysis revealed essentially flat molecules of 1 , which are unsolvated and coordinatively unsaturated. The DFT calculations on the isolated molecule predict a planar structure for the non‐hydrogen atoms, which is a local minimum on the energy surface. The crystal packing is achieved through off‐set stacking (staircase arrangement), resulting in a herringbone pattern in the space group P2₁2₁2₁. The structure of 1 is compared to known structures of related bis(3‐oxo‐enaminato)cobalt(II) complexes ( 2 – 4 ). Original bulk material of 1 was investigated by scanning electron microscopy (SEM), powder X‐ray diffraction (PXRD), melting point determination, and infrared (IR) spectroscopy.     

Recrystallization of 223Ra with barium sulfate

In this work, the kinetics of barium sulfate recrystallization has been studied in acidic 0.01 mol dm^?3 sodium sulfate solution using ²²³Ra and ¹³³Ba tracers at very low total radium concentration, i.e. less than 10^?13 mol dm^?3. It was found that the system follows the homogeneous recrystallization model and that recrystallization rates, inferred by the decrease of ²²³Ra and ¹³³Ba in the aqueous solution, are fast. Therefore, even at very low concentrations, below the solubility limit, radium will be retained by barium sulfate—a mineral present in the deep underground repository.     

A new reflector structure for facility thermalizing D–T neutrons

A facility for thermalization of fast neutrons (14.2 MeV) emitted by compact deuterium–tritium (D–T) neutron generators (NGs) for thermal neutron activation analysis is proposed. Its final design is based on Monte Carlo calculations (MCNP5). To maximize the ratio between the thermal neutron flux and the total neutron flux and simultaneously to ensure the highest possible value of the thermal neutron flux at the output surface, the facility should consist of a two-layer reflector [tungsten (W)—the inner part, molybdenum—the outer part], a two-layer multiplier (W followed by lead), a moderator (polyethylene followed by magnesium fluoride) and a collimator (molybdenum and nickel near the output surface). For the D–T NG producing the maximum available neutron yield 10¹⁵ n s^?1, the facility provides the thermal neutron flux 2.0 × 10¹¹ n cm^?2 s ^?1 and a slightly higher fast neutron flux 2.3 × 10¹¹ n cm^?2 s^?1. To improve the ratio of the thermal neutron flux to the fast neutron flux (above 2.7) an addition of a silicon layer to the moderator and especially a proper adjustment and a threefold increase of the multiplier thickness is necessary.     

Development of a method for the determination of 93Zr and 94Nb in radioactive waste using TEVA® resin

The behaviour of ⁹⁵Zr and ⁹⁵Nb isotopes on TEVA^® resin column was studied. The influence of hydrofluoric, hydrochloric, oxalic and sulphuric acids on the separation and chemical yield of zirconium and niobium was tested. The method is suitable for the separation of ⁹³Zr and ⁹⁴Nb isotopes from hydrofluoric, hydrochloric and sulphuric acid by using different concentrations of the acid for the load or elutes solutions. Samples from reactor and fuel assemblies such as the control-rod connection rod, shielding/absorber parts of fuel rods, neutron in-core measurement channels, pressure vessel basic construction material and internal cladding, core barrel and reactor protection tube unit were analysed.     

Monitoring bisphenol A and estrogenic chemicals in thermal paper with yeast-based bioreporter assay

Bioluminescent Saccharomyces cerevisiae yeast-based bioreporters were used to monitor bisphenol A and other estrogenic chemicals in thermal paper samples collected mainly from Finland on two occasions in 2010/2011, and 2013. The bisphenol A-targeted (BPA-R) and the human oestrogen receptor (hERα) bioreporters were applied to analyse both non-treated and extracted paper samples. Bisphenol A was readily bioavailable to the yeast bioreporters on the non-treated paper samples without any pre-treatment. Detected concentrations ranged from a detection limit of 9–142 μg/g to over 20 mg/g of bisphenol A equivalents in the thermal papers. Low bisphenol A like activities were detected in many samples, and were considered to be caused by residual bisphenol A or other types of bisphenols, such as bisphenol S. Most of the thermal paper samples were toxic to the yeast bioreporters. The toxicity did not, however, depend on the bisphenol A concentration of the samples. The yeast bioreporters were demonstrated to be a robust and cost-efficient method to monitor thermal paper samples for their bisphenol A content and estrogenicity. Thermal paper was considered as a potential BPA source for both human exposure and environmental emission.     

Development and characterization of a small electromembrane extraction probe coupled with mass spectrometry for real-time and online monitoring of in vitro drug metabolism

A small and very simple electromembrane extraction probe (EME-probe) was developed and coupled directly to electrospray ionization mass spectrometry (ESI-MS), and this system was used to monitor in real time in vitro metabolism by rat liver microsomes of drug substances from a small reaction (incubation) chamber (37 °C). The drug-related substances were continuously extracted from the 1.0 mL metabolic reaction mixture and into the EME-probe by an electrical potential of 2.5 V. The extraction probe consisted of a 1-mm long and 350-μm ID thin supported liquid membrane (SLM) of 2-nitrophenyl octyl ether. The drugs and formed metabolites where extracted through the SLM and directly into a 3 μL min^?1 flow of 60 mM HCOOH inside the probe serving as the acceptor solution. The acceptor solution was directed into the ESI-MS-system, and the MS continuously monitored the drug-related substances extracted by the EME-probe. The extraction efficiency of the EME-probe was dependant on the applied electrical potential and the length of the SLM, and these parameters as well as the volume of the reaction chamber were set to the values mentioned above to avoid serious depletion from the reaction chamber (soft extraction). Soft extraction was mandatory in order not to affect the reaction kinetics by sample composition changes induced by the EME-probe. The EME-probe/MS-system was used to establish kinetic profiles for the in vitro metabolism of promethazine, amitriptyline and imipramine as model substances.