Dynamic Surface Elasticity of Polyelectrolyte/Surfactant Adsorption Films at the Air/Water Interface: Carboxylmethylchitosan and Cetyltrimethylammonium Bromide

The dynamic surface elasticity of the solution of carboxymethylchitosan (CMCH) and cetyltrimethylammonium bromide (C₁₆TAB) was measured as a function of the surfactant concentration and the surface age by the oscillating drop method. The results showed that the surface layer of the CMCH/C₁₆TAB solution transformed from loose to structured with the increase in the surfactant concentration. The surface elasticity versus the surface pressure curve during the adsorption showed different features at different surfactant concentration ranges, which was connected with the structural transformation of the surface layer. Our results show that the measurement of dynamic surface dilational properties is a powerful tool for studying the surface kinetics, which is helpful for dealing non-equilibrium systems in industry.     

Redispersibility of Acrylate Polymer Powder and Stability of Its Reconstituted Latex

The acrylate redispersible polymer powder (RPP) was produced from acrylate latex via spray drying, which was synthesized by latex polymerization with the configuration of soft core and hard shell. The powder's redispersibility and stability of its reconstituted latex were achieved through incorporating monomer methacrylic acid (MAA), which has functional carboxyl group and can provide an ionization effect in alkaline range. The influence of pH value and MAA amount on the redispersibility and stability were studied. The stabilization mechanism for reconstituted latex was also investigated. The acrylate RPP has good redispersibility at MAA of 4–5% and pH values between 9.0 and 10.0. The reconstituted latex is stable at these conditions due to high zeta potential and strong electrostatic repulsion force.     

Study on Influencing Factors of Chemical Flooding for Heavy Oil

Alkali and alkali/surfactant displacing agents are designed for two kinds of heavy oil. Results of emulsifying capacity, dynamic interfacial tension (IFT) and water-wet core flooding tests show that, although alkaline/surfactant systems exhibit better capacity in emulsification and IFT reduction, oil recovery values of alkaline/surfactant flooding are lower than those of alkaline flooding. Glass-etched micromodel tests further demonstrate that, when alkaline solution penetrates into the oil phase, water streams break into ganglia coating oil film. Water ganglia may be entrapped by narrow throats, consequently presenting a water-oil alternating slug flow. Similar water ganglia also appears in alkaline/surfactant flooding, however, water channeling along the pore surface occurs subsequently, resulting in its relatively lower oil recovery.     

DETERMINATION OF LONG-TERM STABILITY OF VITAMIN E EMULSION AND FORMATION OF MICROEMULSIONS BY USING LASER LIGHT SCATTERING AND UV ABSORPTION MEASUREMENTS

This paper presents methods of determining the long-term stability of vitamin E emulsion and formation of microemulsions. Several emulsion systems formed by using anionic, zwitterionic and cationic surfactants have been studied in the presence and absence of NaCI. Several conclusions can be drawn: (1) by using UV absorption and particle size measurements, one may be able to predict the long-term stability of an emulsion or the possibility of forming a microemulsion by measuring the initial properties of an emulsion, (2) in order to form a stable vitamin E emulsion or microemulsion, the initial properties of the emulsion should have the following features : (a) the particle size is ≤ 200 nm, (b) the surfactant system has a saturation value ≥ 1 and (c) the surfactant system can dissolve a substantial amount of vitamin E without causing an increase of the emulsion droplet size and (3) the saturation value and the stability of many vitamin E emulsion systems can be increased by adding an optimum amount of NaCI.     

Synthesis and Characterization of Multi‐Walled Carbon Nanotube/Polythiophene Composites

Multi‐walled carbon nanotube (MWCNT)/polythiophene (PTh) composites have been prepared by in situ chemical oxidative polymerization. PTh is synthesized onto the sidewalls of the MWCNTs, which play a role as hard templates for PTh to produce one‐dimensional nanostructures. The morphology and structures of the MWCNT/PTh composites are characterized by High‐resolution transmission electron microscopy, x‐ray diffraction, and Fourier transform infrared spectrometry. Their electrical property and thermal stability are determined using vector network analyzer and thermal gravimetric analyzer. Moreover, the mechanism of MWCNT/PTh nanowire formation is described. The studies show that the composites are nanowires with core‐shell structure, in which the outer shells and inner cores are formed by PTh and MWCNTs, respectively. The addition of MWCNTs does not change the backbone structure of PTh and affect the amorphous condition of PTh very slightly, however, it improves the electrical conductivity and thermal stability of PTh.     

Chitosan‐Based Glucose Oxidase Electrodes Enhanced by Silver Nanoparticles

Silver nanoparticles enhanced glucose oxidase electrodes were prepared on the basis of chitosan matrix. The enzyme electrodes exhibited high sensitivity and excellent response performance to glucose with a linear range from 1×10^?6 to 8×10^?3 mol · L^?1. And the time reaching the steady‐state amperometric response was less than 5 seconds. The inhibition percentage of this enzyme electrode against copper ions concentration was linear ranging from 1.2×10^?6 to 5×10^?5 mol · L^?1. These properties of enzyme electrodes are probably due to the excellent electron transfer of silver nanoparticles and the orientation of glucose oxidase molecule.     

A Facile Method for Preparation of Superhydrophobic Surfaces with Poly(furfuryl Alcohol)/PTFE Composites

A stable superhydrophobic surface have been fabricated with poly(furfuryl alcohol) (PFA)/polytetrafluoroethylene (PTFE) composite coatings on steel substrates by using a facile method. The observation of field emission scanning electron microscopy revealed that the hierarchical microstructures formed on the surfaces are controlled by varying the curing temperature. This method can be easily operated on substrates of steel, therefore is readily developed to other engineering metal substrates such as aluminum, copper, etc.     

仿生制备有机-无机复合微囊固定化葡萄糖氧化酶

将层层自组装技术与仿生矿化技术相结合,由聚苯乙烯磺酸钠、聚二甲基二烯丙基氯化铵和二氧化硅成功制备(聚苯乙烯磺酸钠-聚二甲基二烯丙基氯化铵)₂-二氧化硅复合微囊.采用扫描电子显微镜、红外光谱和热重对微囊的形貌和化学结构进行了表征.以该复合微囊作为理想载体固定化葡萄糖氧化酶.结果表明,固定于复合微囊中的葡萄糖氧化酶的热稳定性、pH稳定性、操作稳定性得到了提高;在最适条件下,复合微囊固定化葡萄糖氧化酶的酶活回收率为72.85%,米氏常数是游离葡萄糖氧化酶的2.21倍.复合微囊在化学/生物催化、药物/基因传递系统和生物传感器应用方面具有一定的潜能.     

IN SITU OBSERVATION OF MELTING AND CRYSTALLIZATION BEHAVIORS OF POLY(ε-CAPROLACTONE) ULTRA-THIN FILMS BY AFM TECHNIQUE

The melting and crystallization behaviors of poly(ε-caprolactone) (PCL) ultra-thin films with thickness from 15 nm to 8 nm were studied by AFM technique equipped with a hot-stage in real-time. It was found that melting can erase the spherulitic structure for polymer film with high thickness. However, annealing above the melting point can not completely erase the tree-like structure for the thinner polymer film. Generally, the structure formation of thin polymer films of PCL is controlled not only by melting and crystallization but also by dewetting during thermal annealing procedures, and dewetting predominates in the structure formation of ultra-thin films. However, the presence of tree-like morphology at 75 °C may be due to the strong interaction between PCL and mica surface, which may stick the PCL chains onto the mica surface during thermal annealing process. Moreover, the growth of the dendrites was investigated and it was found that crystallization is followed from a dewetted sample, and the branches did not grow with the stems. The crystallization of polymer in the ultra-thin films is a diffusion-controlled process. Both melting and crystallization behaviors of PCL in thin films are influenced by film thickness.     

Crowding effect induced phase transition of amphiphilic diblock copolymer in solution

The crowding agent induced phase transition of amphiphilic block copolymers in solution was explicitly considered. The influence of the size and the volume fraction of the crowding agent on the phase separation of amphiphilic diblock copolymers is investigated by using self-consistent field theory (SCFT) method. The concentration of the disorder to order transition of the block copolymer decreases when the size of the crowding agent is larger than that of the solvent. The higher volume fraction of the crowding agent will induce the transition of the block copolymer from disorder to order state at a lower concentration. The relation between the size and the volume fraction of the crowding agent is elucidated. When the size of the crowding agent is larger, its volume fraction of the disorder to order transition of the block copolymer will be lower. The conformation of the crowding agent considered as a polymer chain is also studied and compared.