连续一级反应的热动力学研究

本文把时间比法引入热动力学研究,建立了连续一级反应的热动力学研究法,并用来研究了一个连续反应体系的热动力学,验证了该方法的正确性.     

Self-gelatinizable copolymer immobilized glucose biosensor based on prussian blue modified graphite electrode

A novel poly(vinyl alcohol) grafting 4-vinylpyridine self-gelatinizable copolymer was adapted to immobilize glucose oxidase. The reduction of hydrogen peroxide (H2O2) was detected at a Prussian Blue (PB) modified graphite electrode. A stable and sensitive glucose amperometric biosensor is described. The copolymer is a good biocompatible polymer in which the glucose oxidase retains high activity. Moreover, the copolymer can adhere firmly to the inorganic PB membrane. The sensor showed an apparent Michaelis-Menten constant of 18 +/- 0.2 mM and a maximum current density of 1.14 microA cm-2 mM-1. The linear range is from 5 microM to 4.5 mM glucose and the detection limit is 0.5 microM glucose. The catalytic efficiency of PB for the reduction of H2O2 is higher than that for the oxidation of H2O2. Glucose concentrations in serum samples from healthy persons and diabetic patients were determined using the sensor. The results compared well with those provided by the hospital using a spectroscopy method.     

TiO2 sol-gel derived amperometric biosensor for H2O2 on the electropolymerized phenazine methosulfate modified electrode

A novel hydrogen peroxide biosensor was developed based on the immobilization of horseradish peroxidase (HRP) in a TiO(2) sol-gel matrix on an electropolymerized phenazine methosulfate (PMS) modified electrode surface. Such membranes are of interest due to their high surface area, biological compatibility, and ease of fabrication. HRP entrapped in the TiO(2) matix was stable and retained its activity to a large extent. Cyclic voltammetry and amperometric measurements were employed to demonstrate the feasibility of electron transfer between immobilized HRP and the glassy carbon electrode via electropolymerized PMS. The influence of various experimental parameters such as operating potential, pH, temperature, and stability was investigated for optimum analytical performance. The biosensor provided a wide linear calibration range from 4.0x10(-6) M to 1.0x10(-3) M, with a detection limit of 8.0x10(-7) M at a signal-to-noise ratio of 3. The sensor retained 80% of its original activity after two months of operation.     

Simple interface for capillary electrophoresis-inductively coupled plasma atomic emission spectrometry

A simple interface has been developed to couple capillary electrophoresis (CE) to inductively coupled plasma atomic emission spectrometry (ICP-AES) for metal speciation. A concentric glass nebulizer with elongated tip is used as the CE-ICP interface. The CE capillary is the central tube of the nebulizer. A platinum wire is wrapped across the exit end of the CE capillary to provide electrical connection to the CE power supply. No sheath flow of buffer solution is needed. A simple cooling system has also been developed. A peristaltic pump circulates water through a plastic tube that encloses the section of the CE capillary between the CE instrument and the ICP spectrometer. Characteristics of the CE-ICP interface, e.g., elution time, nebulization and transport efficiency and peak broadening, versus carrier gas flow-rate have been studied. Comparisons to a previous design with the Pt electrode inserted into the end of the CE capillary are made where appropriate. The reproducibility (RSD) in ICP emission intensity of the system is <4%. Detection limits of Cr and Cu are approximately 5 ng/ml.     

Synthesis of fluorinated imines and carbodiimides from azides via aza-Wittig reaction

The Staudinger reaction of fluoroalkylazides were studied. A series of N-fluoroalkylimines were synthesized via aza-Wittig reaction of N-fluoroalkyliminophosphoranes. The N,N′-difluoroalkylated carbodiimide was also synthesized via the reaction of N-fluoroalkyliminophosphoranes with carbon dioxide or carbon disulfide.     

波束开角对多普勒测频结果的影响*

具有不同波束开角的声学多普勒测速设备未标定的测速结果存在偏差。基于水底椭圆散射模型研究了波束开角对声学多普勒测速结果的影响,对提高声学测速性能具有实际意义。水底椭圆散射模型下,足印上不同方位传播损失和散射强度存在差异,导致频谱不对称,测频结果偏小。利用不对称系数量化频谱不对称程度,若波束开角增大,方位不对称系数随之增大,测频偏差增大,推导了波束开角导致的测频偏差解析式。分析仿真和外场试验数据测频结果可知,不同多普勒频移下测频偏差和理论计算值相符,不同波束开角下实际测频偏差与理论公式计算的测频偏差均随波束开角增大而增大。     

Isolation of a carbon nanohoop with M(o)bius topology

Carbon nanohoop,a class of constrained molecular architecture consisting of linked arene units,has attracted considerable interest from both experimental and th...     

缓冲层ZnPc对有机电致发光器件特性的影响

本文研究了酞菁锌(ZnPc)薄膜的表面形貌及ZnPc薄膜作为缓冲层对有机电致发光器件(OLEDs)光电特性的影响.对比两组样品的AFM图像,ZnPc薄膜相比于ITO薄膜,其表面的岛面积较大,薄膜表面更连续平整,基本上覆盖了ITO膜表面针孔,减少了表面的缺陷.另外,ZnPc薄膜的岛分布均匀有序.使用ZnPc作为缓冲层的器件性能明显好于未使用ZnPc修饰的器件,在7.42V的驱动电压下的最大发光亮度达到1.428kcd/m2,在4.3V电压驱动下时,最大光功率效率为1.411m/W;而未使用缓冲层的器件在8V的驱动电压下达到最大发光亮度达到1.212kcd/m2,在5.5V电压驱动下时,最大光功率效率为0.931m/W.     

Preparation of Silica Aerogel/Resin Composites and Their Application in Dental Restorative Materials

As the most advanced aerogel material, silica aerogel has had transformative industrial impacts. However, the use of silica aerogel is currently limited to the field of thermal insulation materials, so it is urgent to expand its application into other fields. In this work, silica aerogel/resin composites were successfully prepared by combining silica aerogel with a resin matrix for dental restoration. The applications of this material in the field of dental restoration, as well as its performance, are discussed in depth. It was demonstrated that, when the ratio of the resin matrix Bis-GMA to TEGDMA was 1:1, and the content of silica aerogel with 50 μm particle size was 12.5%, the composite achieved excellent mechanical properties. The flexural strength of the silica aerogel/resin composite reached 62.9546 MPa, which was more than five times that of the pure resin. Due to the presence of the silica aerogel, the composite also demonstrated outstanding antibacterial capabilities, meeting the demand for antimicrobial properties in dental materials. This work successfully investigated the prospect of using commercially available silica aerogels in dental restorative materials; we provide an easy method for using silica aerogels as dental restorative materials, as well as a reference for their application in the field of biomedical materials.