A study of the precision and accuracy of peak quantification in comprehensive two-dimensional liquid chromatography in time

Simulated chromatographic data were used to determine the precision and accuracy in the estimation of peak volumes (i.e., peak sizes) in comprehensive two-dimensional liquid chromatography in time (LC × LC). Peak volumes were determined both by summing the areas in the second dimension chromatograms and by fitting the second dimension areas to a Gaussian peak. The Gaussian method is better at predicting the peak volume than the moments method provided there are at least three second dimension injections above the limit of detection (LOD). However, when only two of the second dimension signals are substantially above baseline, the accuracy and precision of the Gaussian fit method become quite poor because the results from the fitting algorithm become indeterminate. Based on simulations in which the modulation ratio (M_R = 4¹σ/t_s) and sampling phase (?) were varied, we conclude for well-resolved peaks that the optimum precision in peak volumes in 2D separations will be obtained when the M_R is between two and five, such that there are typically four to ten second dimension peaks recorded over the eight σ width of the first dimension peak. This sampling rate is similar to that suggested by the Murphy–Schure–Foley criterion. This provides an RSD of approximately 2% for the signal-to-noise ratio used in the present simulations. The precision of the peak volume of experimental data was also assessed, and RSD values were in the range of 4–5%. We conclude that the poorer precision found in the LC × LC experimental data as compared to LC may be due to experimental imprecision in sampling the effluent from the first dimension column.     

Effect of biaxial orientation on dielectric and breakdown properties of poly(ethylene terephthalate)/poly(vinylidene fluoride‐co‐tetrafluoroethylene) multilayer films

Polymer films with enhanced dielectric and breakdown properties are essential for the production of high energy density polymer film capacitors. By capitalizing on the synergistic effects of forced assembly nanolayer coextrusion and biaxial orientation, polymer multilayer films using poly(ethylene terephthalate) (PET) and a poly(vinylidene fluoride‐co‐tetrafluoroethylene) [P(VDF‐TFE)] copolymer were produced. These films exhibited breakdown fields, under a divergent field using needle/plane electrodes, as high as 1000 kV mm^?1. The energy densities of these same materials, under a uniform electric field measured using plane/plane electrodes, were as high as 16 J cm^?3. The confined morphologies of both PET and P(VDF‐TFE) were correlated to the observed breakdown properties and damage zones. On‐edge P(VDF‐TFE) crystals induced from solid‐state biaxial stretching enhanced the effective P(VDF‐TFE) layer dielectric constant and therefore increased the dielectric contrast between the PET and P(VDF‐TFE) layers. This resulted in additional charge buildup at the layer interface producing larger tree diameters and branches and ultimately increasing the breakdown and energy storage properties. In addition to energy storage and breakdown properties, the hysteresis behavior of these materials was also evaluated. By varying the morphology of the P(VDF‐TFE) layer, the low‐field dielectric loss (or ion migration behavior) could be manipulated, which in turn also changed the observed hysteresis behavior. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 882–896     

Preparation and evaluation of carbon coated alumina as a high surface area packing material for high performance liquid chromatography

The retention of polar compounds, the separation of structural isomers and thermal stability make carbonaceous materials very attractive stationary phases for liquid chromatography (LC). Carbon clad zirconia (C/ZrO₂), one of the most interesting, exhibits unparalleled chemical and thermal stability, but its characteristically low surface area (20–30 m²/g) limits broader application as a second dimension separation in two-dimensional liquid chromatography (2DLC) where high retentivity and therefore high stationary phase surface area are required. In this work, we used a high surface area commercial HPLC alumina (153 m²/g) as a support material to develop a carbon phase by chemical vapor deposition (CVD) at elevated temperature using hexane vapor as the carbon source. The loading of carbon was varied by changing the CVD time and temperature, and the carbon coated alumina (C/Al₂O₃) was characterized both physically and chromatographically. The resulting carbon phases behaved as a reversed phase similar to C/ZrO₂. At all carbon loadings, C/Al₂O₃ closely matched the unique chromatographic selectivity of carbon phases, and as expected the retentivity was increased over C/ZrO₂. Excess carbon – the amount equivalent to 5 monolayers – was required to fully cover the oxide support in C/Al₂O₃, but this was less excess than needed with C/ZrO₂. Plate counts were 60,000–76,000/m for 5 μm particles. Spectroscopic studies (XPS and FT-IR) were also conducted; they showed that the two materials were chemically very similar.     

Instantaneous gelation in coagulation dynamics

The coagulation equations are a model for the dynamics of cluster growth in which clusters can coagulate via binary interactions to form larger clusters. For a certain class of rate coefficients we prove that the density is not conserved on any time interval.Dedicated to Klaus Kirchgässner on the occasion of his sixtieth birthday     

The maximum degree in a random tree and related problems

Meir and Moon studied the distribution of the maximum degree for simply generated families of trees. We have sharper results for the special case of labelled trees. © 1994 John Wiley & Sons, Inc.