Comparison of standard addition and conventional isotope dilution mass spectrometry for the quantification of endogenous progesterone in milk

In this study, a standard addition–isotope dilution mass spectrometry (SA-IDMS) method for quantification of endogenous progesterone in milk has been described. The method validation results, linearity, limits of detection and quantification, recovery and uncertainty were fit for the purpose of assigning reference mass fractions to proficiency testing schemes. The developed technique was compared to the isotope dilution mass spectrometry (IDMS) method already existing in the laboratory. Analytical results of two milk samples were (1.377 ± 0.048) μg/kg and (4.457 ± 0.155) μg/kg by SA-ID-LC/MS method, while the results were (1.355 ± 0.019) μg/kg and (4.359 ± 0.059) μg/kg by ID-LC/MS, respectively. Since SA-IDMS was an effective quantitative method that overcame matrix effect, similar quantitative results from IDMS and SA-IDMS indicated that the quantification of progesterone in milk was barely influenced by matrix. Both IDMS and SA-IDMS could be used to assign reference mass fractions to progesterone in milk inter-laboratory proficiency testing schemes.     

Glutaraldehyde crosslinking of arabinoxylan produced from corn ethanol residuals

This study investigated the possibility of substituting petroleum-based polymers with biopolymers for films and paper coatings. Arabinoxylan (AX) was extracted from distillers’ grains, a low-value corn ethanol byproduct, and modified through crosslinking with glutaraldehyde (GA) which was made into films and paper coatings. The effects of degree of substitution (DS) on film and coating properties of GA cross-linked AX, referred to as GAX, were investigated. The GAX films had markedly higher tensile strength, approximately 3 times higher than the unmodified AX films at low DS, with higher DS causing a negative effect on the film tensile strength. Compared to unmodified AX coating, paper coated with GAX also had significantly higher tensile index, presumably due to high adhesion between the coating and paper interface. When used as a coating binder with calcium carbonate pigments, GAX showed comparable performance to polyvinyl alcohol, a common industrial binder, demonstrating the potential to be substituted for the petroleum-based paper coating binder.     

Effect of boundary representation on viscous,separated flows in a discontinuous-Galerkin Navier–Stokes solver

The effect of curved-boundary representation on the physics of the separated flow over a NACA 65(1)-412 airfoil is thoroughly investigated. A method is presented to approximate curved boundaries with a high-order discontinuous-Galerkin spectral element method for the solution of the Navier–Stokes equations. Multiblock quadrilateral element meshes are constructed with the grid generation software GridPro. The boundary of a NACA 65(1)-412 airfoil, defined by a cubic natural spline, is piecewise-approximated by isoparametric polynomial interpolants that represent the edges of boundary-fitted elements. Direct numerical simulation of the airfoil is performed on a coarse mesh and fine mesh with polynomial orders ranging from four to twelve. The accuracy of the curve fitting is investigated by comparing the flows computed on curved-sided meshes with those given by straight-sided meshes. Straight-sided meshes yield irregular wakes, whereas curved-sided meshes produce a regular Karman street wake. Straight-sided meshes also produce lower lift and higher viscous drag as compared with curved-sided meshes. When the mesh is refined by reducing the sizes of the elements, the lift decrease and viscous drag increase are less pronounced. The differences in the aerodynamic performance between the straight-sided meshes and the curved-sided meshes are concluded to be the result of artificial surface roughness introduced by the piecewise-linear boundary approximation provided by the straight-sided meshes.     

A statistical learning strategy for closed-loop control of fluid flows

This work discusses a closed-loop control strategy for complex systems utilizing scarce and streaming data. A discrete embedding space is first built using hash functions applied to the sensor measurements from which a Markov process model is derived, approximating the complex system’s dynamics. A control strategy is then learned using reinforcement learning once rewards relevant with respect to the control objective are identified. This method is designed for experimental configurations, requiring no computations nor prior knowledge of the system, and enjoys intrinsic robustness. It is illustrated on two systems: the control of the transitions of a Lorenz’63 dynamical system, and the control of the drag of a cylinder flow. The method is shown to perform well.     

Nonextensive thermodynamic relations based on the assumption of temperature duality

The nonextensive thermodynamic relations are expressed under the assumption of temperature duality, endowing the “physical temperature” and the “Lagrange temperature” in different physical senses. Based on this assumption, two sets of parallel Legendre transform structures are given. One is called “physical” set, and the other is called “Lagrange” set. In these two formalisms, the thermodynamic quantities and the thermodynamic relations are both liked through the Tsallis factor. Application of the two sets of the thermodynamic relations to the self-gravitating system shows that the heat capacity defined in the classical thermodynamics has no relevance to the stability of the system. Instead, the newly defined heat capacity can determine the stability of the system.     

Toward numerical simulations of fluid–structure interactions for investigation of obstructive sleep apnea

Obstructive sleep apnea (OSA) is a medical condition characterized by repetitive partial or complete occlusion of the airway during sleep. The soft tissues in the airway of OSA patients are prone to collapse under the low-pressure loads incurred during breathing. This paper describes efforts toward the development of a numerical tool for simulation of air–tissue interactions in the upper airway of patients with sleep apnea. A procedure by which patient-specific airway geometries are segmented and processed from dental cone-beam CT scans into signed distance fields is presented. A sharp-interface embedded boundary method based on the signed distance field is used on Cartesian grids for resolving the airflow in the airway geometries. For simulation of structure mechanics with large expected displacements, a cut-cell finite element method with nonlinear Green strains is used. The fluid and structure solvers are strongly coupled with a partitioned iterative algorithm. Preliminary results are shown for flow simulation inside the three-dimensional rigid upper airway of patients with obstructive sleep apnea. Two validation cases for the fluid–structure coupling problem are also presented.     

Influence of K<Subscript>2</Subscript>Ti<Subscript>6</Subscript>O<Subscript>13</Subscript> on dielectric and barrier properties of polymer

Polymer composite comprising polyvinylidene fluoride (PVDF) and potassium hexatitante (K₂Ti₆O₁₃) was synthesized by solution casting. The effect of K₂Ti₆O₁₃ on surface, thermal, and electrical properties of polymer composite were investigated. The addition of K₂Ti₆O₁₃ with polymer leads to thermal degradation and transition of polymer composite from semi-crystalline to amorphous phase. The optimum results of contact angle for different loading wt% of K₂Ti₆O₁₃ were directly correlated with the surface morphology. Our experimental results confirmed the incorporation of K₂Ti₆O₁₃ in polymer by SEM micrographs. The evaluated dielectric properties (ε' = 424; tan δ = 2.14 at 130 °C and 100 Hz frequency for 20 wt% loading of K₂Ti₆O₁₃) for polymer composite are higher in compared to pure polymer. The enhancement in dielectric constant and changing the surface properties of polymer composite can be used for the development of electrochemical storage device applications.