Evaluation of the calibration errors on cooling of a differential scanning calorimeter using different sets of standard metals

The temperature calibration on cooling of thermal analysis instruments is important for the accurate study of the non-isothermal crystallization kinetics of semi-crystalline polymers. In previous works, a methodology was proposed for performing the calibration on cooling of differential scanning calorimeters (DSCs) with standard metals, and the calibration errors were checked using transitions of high-purity liquid crystals. In this work, alternative, physically meaningful, procedures for carrying out the calibration on cooling are analyzed and validated. The calibration errors are evaluated also with liquid crystalline transitions, when the calibration is performed with standard metals, in a wide temperature range, and when due account is taken for the need of isothermal corrections to the temperature measurements. It is shown that any pair of standard metals may be used to calibrate on cooling, that the calibration errors increase for wider working temperature ranges and that, providing that certain conditions are fulfilled, both calibration procedures yield similar results.     

Immobilized pH gradient isoelectric focusing and immunoblotting for investigations of anti-Borrelia burgdorferi IgG antibodies.

Anti-Borrelia burgdorferi immunoglobulin G (IgG) responses in cerebrospinal fluid, serum, and joint fluid from Lyme disease patients were investigated by immobilized pH gradient (IPG) isoelectric focusing (IEF) in pH 4-10 and pH 4-7 gels. After focusing, the anti-B.-burgdorferi antibodies were blotted by affinity-driven transfer to antigen-coated polyvinylidene difluoride membranes (immunoblot) and the IgG antibodies were immunoenzymatically stained. IPG-IEF gels gave an excellent resolution of IgG and the immunoblot proved advantageous for the detection of anti-B. burgdorferi IgG antibodies. These antibodies, as judged from the electromigration characteristics, were found to contain oligoclonal as well as polyclonal subpopulations. This latter group included IgG antibodies that were inadequately resolved when separated by conventional carrier ampholyte IEF.     

Sol-gel ZrO2 coatings for chemical protection of stainless steel

ZrO₂ coatings deposited on 316 L stainless steel sheets were synthesized by sol-gel method using Zr(OC₃H₇)₄ as precursor and isopropanol, glacial acetic acid, and water as solvents for application with ultrasounds. Different solutions for dip-coating were prepared with compositions varying between 0.025 and 0.9 mol/dm³ of ZrO₂. X-ray diffraction shows that the films densified at 800°C are crystalline with a tetragonal structure. The thickness of the coatings varied from 0.35–0.75 m. The influence of the ZrO₂ coatings on the corrosion behavior of stainless steel substrates in aqueous NaCl was studied through potentiodynamic polarization curves at 1 mV/s. The values of the electrochemical parameters allow for an explanation of the role of the films in the increased resistance of steel against corrosion in moderately aggressive environments.     

Reagentless biosensor for isocitrate using one step modified Pt-Ir microelectrode

The Pt-Ir microelectrode modified through one step electropolymerization is proposed for the isocitrate amperometric biosensor construction. The enzyme (isocitrate dehydrogenase-ICDH), coenzyme (NADP(+)) and mediator (Meldola's Blue) were immobilized onto the microelectrode surface in one step from a PIPES buffer solution containing pyrrole. The optimized experimental conditions were 25 cycles of cyclic voltammetric in a solution containing 3.58 10(-5) mol l(-1) of mediator, 3.51 10(-4) mol l(-1) of coenzyme and 2.68 U ml(-1) of enzyme. In contrast to the biosensor for isocitrate reported in literature, just one enzyme was immobilized and no coenzyme addition in the solution of analysis was necessary. Catalytic currents were proportional to the isocitrate concentration between 7.7 10(-6) and 1.04 10(-4) mol l(-1), showing good repeatability. The detection limit of the proposed biosensor was 3.50 10(-6) mol l(-1), the response time was lower than 20 s, the lifetime was about 30 determinations and no significant interference of sugars and citric acid was verified. Orange juice samples were analysed by both methodology biosensor and spectrophotometric commercial kit, and the obtained results presented a good correlation. The data demonstrated that the developed biosensor is suitable for isocitrate determination in orange juice without matrix interferences.     

Solid-phase fluorescence spectroscopy for the determination of acetylsalicylic acid in powdered pharmaceutical samples

A rapid, simple and rugged procedure without requiring any prior sample treatment was developed for the determination of acetylsalicylic acid (ASA) in tablets formulations by solid-phase fluorescence spectroscopy. The method was carried out on powdered samples, consisting of an active substance dispersed in lactose, maize starch, talc and magnesium stearate. Previous knowledge of the sample bulk composition is needed for proper application of the method. Wavelengths for maximum excitation and emission were 288 and 318 nm, respectively, and the fluorescence intensity was linear with ASA concentration within the 50-170 mg g⁻¹ range. Detection and quantification limits were 2.2 and 7.3 mg g⁻¹, and the analytical frequency was 200 h⁻¹. For a typical sample, the relative standard deviation of results was estimated as 2.3% (n = 10). Accuracy was assessed by comparing the analytical results obtained with the proposed method with those related to a reference method recommended by British Pharmacopoeia: no differences between the methods were found at the 95% confidence level.     

Optimized determination of calcium in grape juice,wines, and other alcoholic beverages by atomic absorption spectrometry

This paper describes a study of the different methods of sample preparation for the determination of calcium in grape juice, wines, and other alcoholic beverages by flame atomic absorption spectrometry; results are also reported for the practical application of these methods to the analysis of commercial samples produced in Spain. The methods tested included dealcoholization, dry mineralization, and wet mineralization with heating by using different acids and/or mixtures of acids. The sensitivity, detection limit, accuracy, precision, and selectiviy of each method were established. Such research is necessary because of the better analytical indexes obtained after acid digestion of the sample, as recommended by the European Union, which advocates the direct method. In addition, although high-temperature mineralization with an HNO3-HCIO4 mixture gave the best analytical results, mineralization with nitric acid at 80 degrees C for 15 min gave the most satisfactory results in all cases, including those for wines with high levels of sugar and beverages with high alcoholic content. The results for table wines subjected to the latter treatment had an accuracy of 98.70-99.90%, a relative standard deviation of 2.46%, a detection limit of 19.0 microg/L, and a determination limit of 31.7 microg/L. The method was found to be sufficiently sensitive and selective. It was applied to the determination of Ca in grape juice, different types of wines, and beverages with high alcoholic content, all of which are produced and widely consumed in Spain. The values obtained for Ca were 90.00 +/- 20.40 mg/L in the grape juices, 82.30 +/- 23.80 mg/L in the white wines, 85.00 +/- 30.25 mg/L in the sweet wines, 84.92 +/- 23.11 mg/L in the red wines, 85.75 +/- 27.65 mg/L in the rosé wines, 9.51 +/- 6.65 mg/L in the brandies, 11.53 +/- 6.55 mg/L in the gin, 7.3 +/- 6.32 mg/L in the pacharán, and 8.41 +/- 4.85 mg/L in the anisettes. The method is therefore useful for routine analysis in the quality control of these beverages.     

Regioselective homogeneous hydrogenation of heteroaromatic nitrogen compounds by use of [RuH(CO)(NCMe)2(PPh3)2]BF4 as the precatalyst

Summary The complex [RuH(CO)(NCMe)₂(PPh₃)₂]BF₄ (1) is an efficient and regioselective catalyst precursor for the hydrogenation of polyaromatic nitrogen compounds such as quinoline (Q), isoquinoline (iQ), indole (ln), 5,6- and 7,8-benzoquinoline (BQ) and acridine (A) under relatively mild reaction conditions (125 °C, 4 atm H₂). The order of individual initial rates was: A > Q > 5,6-BQ > 7,8-BQ > ln > iQ, reflecting both steric and electronic effects. For the regioselective homogeneous hydrogenation of A to 9,10-dihydroacridine (DHA) catalysed by complex (1), a kinetic study was carried out; the experimentally determined rate law was r = k ₁ [Ru] [H₂]. These findings are consistent with a mechanism involving the hydrogenation of [RuH(CO)(A)(NCMe)(PPh₃)₂]BF₄ to yield DHA and the unsaturated species [RuH(CO)(NCMe)(PPh₃)₂]BF₄ in the rate-determining step.     

Effect of pH on the interfacial adsorption activity of pulmonary surfactant

The effect of pH on the interfacial adsorption activity of pulmonary surfactant was examined. Measurements of the surface tension were made in a Wilhelmy-like surface microbalance specially designed to assay small volumes of hypophase in thermostatically controlled conditions. Alkaline pH caused a significant decrease of the surface activity of both pulmonary surfactant and a lipid extract from surfactant (LES) (containing all of the lipids and surfactant protein-B (SP-B) and surfactant protein-C (SP-C) hydrophobic surfactant proteins, but lacking surfactant protein-A). The pK calculated from the change of surface activity versus pH was 9.18±0.26 and 9.27±0.31 for pulmonary surfactant and LES, respectively. The results from this study support the idea that electrostatic interactions between basic residues of SP-B and SP-C and negatively charged surfactant phospholipids could be important for the interfacial adsorption activity of pulmonary surfactant.     

A sensitive, rapid and specific determination of midazolam in human plasma and saliva by liquid chromatography/electrospray mass spectrometry

A rapid, sensitive and selective liquid chromatography/electrospray mass spectrometry (LC/ES-MS) method was developed for the quantitative determination of the anaesthetic benzodiazepine midazolam (MID) in human saliva and plasma from patients undergoing anesthesia procedures. Biological samples spiked with diazepam-d5, the internal standard, were extracted into diethyl ether. Compounds were separated on a Xterra RP18 column using a mobile phase of acetonitrile/formic acid 0.1% at a flow rate of 0.25 mL/min under a linear gradient. Column effluents were analyzed using MS with an ES source in the positive ionization mode. Calibration curves were linear in the concentration ranges of 1-250 and 0.2-25 ng/mL in plasma and saliva, respectively. The limits of detection were 0.5 ng/mL in plasma and 0.1 ng/mL in saliva, using a 0.5-mL sample volume. The recoveries of the spiked samples were above 65%. The method was applied to ten real samples from patients undergoing midazolam treatment.     

Demonstrating Linear Regression and Error Using an Experiment with a Microwave Oven

To provide an application for the method of linear least squares to data collected in a laboratory, a beaker with water is heated in a microwave oven, and the water temperature is measured as a function of heating variables (time and oven setting). This procedure enables a student to obtain a regression line for each oven setting, and to evaluate the intercept and slope of this line and compare them with the initial temperature of the water and the heating versus oven setting relationship described in the microwaves manufacturers manual. They also are asked to identify any sources of errors observed in this experiment.