神光Ⅱ上柱形黑腔辐射驱动冲击波

利用神光Ⅱ的八路三倍频激光装置，驱动柱形黑腔产生的x 射线作辐射源驱动台阶铝样品产生冲击波，获得了清晰的冲击波图像，通过冲击波过台阶样 品的时间差获得冲击波速度和压力分别为31.2km/s和17.5×10⁵MPa.采用软x射线能谱 仪通过激光注入孔测量的辐射温度与采用冲击波法测量辐射温度的结果一致. 关键词： 冲击波 辐射驱动 辐射温度     

Approximate confidence limits of the reliability performances for a cold standby series system

This paper is to investigate the approximate confidence limits of the reliability performances (such as failure rate, reliability function and average life) for a cold standby series system. The Bayesian approximate upper confidence limit of failure rate is obtained firstly, and next Bayesian approximate lower confidence limits for reliability function and average life are presented. The expressions for calculating Bayesian lower confidence limits of the reliability function and average life are also obtained, and an illustrative example is examined numerically by means of the Monte-Carlo simulation. Finally, the accuracy of confidence limits is discussed.     

Hydrogen indium vacancy complex VInH4 in n-type InP studied by positron-lifetime

Positron-lifetime experiments have been carried out on two undoped n-type liquid encapsulated Czochralski (LEC)-grown InP samples with different stoichiometric compositions in the temperature range 10-300 K. For temperatures below 120 K for P-rich InP and 100 K for In-rich InP, the positron average lifetime began to increase rapidly and then leveled off, which was associated with the charge state change of hydrogen indium vacancy complexes from (V_InH₄)⁺ to (V_InH₄)⁰. This phenomenon was more obvious in P-rich samples that have a higher concentration of V_InH₄. The transformation temperature of approximately 120 K suggests that the complex V_InH₄ is a donor defect and that the ionization energy is about 0.01 eV. The ionization of neutral V_InH₄ accounted for the decrease of the positron average lifetime when the sample was illuminated with a photon energy of 1.32 eV at 70 K. These results provide evidence for hydrogen complex defects in undoped LEC InP.     

Evaluation of closed-vessel microwave digestion method for the determination of trace impurities in polymer-based photoresist by inductively coupled plasma mass spectrometry

A closed microwave digestion method followed by inductively coupled plasma spectrometric (ICP-MS) analysis was evaluated for the determination of trace impurities in photoresist. To optimize the digestion procedure, several digestion parameters such as acid, heating temperature and heating time were evaluated. Besides, the digestion efficiency of used photoresist material and the recovery of analyte elements obtained by the use of gravimetric method and ICP-MS measurement, individually, were also compared to clarify the completeness of digestion. According to our experiments, the gravimetric method was found to be not so relevant to the completeness of digestion, because the remaining sample matrix could cause suppression effect in the subsequent ICP-MS measurement. In view of minimizing blank value and working time, a simple single-step heating program was proposed to mineralize 0.25 ml of photoresist material with 5 ml of nitric acid at 180 °C for 10 min. Based on the comparative study of the analytical results obtained by instrumental neutron activation analysis (INAA) and proposed method, the reliability of proposed method for the determination of trace metallic impurities in photoresist material has been confirmed.     

Investigation of the Li1+xV3O8 electrode–organic electrolyte interface by scanning photoelectron microscopy

To investigate the formation of a solid electrolyte interface (SEI) on the Li_1+xV₃O₈ electrode surface in the thermodynamic stability range of the organic electrolyte, we applied scanning photoelectron microscopy (SPEM) to a pristine electrode and to an electrode after ten cycles. The F K-edge absorption spectrum of the cycled electrode showed that LiF forms on the electrode surface during the lithium insertion–extraction process in the Li_1+xV₃O₈/Li cell. The photoelectron spectrum for the cycled electrode showed intense spectral features corresponding to Li 1s, F 2s, F 2p, and P 2p electron signals, whereas these spectral features were of negligible intensity for the pristine electrode. The above results give strong support for the formation of an SEI that consists of LiF and compounds containing phosphorus during operation of the battery. The SPEM images also revealed that the fluorine distribution on the surface of the cycled electrode was inhomogeneous.     

Applying a Mode Selector to Improve the Pulse-Compression Performance of Asymmetric-Coupled-Waveguide-Based Dispersion Compensators

An InGaAsP slab-type asymmetric-coupled-waveguide-based dispersion compensator with a mode selector has been designed and fabricated. The mode selector is necessary to select either a symmetric [with a positive group-velocity dispersion (GVD)] or antisymmetric (with a negative GVD) supermode. These supermodes exist simultaneously in the dispersion-compensation region of the device. Pulse-compression experiments were used to test the dispersion compensator, evaluating the function of the mode selector. A theoretical study of the experimental results shows that the mode selector obtains a very strong selectivity (nearly 100%) for the antisymmetric supermode.     

Comparative investigation of up-conversion luminescence in Tm/Yb-codoped germanate-niobic and germanium-bismuth glasses: effect of phonon density on up-conversion emission

Tm³⁺/Yb³⁺-codoped germanate-niobic (GN) and germanium-bismuth (GB) glasses have been synthesized by conventional melting and quenching method. Intense blue and weak red emissions centered at 477 and 650 nm, corresponding to the transitions ¹G₄→³H₆ and ¹G₄→³H₄, respectively, were observed at room temperature. The possible up-conversion mechanisms are discussed and estimated. GN glass showed a weaker up-conversion emission than GB glass, which is inconsistent with the prediction from the difference of maximum phonon energy between GN and GB glasses. In this paper, Raman spectroscopy was employed to investigate the origin of the difference in up-conversion luminescence in the two glasses. Compared with phonon side-band spectroscopy, Raman spectroscopy extracts more information including both phonon energy and phonon density. For the first time, our results reveal that, besides the maximum phonon energy, the phonon density of host glasses is also an important factor in determining the up-conversion efficiency.     

Synthesis and adsorption properties of gold nanoparticles within pores of surface‐functional porous polymer microspheres

Mesoporous polymer microspheres with gold (Au) nanoparticles inside their pores were prepared considering their surface functionality and porosity. The Au/polymer composite microspheres prepared were characterized by transmission electron microscope (TEM), X‐ray diffraction (XRD), and Brunauer–Emmett–Teller (BET) techniques. The results showed that the adsorption of Au nanoparticles could be increased by imparting the pore structure and surface‐functional groups into the supporting polymer microspheres (in this study, poly (ethylene glycol dimethacrylate‐co‐acrylonitrile) and poly (EGDMA‐co‐AN) system). Above all, from this study, it was established that the porosity of the polymer microspheres is the most important factor that determines the distribution and adsorption amount of face‐centered cubic (fcc) Au nanoparticles in the final products. Our study showed that the continuous adsorption of Au nanoparticles with the aid of the large surface area and surface interaction sites formed more favorably the Au/polymer composite microspheres. The BET measurements of Au/poly(EGDMA‐co‐AN) composite microspheres reveals that the adsorption of Au nanoparticles into the pores kept the pore structure intact and made it more porous. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5627–5635, 2004     

Electrochemical behavior of Li intercalation processes into a Li[NixLi(1/3−2x/3)Mn(2/3−x/3)]O2 cathode

Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂ (X=0.17, 0.25, 0.33, 0.5) compounds are prepared by a simple combustion method. The Rietvelt analysis shows that these compounds could be classified as having the α-NaFeO₂ structure. The initial charge-discharge and irreversible capacity increases with the decrease of x in Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂. Indeed, Li[Ni_0.50Mn_0.50]O₂ compound shows relatively low initial discharge capacity of 200 mAh/g and large capacity loss during cycling, with Li[Ni_0.17Li_0.22Mn_0.61]O₂ and Li[Ni_0.25Li_0.17Mn₀.₅₈]O₂ compounds exhibit high initial discharge capacity over 245 mAh/g and stable cycle performance in the voltage range of 4.8 -2.0 V. On the other hand, XANES analysis shows that the oxidation state of Ni ion reversibly changes between Ni²⁺ and about Ni³⁺, while the oxidation state of Mn ion sustains Mn⁴⁺ during charge-discharge process. This result does not agree with the previously reported ‘electrochemistry model’ of Li[Ni_xLi_(1/3−2x/3)Mn_(2/3−x/3)]O₂, in which Ni ion changes between Ni²⁺ and NI⁴⁺. Based on these results, we modified oxidation-state change of Mn and Ni ion during charge-discharge process.