静止轨道星载差分吸收光谱仪CCD成像系统设计

静止轨道卫星差分吸收光谱仪采用摆扫成像方式对大气进行探测,针对其工作时CCD成像系统信噪比大于1 000、高速探测模式下探测周期小于10min、高分辨率模式下探测周期小于1h的要求,进行CCD成像系统设计.选取CCD47-20作为探测器,设计成像电路实现光谱图像信号的采集和上传.分析了帧叠加和像元合并对时间、空间分辨率的影响.结合帧转移CCD的特点设计了每个位置最后一帧读出时摆镜转动的成像方式,并合理设置了帧叠加数和像元合并数,达到优化成像周期的目的.1s曝光时间条件下,该CCD成像系统的高速、高分辨率模式探测周期分别为515s和3 315s,图像信噪比均大于1 000,污染物观测实验中未出现失帧或重复的现象.该CCD成像系统方案满足静止轨道星载差分吸收光谱仪的探测需求,为静止轨道环境监测仪器设计提供参考.     

Fatigue life enhancement by irradiation of 12Cr1MoV steel with a Zr<Superscript>+</Superscript> ion beam. Mesoscale deformation and fracture

The structure and properties of 12Cr1MoV steel irradiated with a zirconium ion beam were studied by optical microscopy, scanning electron microscopy, and micro- and nanoindentation. It is shown that the modification covers the entire cross-section of the irradiated specimens to a depth of 1 mm. The data on irradiation-induced structural changes are used to interpret the changes in mechanical properties of the irradiated specimens under static and cyclic loading. Particular attention is given to analysis of strain estimation by the digital image correlation method.     

Microtextures Induced by Nanosecond Laser on Ni–Co Alloy Coatings

Ni–Co alloys have a wide range of applications in various fields owning to their excellent physical, chemical, and mechanical properties. In this paper, we prepare Ni–Co alloy coatings on 316L stain steel surfaces by electroplating. We present a novel approach utilizing a nanosecond laser to induce microtextures on Ni–Co alloy coatings. We study experimentally the effects of laser power and scanning rate on the surface morphologies of Ni–Co alloy coatings. The results indicate that the shape and size of induced microtextures can be controlled by the laser power and scanning rate. The size of grains increases with increase in the work current of the laser (WCL) at a certain scanning rate. With the WCL constant, the size of grains decreases with increase in scanning rate while their average height increases. It is a simple and easily-controlled method for the fabrication of microstructures on Ni–Co alloy coatings, which has promising applications in investigations of the properties of microtextured surfaces, such as friction, adhesion, and wetting.     

DFT mechanistic study of the H2‐assisted chain transfer copolymerization of propylene and p‐methylstyrene catalyzed by zirconocene complex

DFT computations have been performed to investigate the mechanism of H₂‐assisted chain transfer strategy to functionalize polypropylene via Zr‐catalyzed copolymerization of propylene and p‐methylstyrene (pMS). The study unveils the following: (i) propylene prefers 1,2‐insertion over 2,1‐insertion both kinetically and thermodynamically, explaining the observed 1,2‐insertion regioselectivity for propylene insertion. (ii) The 2,1‐inserion of pMS is kinetically less favorable but thermodynamically more favorable than 1,2‐insertion. The observation of 2,1‐insertion pMS at the end of polymer chain is due to thermodynamic control and that the barrier difference between the two insertion modes become smaller as the chain length becomes longer. (iii) The pMS insertion results in much higher barriers for subsequent either propylene or pMS insertion, which causes deactivation of the catalytic system. (iv) Small H₂ can react with the deactivated [Zr]?pMS?PP_n facilely, which displace functionalized pMS?PP_n chain and regenerate [Zr]? H active catalyst to continue copolymerization. The effects of counterions are also discussed. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 576–585     

80.5 MeV/u碳离子诱发铜靶的放射性剩余产物测量

高能重带电粒子能直接穿透靶原子核外电子层,与原子核发生直接碰撞,发生散裂反应,产生一系列具有放射性的剩余产物核.重带电粒子诱发靶材放射性剩余核与辐射防护和人员安全有着密切联系,当前,大部分剩余核产额主要依靠蒙特卡罗粒子输运程序进行模拟计算,其准确程度亟需通过实验测量进行准确评估.本文利用能量为80.5 MeV/u的(12)^C⁶⁺粒子对薄铜靶开展了辐照实验与伽玛射线测量,结合伽玛谱学分析方法,得出了辐照产生的18种放射性剩余产物的初始活度和产生截面值,并与PHITS模拟结果进行对比.结果表明,PHITS模拟程序对放射性剩余核种类的估计具有较高可靠性,在其绝对产额方面,与实验测量仍具有较大偏差.     

Gradient structure of polypropylene composites filled with carbon black

Russian Chemical Bulletin - Gradient polymer composites were prepared by melt-mixing of carbon black and polypropylene in a compounder and subsequent hot pressing of pellets. The thermally treated...