Pseudo-epitaxial C60 films prepared by a hot-wall method

We have used both reflection-geometry and grazing-incidence-geometry X-ray scattering to study thin films of C₆₀ evaporated onto mica substrates via a hot-wall technique. The growth mode yields close-packed C₆₀ planes, which are parallel to the substrate surface and which exhibit out-of-plane correlation lengths of 850 Å. In the film plane the C₆₀ is at best pseudo-epitaxial, with a 0.9° distribution of crystallite orientations, a 450 Å in-plane correlation length, and a 3.7% lattice mismatch, better than obtained by other thin film techniques but far from the accepted definition of single crystal thin film epitaxy.     

The “corset effect” of spin-lattice relaxation in polymer melts confined in nanoporous media

Linear polyethylene oxides with molecular weightsM _w of 1665 and 10170 confined in pores with variable diameters in a solid methacrylate matrix were studied by proton field-cycling nuclear magnetic resonance relaxometry. The pore diameter was varied in the range of 9–57 nm. In all cases, the spin-lattice relaxation time shows a frequency dependence close toT ₁∞ v^3/4 in the range ofv=3·10^?1-2·10¹ MHz as predicted by the tube-reptation model. This protonT ₁ dispersion essentially reproduces that found in a previous deuteron study (R. Kimmich, R.-O. Seitter, U. Beginn, M. Möller, N. Fatkullin: Chem. Phys. Lett. 307, 147, 1999). As a feature particularly characteristic for reptation, this finding suggests that reptation is the dominating chain dynamics mechanism under pore confinement in the corresponding time range. The absolute values of the spin-lattice relaxation times indicate that the diameter of the effective tubes in which reptation occurs is much smaller than the pore diameters on the time scale of spin-lattice relaxation experimens. An estimation leads to a valued ^*～0.5 nm. The impenetrability of the solid pore walls, the uncrossability of polymer chains (“excluded volume”) and the low value of the compressibility in polymer melts create the “corset effect” which reduces the lateral motions of polymer chains to a microscopic scale of only a few tenths of a nanometer.     

Direct SCF structure optimization of large molecules on networks of workstations

A program to optimize the structure of large molecules at the Hartree–Fock level of theory running concurrently on a network of workstations is presented. Problems encountered in obtaining nearly optimal speedup and their solutions are discussed. A simple scheduling algorithm is presented that enables up to 99.5% of the code to run in parallel. © 1993 John Wiley & Sons, Inc.     

Surface polarity of cellulose derivates observed by coumarin 151 and 153 as solvatochromic and fluorochromic probes

Solvent‐dependent ultraviolet–visible (UV–vis) absorption and Stokes shifts including strong hydrogen‐bond‐donating (HBD) solvents such as 2,2,2‐trifluoroethanol and 1,1,1,3,3,3‐hexafluoro‐2‐propanol of two coumarine dyes (Co 151 and Co 153) were analyzed with multiple‐square analyses of linear solvation energy relationships and the Kamlet–Taft solvent parameter set to α (HBD capacity), β (hydrogen‐bond‐accepting capacity), and π* (dipolarity/polarizability). The UV–vis absorption and emission spectra of Co 151 and Co 153 were measured when adsorbed on various polysaccharides such as different cellulose batches, carboxymethylcelluloses with different degrees of substitution, and chitine. As a result of this evaluation, Co 153 is recommended as an alternative UV–vis probe for evaluating the dipolarity/polarizability of cellulose and cellulose derivates. Multiple adsorption of Co 153 on Linters cellulose took place indicating a wide‐surface polarity distribution, which makes the determination of a rigid polarity parameter questionable. Thus, fluorescence measurements of adsorbed Co 153 are suitable to detect inhomogenities on a surface but not for the determination of empirical polarity parameters. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1210–1218, 2003     

Solution of monotone complementarity problems with locally Lipschitzian functions

The paper deals with complementarity problems CP(F), where the underlying functionF is assumed to be locally Lipschitzian. Based on a special equivalent reformulation of CP(F) as a system of equationsφ(x)=0 or as the problem of minimizing the merit functionΘ=1/2∥Φ∥ ₂ ² , we extend results which hold for sufficiently smooth functionsF to the nonsmooth case. In particular, ifF is monotone in a neighbourhood ofx, it is proved that 0 εδθ(x) is necessary and sufficient forx to be a solution of CP(F). Moreover, for monotone functionsF, a simple derivative-free algorithm that reducesΘ is shown to possess global convergence properties. Finally, the local behaviour of a generalized Newton method is analyzed. To this end, the result by Mifflin that the composition of semismooth functions is again semismooth is extended top-order semismooth functions. Under a suitable regularity condition and ifF isp-order semismooth the generalized Newton method is shown to be locally well defined and superlinearly convergent with the order of 1+p.     

Branched chain discotics Phase structure and orientation behaviour

Studies show that branching the side chains of hexakis(acoyloxy)-benzenes (HAB) and -cyclohexanes (HAChx) does not modify the structure of the discotic mesophase formed. Shear fields appear to act on entire columns, not on individual discs, thereby causing alignment of columns in the shear direction. X-ray diffraction patterns of samples at temperatures between 30°C and 40°C above the clearing temperature provide evidence for the presence of mesophase order.     

Problems, Models and Complexity. Part II: Application to the DLSP

In Part I of this study, we suggest to identify an operations research (OR) problem with the equivalence class of models describing the problem and enhance the standard computer-science theory of computational complexity to be applicable to this situation of an often model-based OR context. The Discrete Lot-sizing and Scheduling Problem (DLSP) is analysed here in detail to demonstrate the difficulties which can arise if these aspects are neglected and to illustrate the new theoretical concept. In addition, a new minimal model is introduced for the DLSP which makes this problem eventually amenable to a rigorous analysis of its computational complexity.     

A model for the interaction of near-infrared laser pulses with metal powders in selective laser sintering

A thermal model of the interaction of pulsed near-infrared laser radiation from a Nd:YAG laser was made, taking the measured powder properties such as reflectance, optical penetration depth and thermal conductivity into account. It allows an estimation of the evolution of two different temperatures: the average temperature of the powder (taken over the grains in a volume given by the laser beam diameter and the optical penetration depth) and the temperature distinction within a single grain. It showed that in pulsed mode consolidation can be achieved at much lower average power as the surface of the powder particles are molten but their cores remain at nearly room temperature. This leads to a much lower average temperature and therefore a dramatic decrease in residual thermal stresses in the finished piece. The results of the model were experimentally tested and confirmed. Received: 26 July 2001 / Accepted: 23 November 2001 / Published online: 23 January 2002