池沸腾传热的数学分析

在统计方法的基础上,对于池沸腾换热的传热机理提出了一个数学模型. 在没有增加新的经验常数的条件下,从该模型中可得到池沸腾热流密度是壁面过热度、活化穴最小与最大尺寸、流体的接触角与流体物理特性的函数. 该模型可以较好地解释润湿性如何影响沸腾热流密度. 对不同的接触角,模型预测的结果与实验相符合. 关键词： 池沸腾 传热 数学模型     

浸渍过程对纳米纤维素/二氧化硅复合气凝胶结构与性能研究

纳米纤维素(CNF)气凝胶兼具传统气凝胶的优异特性和自身优良的生物相容性和可降解性,在很多领域应用前景广阔。然而纤维素自身的超亲水性严重限制了其更广泛的应用,为改善纤维素气凝胶的亲水性能,提高其综合应用性能,采用简单浸渍法在纤维素气凝胶基体中引入二氧化硅(SiO₂)颗粒制备纳米纤维素/二氧化硅复合气凝胶,利用傅里叶红外光谱仪(FTIR)分析纤维素气凝胶和复合气凝胶的化学结构;用扫描电镜(SEM)观察气凝胶的微观结构;测定气凝胶的物理、力学性能和接触角。结果表明,复合气凝胶在3 340 cm-1处-OH吸收峰较纤维素气凝胶均有所减弱,表明SiO₂的引入促使Si-OH形成,也降低了气凝胶的亲水性,同时有Si-CH₃和Si-O-Si吸收振动峰出现,表明三甲基氯硅烷(TMCS)的改性作用以及纤维素与SiO₂颗粒之间形成稳定化学键连接。浸渍时间影响硅含量,进而影响气凝胶的密度、比表面积和孔隙率。当浸渍时间为10 min时制备的复合气凝胶性能较好,其微观结构分布均匀,具有疏水性能,接触角可达152°,同时气凝胶仍具有较好的力学性能和较低密度,其压缩模量和压缩性能分别为5.91和1.38 MPa,密度为0.1 g·cm-3。     

快重离子辐照对MoS2热导率的影响研究

利用0.97 GeV的209Bi离子辐照二硫化钼（MoS₂）晶体,辐照注量范围为1×1010～1×1012 ions/cm2,结合原子力显微镜（AFM）观测和Raman光谱分析研究了快重离子辐照对MoS₂热导率的影响。实验结果显示,快重离子辐照在MoS₂中产生了潜径迹,较高激光功率下的Raman测试使样品局部温度升高,导致E_1/2g和A_1g峰随注量增加向低波数方向移动,且峰形展宽。引入了通过改变激光功率测量Raman光谱得到MoS₂热导率的计算方法,获得了不同辐照注量下MoS₂的热导率的定量分析结果,随注量增加,热导率不断降低,从未辐照样品的563 W/mK下降到1×1012 ions/cm2辐照时的132 W/mK。Molybdenum disulphide (MoS₂) was irradiated by 0.97 GeV 209Bi ions with the fluence of 1×1010 to 1×1012 ions/cm2. The irradiation effect on the thermal conductivity of MoS₂ was analyzed by atomic force microscope (AFM) and Raman spectroscopy. The experimental results show that hillock-like latent tracks are observed on irradiated MoS₂ by AFM. The measurement of MoS₂ by Raman spectrometer with high laser power results in the increase of local temperature of MoS₂, which cause the downshift of peaks position and broadening of E_1/2g and A_1g peak. Furthermore, according to Raman spectra measured at different laser power, thermal conductivity of MoS₂ before and after irradiation was calculated, which show that the thermal conductivity of MoS₂ decreases with increasing fluence, from 563 to 132 W/mK for pristine and 1×1012 ions/cm2 irradiated MoS₂, respectively.     

EAST中性束反向注入的初步实验研究

对EAST中性束反向注入过程中等离子体加热和电流驱动进行了实验研究,并采用了美国普林斯顿大学等离子体物理实验室开发的TRANSP 程序对高功率中性束注入过程中能量热输运进行了分析。结果表明,中性束注入可有效提高本底等离子体温度,产生束驱动非感应电流,提高等离子体旋转以及有效改善等离子体约束。     

BEPCⅡ束流损失探测系统及其初步应用

束流寿命是衡量储存环性能的重要参数, 它直接影响到储存环能否正常运行. 采用束流损失探测系统通过探测束流损失的地点, 可以为分析束损原因、优化机器参数和提高束流寿命提供依据. 介绍了北京正负电子对撞机重大改造工程(BEPCⅡ)束流损失探测系统的基本情况: 前端束流损失探测器输出的脉冲信号送到下位机进行处理, 通过CAN总线将所有的下位机连接到位于本地站的前端PC机, 此PC机再通过以太网与中控室的PC机或工作站进行数据通讯, 最终实现对束流损失的实时监测、数据存储, 并能对历史数据进行处理, 达到实时显示全环束损分布的目的. 文章最后还简要介绍了整个系统在BEPCⅡ调束过程中的初步应用.     

CSRm变谐波加速

 在研究兰州重离子冷却储存环(HIRFL-CSR)纵向相振荡运动特性的基础上,对主环(CSRm)内重离子的加速过程进行了模拟研究。选取由扇聚焦回旋加速器（SFC）剥离注入的能量为7 MeV/u,动量散度为±0.5%的¹²C⁶⁺典型离子,模拟了CSRm内束流的加速过程,加速的最终能量为1 GeV/u。在加速过程中采用了变换谐波的方式,解决了较低能量下的加速问题。模拟结果给出了不同时刻粒子在纵向相空间的分布以及各主要高频参数随时间的变化曲线。     

基于量子点和MEH-PPV的白光发光二极管的研究

利用无机纳米材料与有机聚合物材料相结合的方法制备白光发光二极管器件, 研究了蓝光量子点QDs(B)掺杂聚[2-甲氧基-5-(2-乙基己氧基-1, 4-苯撑乙烯撑](MEH-PPV) 复合体系的发光特性及量子点QDs(B) 掺杂浓度(质量分数)不同对器件发光特性的影响. 制备了ITO/PEDOT:PSS/MEH-PPV:QDs(B)/LiF/Al 结构的电致发光器件, 测试了器件的电致发光光谱和电学、光学特性. 当QDs掺杂浓度为40%, 驱动电压为8 V时器件能得到较为理想的白光发射. 同时, 对比研究了非掺杂体系的发光特性, 制备了结构为ITO/PEDOT:PSS/MEH-PPV/QDs(B)/LiF/Al的器件, 掺杂体系相较于非掺杂体系, 器件的最大亮度增大, 启亮电压降低, 并分析了掺杂体系器件性能改善的原因.     

高灵敏度Sb基量子阱2DEG的霍尔器件（英文）

用分子束外延技术将高灵敏度的In As/Al Sb量子阱结构的Hall器件赝配生长在Ga As衬底上。设计了由双δ掺杂构成的Hall器件的新结构,有效地提高了器件的面电子浓度。与传统的没有掺杂的In As/Al Sb量子阱结构的Hall器件相比,室温下器件电子迁移率从15 000 cm~2·V~(-1)·s~(-1)提高到16 000 cm~2·V~(-1)·s~(-1)。AFM测试表明材料有好的表面形态和结晶质量。从77 K到300 K对Hall器件进行霍尔测试,结果显示器件不同温度范围有不同散射机构。双δ掺杂结构形成高灵敏度、高二维电子气(2DEG)浓度的In As/Al Sb异质结Hall器件具有广阔的应用前景。     

Neutron activation analysis of sources of raw material of Emperor Qin Shi Huang’s Terracotta warriors and horses

There have been selected 83 samples of terracotta warriors and horses of Emperor Qin Shi Huang's Mausoleum, 20 samples of clays taken from around Qin's Mausoleum and 2 samples of Yaozhou porcelain bodies. All these samples have been measured by instrument neutron activation analysis (INAA) and as many as 32 kinds of element contents of each sample are measured. The following conclusion has been reached when fuzzy cluster analysis is conducted to element contents of all these samples: (i) The samples are roughly classified into five categories: namely, samples from pits No. 1 and No. 2; samples from pit No. 3; loam layers; the mixture of loam and loess; and Yaozhou porcelain bodies. (ii) The terracottawarriors and horses in pits No. 1, No. 2 and No. 3 are relatively independent from one another. The clays from which they were made are not entirely identical.We have found that samples in pit No. 3 are very closely related and their claysources are comparatively concentrated. Samples in pits No. 1 and No. 2 are less related and their clay sources are comparatively scattered. (iii) The clays from which the terracotta warriors and horses were made are closely related to theloam layer near Qin's Mausoleum, particularly to the loam layer of Zaoyuan village and Gaoxing village, but they are not so related to loess layers there, nor to the loam layers of Anhoubao, even less related to Yaozhou porcelain bodies. Arational deduction thus drawn is that the raw material of clays from which the terracotta warriors and horses were made might probably be taken from loam layers around Zaoyuan and Gaoxing, or loam layers near Qin's Mausoleum whose properties are identical with those of loam layers of Zaoyuan and Gaoxing, rather than loess layers around the above places. Since the raw material of the terracotta warriors and horses was taken from loam near Qin's Mausoleum, it could be deductedthat the kiln sites might be located in around Qin's Mausoleum.     

基于LR305的平面荧光太阳能聚光波导研制

光伏发电是目前太阳能最佳的利用方式之一,但发电成本高。利用聚光结构提高光的转换和收集效率,是提高太阳能电池效率、减少电池用量、降低光伏发电系统成本的重要途径。以Lumogen F Red 305 (LR305) 染料作为荧光材料,将其掺杂到PMMA中,通过本体聚合法制作出尺寸为50 mm×50 mm×5 mm的PMMA平面荧光太阳能聚光波导,对其光学特性进行表征,同时将太阳能电池粘贴到聚光波导的输出端面,通过测试平面荧光太阳聚光波导对太阳能电池性能的影响研究了荧光太阳能聚光波导的聚光特性。