兰州重离子加速器分时供束的Chopper模式解析

 介绍了兰州重离子加速器分时供束系统中Chopper模式解析子系统的体系结构及硬件组成,分析了软件需求,并采用多线程技术设计了Chopper模式解析程序。首先使用NI-DAQmx函数实时读取PXI6133数据采集卡上采集的Chopper模式脉冲,然后对其作进一步分析,最后使用TCP/IP协议将相应的工作模式控制指令发送给控制器。设计的程序达到了系统要求,实现了Chopper模式自动转换的功能,并通过了现场测试。     

多重故障模式下的电动伺服系统故障建模方法

针对电动伺服系统的多重故障建模问题,提出了基于仿真模型重构和故障模型嵌套组合的多重故障建模方法。将电动伺服系统划分为若干功能单元,在各功能单元仿真模型基础上,提炼故障描述函数,利用统一故障表达式构建各功能单元故障模型。为了有效描述系统多重故障,提出了功能单元内多故障模型逐层嵌套+功能单元间故障模型组合的故障建模方法,重点分析并给出了不同类型多重故障的故障模型嵌套原则。仿真分析和实验验证结果表明,所建立故障模型可有效描述多重故障发生时的系统工作性能,提出的多重故障建模方法合理有效,具有普遍适用性,为故障诊断、构建故障知识库和容错控制仿真验证等提供了良好的研究手段。     

放射性次级束流分离器真空系统的压力分布

放射性次级束流分离器是强流重离子加速器装置中,连接增强器和高精度环形谱仪的束流输运线,用于传输重离子束流以及放射性次级束流。为了满足束流传输的要求,并维持相连增强器和高精度环形谱仪的极高真空,放射性次级束流分离器真空系统的平均压强应低于5×10-7 Pa。因此,需要验证真空系统设计方案的可行性,以及设计方案能否满足要求的压强范围。通过现有的同步储存环CSRm中的真空计监测数据以及软件BOLIDE的模拟结果对比,对真空压力计算软件VAKTRAK的使用方法和计算结果进行验证;采用VAKTRAK模拟计算不同真空参数下（流导、出气率以及泵速）放射性次级束流分离器真空系统的压力分布。根据计算结果,放射性次级束流分离器真空系统的平均压强可以达到1.79×10-7 Pa （H₂）,满足物理实验和工程设计的要求。通过模拟计算结果,放射性次级束流分离器真空系统的设计方案的可行性得到验证,系统设计的真空度满足要求。HIAF Fragment Separator(HFRS) is connected with Booster Ring(BRing) and Spectrometer Ring (SRing) in the HIAF and used to transfer the ion beams and radioactive secondary beams. To satisfy the requirements of beam transmission and maintain the extremely high vacuum of BRing and SRing, the average pressure of HFRS vacuum system should be lower than 5×10-7 Pa. Therefore, the feasibility of the design scheme and whether the design scheme would fulfill the required vacuum range or not should be verified. Based on the measured data on the current sychrontron CSRm and the simulation results of BOLIDE, the calculation results of VAKTRAK are verified and then VAKTRAK is used to calculate the pressure profiles of different parameters(such as the conductance, out-gassing and pumping speed) for HFRS. According to the calculation results, the average pressure of HFRS vacuum system could be 1.79×10-7(H₂) which achieves the required pressure for physics experiments and engineering design. According the calculation results of this paper, the feasibility of the designed HFRS vacuum system has been verified and the design of system satisfies the vacuum requirements.     

CSR-LINAC IH-RFQ的高频电磁设计

中国科学院近代物理研究所在CSR-LINAC项目中设计了一台108.48 MHz的IH型RFQ直线加速器。该RFQ可以将质荷比为3~7的离子从4 keV/u加速到300 keV/u。在完成束流动力学设计的基础上,主要针对RFQ腔体的高频电磁设计展开了研究,同时利用了电磁场仿真和束流动力学模拟来研究腔体的四极场不平整度和二极场及其动力学影响。未经调谐的情况下,腔体的谐振频率为108.15 MHz,腔体空载品质因子Q₀为5 910,腔体功耗为123 kW。通过在支撑板两端增加底切的设计,将腔体的四极场不平整度由-21%~ 12%优化至±2.5%,满足了束流动力学要求。腔体的二极场为-3%~ -2.2%,使得束流在垂直方向小幅振荡,RFQ的垂直方向接受度减小5%。为了保证功率馈入时反射较小,将耦合器设置在临界耦合状态,耦合面积为940 mm2。为了补偿腔体的频率偏差和漂移,设计了调谐量分别为707和132 kHz的固定调谐器和可动调谐器。The 108.48 MHz IH type RFQ for CSR-LINAC project is under design at Institute of Modern Physics, Chinese Academy of Sciences. This RFQ can accelerate heavy ions with mass to charge ratio of 3~7 from 4 keV/u to 300 keV/u. According to the beam dynamics requirement, the RF structure design has been finished. The quadrupole field unflatness and dipole field of the cavity were studied by electromagnetic simulation and beam dynamics simulation. The frequency of the cavity without tuning is 108.15 MHz, the Q₀ of the cavity is 5910, and the RF power loss is 123 kW. The quadrupole field unflatness of ±2.5%,which was -21%~12% before optimizing, is achieved to meet dynamics requirement through the undercuts in cavity supporters. The dipole field of -3%~ -2.2% causes the oscillation of the beam center and acceptance reduction of 5%. The power coupler must be in critical coupling state with the coupling area of 940 mm2 for minimum reflection coefficient. The tuners, consist of coarse and fine tuners with frequency shift of 707 and 132 kHz respectively, is used for tuning of frequency deviation of the cavity.     

HITFiL同步加速器剥离注入

一台新的治癌专用加速器HITFiL正在设计和建造中,其中一台同步加速器为其主加速器,以高紧凑性、高可靠性和低成本为设计目标。同步加速器的注入系统采用剥离注入方式,剥离注入与单圈注入方式相比能达到较高的注入效率,而其造价明显低于多圈注入加电子冷却的注入方式。治癌采用碳粒子束,从ECR离子源产生的C5+离子经过回旋加速器预加速后在同步加速器注入点处剥离成为C6+注入到环里。详细阐述了该注入系统的设计方案,并对整个注入过程进行了计算机模拟。在模拟过程中,对束流的注入效率、束流损失机制和粒子数增益进行了研究,得到了实空间和相空间的粒子分布和发射度增长趋势,得到了满足要求的束流流强。     

Simulation and analysis of the transverse spectrum in HIRFL-CSR

Particles in a storage ring oscillate in the longitudinal and transverse dimensions. Therefore, the signal that beam has generated can be analyzed in the frequency domain to extract many beam parameters, such as tune, momentum spread, emittance and their evolution with time and so on. In this paper, the transverse spectrum in HIRFL-CSR was simulated and analyzed under different conditions, including electron cooling, hollow electron beam, solenoid effect, the tune shift caused by power supply ripple and the misalignment between ion and electron beams. The result of the simulation shows that the longitudinal magnetic field of the electron cooling device should be compensated by a “compensation solenoid”, and the power supply ripple must be controlled, otherwise the accumulation would be affected and the beam would be lost.     

苯并三噻吩共轭聚合物的合成及其在有机光伏中的应用

以三(二亚苄基丙酮)二钯(Pd_2(dba)_3)为催化剂,三甲苯基磷(P(o-tol)_3)为配体,4,3'-十二烷基-2,2'-联二噻吩(M1)和2,8-二溴-5-(2-己基癸基)苯并三噻吩(M2)为单体,采用Stille交叉偶联反应,合成了基于苯并三噻吩和联二噻吩单元的共轭聚合物(PBTT)。采用热重分析、紫外-可见分光光度计及电化学分析分别研究了聚合物PBTT的热性能、光学性能和电化学性能。结果表明:聚合物PBTT具有优异的热稳定性和低的最高占有轨道能级(HOMO);聚合物薄膜最大吸收峰位于469 nm,光学能带隙为2.10 eV;将聚合物与[6,6]-苯基-C_(61)-丁酸甲酯(PC_(61)1BM)共混材料作为活性层制作了本体异质结构太阳能电池器件,在模拟太阳光源AM 1.5 G 100 mW/cm~2照射条件下,该器件获得了高达1.00 V的开路电压,初步的能量转化效率为0.43%。     

Study of a magnetic alloy-loaded RF cavity for bunch compression at the CSR

The Heavy Ion Research Facility and Cooling Storage Ring（HIRFL-CSR）accelerator in Lanzhou offers a unique possibility for the generation of high density and short pulse heavy ion beams by non-adiabatic bunch compression longitudinally,which is implemented by a fast jump of the RF-voltage amplitude.For this purpose,an RF cavity with high electric field gradient loaded with Magnetic Alloy cores has been developed.The results show that the resonant frequency range of the single-gap RF cavity is from 1.13 MHz to 1.42 MHz,and a maximum RF voltage of 40 kV with a total length of 100 cm can be obtained,which can be used to compress heavy ion beams of 238U72＋ with 250 MeV/u from the initial bunch length of 200 ns to 50 ns with the coaction of the two single-gap RF cavity mentioned above.     

HIRFL-CSR commissioning in 2006 and 2007

HIRFL-CSR, a new heavy ion cooler-storage-ring system at IMP, had been in commissioning since the beginning of 2006. In the two years of 2006 and 2007 the CSR commissioning was finished, including the stripping injection (STI), electron-cooling with hollow electron beam, C-beam stacking with the combination of STI and e-cooling, the wide energy-range synchrotron ramping from 7 MeV/u to 1000 MeV/u by changing the RF harmonic-number at mid-energy, the multiple multi-turn injection (MMI), the beam accumulation with MMI and e-cooling for heavy-ion beams of Ar, Kr and Xe, the fast extraction from CSRm and single-turn injection to CSRe, beam stacking in CSRe and the RIBs mass-spectrometer test with the isochronous mode in CSRe by using the time-of-flight method.     

聚丙烯酸酯型高分子侧链液晶的合成及其对聚乙烯成核结晶行为的影响

基于聚烯烃用成核剂的结构特征设计合成了两种极性基团和非极性基团交替排列的乙烯基单体,并利用自由基引发聚合,制备出相应的侧链型液晶聚合物.采用元素分析、红外光谱和核磁共振氢谱对所合成单体和聚合物的结构进行了确认.并采用热失重(TGA)和差示扫描量热仪(DSC)研究了聚合物的热稳定性和相转变温度.结果表明,所合成聚合物的起始热分解温度均在337℃以上,具有优异的热稳定性;液晶相变温度区间可达186 K,具有较宽的液晶态温度范围.热台偏光显微镜(HS-POM)研究结果表明,聚合物均呈现出纹影织构,证明所合成的聚合物均为热致向列型侧链液晶高分子.采用DSC和HS-POM研究了所合成的侧链液晶聚合物对高密度聚乙烯(HDPE)异相成核结晶行为的影响.结果表明,侧链型液晶聚合物在提高HDPE结晶温度、结晶度以及降低HDPE晶粒的尺寸及分布方面均有优异的效果,是一类HDPE有效的成核剂.