Pressure and temperature dependence of the gas‐transport properties of dense poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] membranes

The gas‐transport properties of poly[2,6‐toluene‐2,2‐bis(3,4‐dicarboxylphenyl)hexafluoropropane diimide] (6FDA‐2,6‐DAT) have been investigated. The sorption behavior of dense 6FDA‐2,6‐DAT membranes is well described by the dual‐mode sorption model and has certain relationships with the critical temperatures of the penetrants. The solubility coefficient decreases with an increase in either the pressure or temperature. The temperature dependence of the diffusivity coefficient increases with an increase in the penetrant size, as the order of the activation energy for the diffusion jump is CH₄ > N₂ > O₂ > CO₂. Also, the average diffusion coefficient increases with increasing pressure for all the gases tested. As a combined contribution from sorption and diffusion, permeability decreases with increases in the pressure and the kinetic diameter of the penetrant molecules. Even up to 32.7 atm, no plasticization phenomenon can be observed on flat dense 6FDA‐2,6‐DAT membranes from their permeability–pressure curves. However, just as for other gases, the absolute value of the heat of sorption of CO₂ decreases with increasing pressure at a low‐pressure range, but the trend changes when the feed pressure is greater than 10 atm. This implies that CO₂‐induced plasticization may occur and reduce the positive enthalpy required to create a site into which a penetrant can be sorbed. Therefore, a better diagnosis of the inherent threshold pressure for the plasticization of a glassy polymer membrane may involve examining the absolute value of the heat of sorption as a function of pressure and identifying the turning point at which the gradient of the absolute value of the heat of sorption against pressure turns from a negative value to a positive one. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 354–364, 2004     

Colorimetric recognition of different enzymology-concerning transition metals based on a hybrid cluster complex.

A hybrid cluster complex, formed by chelating a chromogenic ligand to a [2Fe-2S] cluster, sensitively exhibited differential colorimetric responses towards Hg2+, Cd2+, Cr3+, Pb2, Sn2+, Cu2+, Zn2+, Fe3+ and Co2+ in water at physiological pH. Speciation of some of these metal elements, such as Cr(III) and Sn(IV), was also studied by UV/Vis absorption.     

Fluorescent-based single-strand conformation polymorphism/heteroduplex capillary electrophoretic mutation analysis of the P53 gene.

Fluorescent-based single-strand conformation polymorphism (F-SSCP) analysis with capillary electrophoresis (CE) is the most common method for the detection of mutation because of its high sensitivity and resolution. In this study, we prepared an inexpensive linear polyacrylamide (LPA), and successfully applied it to CE-SSCP analysis and tandem CE-SSCP/heteroduplex analysis (HA) of the P53 gene on an ABI capillary genetic analyzer. A comparison of the sieving capabilities of a homemade LPA and commercial polydimethylacrylamide (PDMA) demonstrates that the homemade LPA has a higher resolution, a shorter analysis time, and is more suitable for tandem SSCP/HA than commercial PDMA. To show the usefulness, mutations of P53 gene exon 7 - 8 in 37 tumor samples were investigated by using homemade LPA. The results indicate that 10 mutations were found in 9 of 37 cases; the majority of P53 mutations were missense mutations, and 70% were located in exon 7, which plays an important role in neoplastic progression in human tumorigenesis.     

Concentrations of hazardous heavy metals in environmental samples collected in Xiamen, China, as determined by vapor generation non-dispersive atomic fluorescence spectrometry.

Non-dispersive atomic fluorescence spectrometry (NDAFS) coupled with vapor generation (VG) sample introduction was applied to the determination of the concentrations of hazardous heavy metals, such as arsenic, cadmium, lead and mercury, in seawater, soils and total airborne particulate matter (PM) collected around the Xiamen area in China. Almost 100% sample introduction efficiency was achieved by using thiourea and ascorbic acid for the pre-reduction of As(V) to As(III), K3Fe(CN)6 and tartaric acid for pre-oxidation of Pb(II) to Pb(IV), and masking the interferences arising from the co-existing transition metals to As, Cd, Hg and Pb during their vapor generation process. Moreover, a novel sample pretreatment device was developed to avoid the loss of mercury, lead, cadmium and arsenic during sample pretreatment. With such methods, the detection limit (DL) of arsenic, cadmium, lead and mercury was down to 0.08, 0.03, 0.05, 0.01 ng mL(-1) (3sigma), respectively. The relative standard deviations (RSD, n = 11) for arsenic, cadmium, lead and mercury at 10 ng mL(-1) were 0.9%, 1.6%, 1.3% and 2.0%, respectively. The concentrations of hazardous heavy metals in the environmental samples collected in Xiamen, China are in the range from 0.02 +/- 0.001 ng mL(-1) in seawater to 15.3 +/- 0.2 microg g(-1) in soils. Besides flame/GF-AAS and ICP-AES/MS, VG-NDAFS should be another choice for the determination of hazardous heavy metals in environmental samples.     

Determination of tyrosine traces by adsorption voltammetry of its copper (II) complex

The electrochemical behavior of the copper-tyrosine complex has been studied by linear-sweep adsorption voltammetry. In 0.02 mol/L Na₂HPO₄ buffer solution (pH=9.6), the complex can be adsorped on a hanging mercury drop electrode and reduced at a peak potential of about –0.42 V (vs. SCE). The secondary derivative peak height is linear proportional to the concentration of tyrosine in the range 1.0×10^–7–5.0×10^–5 mol/L. The detection limit is 5×10^–8 mol/L.Project supported by the Provincial Science Foundation of Shandong Province     

Ba（n，x）~（134）Cs，~（134）Ba（n，2n）~（133）Ba，

用中子活化法相对于５４Ｆｅ（ｎ，Ｐ）５４Ｍｎ反应，在１３．５０—１４．８０ＭｅＶ中子能区测量了Ｂａ（ｎ，ｘ）１３４Ｃｓ，１３４Ｂａ（ｎ，２ｎ）１３３Ｂａ，１４０Ｃｅ（ｎ，２ｎ）１３９Ｃｅ，１４２Ｃｅ（ｎ，２ｎ）１４１Ｃｅ和２３Ｎａ（ｎ，２ｎ）２２Ｎａ的反应截面．并将所测的结果和其他作者的结果进行了比较，中子能量是用９０Ｚｒ（ｎ，２ｎ）８９ｍ＋ｇＺｒ反应和９３Ｎｂ（ｎ，２ｎ）９２ｍＮｂ反应截面比法测定的。     

Developing a hybrid emulsion polymerization system to synthesize Fe3O4/polystyrene latexes with narrow size distribution and high magnetite content

A hybrid emulsion polymerization was formulated for synthesizing Fe₃O₄/polystyrene composite latex. This system, containing binary droplets that are magnetic (Mag)‐droplets with a diameter of 100–200 nm and styrene (St)‐droplets with a diameter of 3–4 μm, was obtained by mixing Mag‐miniemulsion and St‐macroemulsion. With extremely low surfactants concentration (?critical micelle concentration, CMC), the nucleated loci are selectively controlled in the Mag‐droplets, as the result of smaller droplet size and larger surface ratio. Both water‐soluble potassium persulfate (KPS) and oil‐soluble 2,2′‐azobis(2‐isobutyronitrile) was adopted to initiate the polymerization. In the presence of KPS, magnetic polystyrene latices with particles size of 60–200 nm, narrow size distribution, and high magnetite content (86 wt % measured by TGA) were attained successfully. The synthesized magnetic Fe₃O_4/polystyrene latices assembled into well‐ordered hexagonal structure in the surface of a carbon supported copper grid. The influence of various parameters on various aspects of the as‐synthesized Fe₃O₄/polystyrene was investigated in detail: type of initiator on composite morphology, feed ratio of Mag‐miniemulsion and St‐macroemulsion on magnetite content, and hydrophobic agent or amount of surfactant on size and size distribution. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5285–5295, 2007     

函数模拟法求解锥形模超塑挤压的力学场——超塑挤压解析理论之一

本文首次用模拟位移函数的方法,给出锥形模超塑挤压力学场的解析式以及应变、应变速率和应力的约束方程。由于实验选用的是典型超塑性合金ZnAl₅,所以结果有相当的包络性。即使对于非典型超塑性材料,这种方法亦有普遍意义。     

The study of lithium fast ion conductors of Li3xLa0.67−xScyTi1−2yNbyO3 system

Perovskite-type lithium fast ion conductors of Li_3xLa_0.67−xSc_yTi_1−2yNb_yO₃ system were prepared by solid state reaction. X-Ray powder diffraction shows that perovskite solid solution form in the ranges of x=0.10, y≤0.10. AC impedance measurements indicate that the bulk conductivities and the total conductivities are of the order of 10⁻⁴ S·cm⁻¹ and 10⁻⁵ S·cm⁻¹ at 25 °C respectively. The compositions have low bulk activation energies of about 17 kJ/mol in the temperature ranges of 298 – 523 K and total activation energies of about 37 kJ/mol in the temperature ranges of 298 – 523 K.     

Effect of end groups on complexation kinetics between cyclodextrins and guest polymers

α‐Cyclodextrin (α‐CD) has been complexed with various poly(ethylene glycol) (PEG) derivatives in aqueous solution. It has been found that the end groups of PEG derivatives affect the complexation kinetics greatly, but have only a little influence on the thermodynamic behavior. By increasing the hydrophobicity of end groups, the complexation speeds up rapidly. On the other hand, the bulky end groups slow down the threading of polymeric guests into the cavity of CD. By changing the hydrophobicity and the size of end groups, the complexation rate can be adjusted in the range of several orders of magnitudes, which should be quite useful in the design of new supramolecular systems. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2050–2057, 2006