醇体系中合成CuGaS2纳米晶及其形貌演变

以CuCl2·2H2O,自制的GaCl3和(NH2)2CS为原料,在乙二醇体系中合成了花状结构的CuGaS2纳米晶．产物分别用X射线粉末衍射仪、透射电子显微镜、场发射扫描电子显微镜、高分辩透射电子显微镜和X射线光电子能谱仪进行了表征．实验结果表明,220℃反应24 h得到均匀的花状纳米结构CuGaS2,它是由厚度80-100 nm的片晶组成．同时,通过反应时间的控制,可以清楚的看到由纳米颗粒到纳米球以及花状纳米结构的演变过程．另外,研究了反应温度、反应时间、溶剂等对产物和形貌的影响．此外,对花状结构纳米晶的生长机理进行了初步的探讨．室温荧光光谱表明,随粒径的降低,发光位发生了部分蓝移．     

旋涡运动的稳定性与角动量守恒

本文利用角动量作为Liapunov函数建立二维的圆形涡块及涡环在有限或无限区域上的(Liapunov)非线性稳定性.     

强预不变凸函数的充要条件

本文讨论了强预不变凸函数与预不变凸函数、严格预不变凸函数及半严格预不变凸函数之间的关系,得到它的三个充要条件：(i)在一定条件下,f是强预不变凸函数的充分必要条件是f是预不变凸函数且f满足中间点强预不变凸性；(ii)在一定条件下,f是强预不变凸函数的充分必要条件是f是严格预不变凸函数且f满足中间点强预不变凸性；(iii)在一定条件下,f是强预不变凸函数的充分必要条件是f是半严格预不变凸函数且f满足中间点强预不变凸性．     

水合乙酸锌脱水反应的动力学

用等温热重法和非等温热重法研究了Zn(CH3COO) 2·2H2 O的脱水反应 .在 61.1、62 .8、66.2、69.9℃下的等温热重数据 ,由等转化率下的lnt=E/RT +ln[g(α) /A]进行拟合 ,确定了活化能的大小 ;升温速率为 10℃ /min的非等温热重曲线显示 ,Zn(CH3COO) 2·2H2 O的脱水反应发生在 71～ 10 2℃间 ,其数据通过Doyle Zsako法进行拟合 ,以线性相关系数为判据 ,并结合等温热分析拟合结果 ,得到该脱水反应的积分动力学模式函数g(α) =[-ln( 1-α) ]2 / 3、活化能E =10 0 .8kJ/mol、指前因子ln(A/s-1) =3 6.0 9、动力学补偿效应方程为lnA =0 .3 3 3 9E + 2 .0 10 .     

Ethylene–propylene copolymerization with bis(β‐enaminoketonato) titanium complexes activated with modified methylaluminoxane

Ethylene–propylene copolymerization, using [(Ph)NC(R₂)CHC(R₁)O]₂TiCl₂ (R₁ = CF₃, Ph, or t‐Bu; R₂ = CH₃ or CF₃) titanium complexes activated with modified methylaluminoxane as a cocatalyst, was investigated. High‐molecular‐weight ethylene–propylene copolymers with relatively narrow molecular weight distributions and a broad range of chemical compositions were obtained. Substituents R₁ and R₂ influenced the copolymerization behavior, including the copolymerization activity, methylene sequence distribution, molecular weight, and polydispersity. With small steric hindrance at R₁ and R₂, one complex (R₁ = CF₃; R₂ = CH₃) displayed high catalytic activity and produced copolymers with high propylene incorporation but low molecular weight. The microstructures of the copolymers were analyzed with ¹³C NMR to determine the methylene sequence distribution and number‐average sequence lengths of uninterrupted methylene carbons. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5846–5854, 2006     

Template atom transfer radical polymerization of a diaminopyrimidine‐derivatized monomer in the presence of a uracil‐containing polymer

Uracil‐derivatized monomer 6‐undecyl‐1‐(4‐vinylbenzyl)uracil and diaminopyrimidine‐derivatized monomer 2,6‐dioctanoylamido‐4‐methacryloyloxypyrimidine (DMP) were synthesized and polymerized by atom transfer radical polymerization (ATRP). A well‐defined, highly soluble, uracil‐containing polymer, poly[6‐undecyl‐1‐(4‐vinylbenzyl)uracil] (PUVU), was prepared in dioxane at 90 °C with CuBr/1,1,4,7,10,10‐hexamethyltriethylenetetramine as the catalyst and methyl α‐bromophenylacetate as the initiator. PUVU was further used as a template for the ATRP of DMP. The enhanced apparent rate constant of the DMP polymerization in the presence of PUVU indicated that the ATRP of DMP occurred along the PUVU template. The template polymerization produced a stable and insoluble macromolecular complex, PUVU/poly(2,6‐dioctanoylamido‐4‐methacryloyloxypyrimidine). An X‐ray diffraction study confirmed that the complex had strandlike domains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6607–6615, 2006     

Effects of the architecture and environment on polymeric molecular assemblies of novel amphiphilic diblock copolynorbornenes with narrow polydispersity via living ring‐opening metathesis polymerization

Diblock copolymers of 5‐(methylphthalimide)bicyclo[2.2.1]hept‐2‐ene (NBMPI) and 1,5‐cyclooctadiene were synthesized by living ring‐opening metathesis polymerization with a well‐defined catalyst {RuCl₂(CHPh)[P(C₆H₁₁)₃]₂}. Unhydrogenated diblock copolymers showed two glass transitions due to poly(NBMPI) and polybutadiene segments, such as two glass‐transition temperatures at ?86.5 and 115.3 °C for poly 1a and ?87.2 and 115.3 °C for poly 1b . However, only one melting temperature could be observed for hydrogenated copolymers, such as 119.8 °C for poly 2a and 121.7 °C for poly 2b . The unhydrogenated diblock copolymer with the longer poly(NBMPI) chain (poly 1a ; temperature at 10% mass loss = 400 °C) exhibited better thermal stability than the one with the shorter poly(NBMPI) chain (poly 1b ; temperature at 10% mass loss = 385 °C). Two kinds of hydrogenated diblock copolymers, poly 2a and poly 2b , exhibited relatively poor solubility but better thermal stability than unhydrogenated diblock copolymers because of the polyethylene segments. Poly[(hydrochloride quaternized 2‐norbornene‐5‐methyleneamine)‐b‐butadiene]‐1 (poly 3a ) was obtained after the hydrolysis and quaternization of poly 1a . Dynamic light scattering measurements indicated that the hydrodynamic diameters of the cationic copolymer (poly 3a ) in water (hydrodynamic diameter = 1580 nm without salt), methanol/water (4/96 v/v; hydrodynamic diameter = 1500 nm without salt), and tetrahydrofuran/water (4/96 v/v; hydrodynamic diameter = 1200 nm without salt) decreased with increasing salt (NaCl) concentration. The effect of temperature on the hydrodynamic diameter of hydrophobically modified poly 3a was also studied. The inflection point of the hydrodynamic diameter of poly 3a was observed at various polymer concentrations around 30 °C. The critical micelle concentration of hydrophobically modified poly 3a was observed at 0.018 g dL^?1. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2901–2911, 2006     

Further study of the viscoelastic phase separation of cyanate ester modified with poly(ether imide)

In this study, the viscoelastic phase separation process was studied further by time‐resolved light scattering, differential scanning calorimetry, and scanning electron microscopy in the system of poly(ether imide)‐modified bisphenol‐A dicyanate. It was observed that the evolution time of phase structure and relaxation time of diffusion flow of the bisphenol‐A dicyanate were similar with the phase diagram of curing conversion versus content of PEI. The results suggested that the viscoelastic phase separation was affected by the curing conversion of the system at the onset point of phase separation. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 517–523, 2006     

Simultaneous electrochemical determination of uric acid and ascorbic acid on a glassy carbon electrode modified with cobalt(II) tetrakisphenylporphyrin.

A cobalt(II) tetrakisphenylporphyrin (Co(II)TPP) film modified glassy carbon electrode (Co(II)TPP-GCE) was prepared by just coating Co(II)TPP solution on the surface of the electrode. It can be used for the simultaneous determination of ascorbic acid and uric acid. The anodic peaks of AA and UA can be separated well. Owing to the strongly hydrophobic property of porphyrin, the modified electrode has good stability and long life. The linear range for UA and AA were 2.0 x 10(-6)-1.0 x 10(-4) M and 9.0 x 10(-6)-2.0 x 10(-3) M with detection limits of 5.0 x 10(-7) and 5.0 x 10(-6) M, respectively. Furthermore, metalloporphyrins of other kinds were also used to construct modified electrodes. Their performances were inferior compared with that of the Co(II)TPP modified electrode.     

Synergistic effect between 4-(2-pyridylazo) resorcin and chloride ion on the corrosion of cold rolled steel in 0.5 M sulfuric acid

The corrosion inhibition of 1-(2-pyridylazo)-2-naphthol (PAR) on the corrosion of cold rolled steel in 0.5 M sulfuric acid (H₂SO₄) was studied using weight loss method and potentiodynamic polarization method. Results obtained revealed that together with chloride ion, PAR is an effective corrosion inhibitor for steel corrosion in sulfuric acid. It was found that for steel corrosion inhibition in the presence of single PAR in sulfuric acid the Temkin adsorption isotherm may be used to explain the adsorption phenomenon. For the mixture of PAR and NaCl used as corrosion inhibitor, however, the Langmuir adsorption isotherm can be used to satisfactorily elucidate the adsorption of mixture of PAR and NaCl. Potentiodynamic polarization studies showed that single PAR mainly acts as a cathodic inhibitor for the corrosion of steel in 0.5 M sulfuric acid. The mixture of PAR and chloride ion, however, acts as a mixed type inhibitor that mainly inhibits cathodic reaction of the steel corrosion in sulfuric acid. By means of electrochemical polarization tests, a desorption potential at ca. −370 mV was observed for the adsorption of mixture of PAR and chloride ion, when potential reaches this value, adsorbed inhibitor molecule heavily departs from the steel surface. For the mixture of PAR and chloride ion, thermodynamic parameters such as adsorption heat, adsorption entropy and adsorption free energy were obtained from experimental data of the temperature studies of the inhibition process at four temperatures ranging from 30 to 45 °C, the kinetic data such as apparent activation energies and pre-exponential factors at different concentrations of the inhibitor were calculated, and the effect of the apparent activation energies and pre-exponential factors on the corrosion rates of cold rolled steel was discussed. The most suitable range of inhibitor concentration was discussed. The inhibitive action was satisfactorily explained by using both thermodynamic and kinetic models. Synergism between chloride ion and PAR was proposed. The results obtained from weight loss and potentiodynamic polarization were in good agreement.