Energy transfer between the flavin chromophores of electron-transferring flavoprotein fromMegasphaera elsdenii as inferred from time-resolved red-edge and blue-edge fluorescence spectroscopy

Both a mode-locked argon-ion laser and synchrotron radiation were used as excitation sources to obtain time-resolved polarized fluorescence of the two FAD cofactors in electron transferring flavoprotein fromMegasphaera elsdenii. Red-edge excited and blue-edge detected fluorescence anisotropy decay curves did not contain a fast relaxation process which was observed upon mainband excitation and detection. This relaxation was assigned to homo-energy transfer between the two FAD cofactors. Failure of energy transfer as observed with edge spectroscopy on this protein excludes restricted reorientational motion of the flavins as a possible mechanism of depolarization. From the global analysis of the fluorescence anisotropy decay surface obtained at multiple excitation and detection wavelengths, the distance between and the relative orientation of the flavins could be estimated. The methodology described has general applicability in other multichromophoric biopolymers and has the potential to acquire accurate geometrical parameters in these systems.     

Change in the nature of the Ni diffusion mechanism on the Si(111) surface with adsorption of Co atoms

The diffusion of Ni on a Si (111) surface is investigated by LEED and Auger electron spectroscopy. It is found that, in contrast to the process on the initially clean Si (111)−7×7 surface, on Si (111) surfaces with submonolayer Co coverages the nature of the Ni transport mechanism changes at a temperature of about 750 °C, and the Ni surface diffusion coefficients increase sharply below this temperature. Pis’ma Zh. éksp. Teor. Fiz. 66, No. 9, 611–614 (10 November 1997)     

Resonance effects in a phased antenna array constructed from rectangular waveguides

Translated from Matematicheskie Modeli i Optimizatsiya Vychislitel'nykh Algoritmov, pp. 131–143, 1993.     

Towards an Operational Model for Prevention and Treatment of Asthma Attacks

Asthma is one of the major chronic diseases in many countries. At present there is no cure for asthma, but medical advances can help to reduce the chances of attacks of the condition. Efficient care for asthma involves complexity, uncertainty, variability and the use of scarce resources, and these are the same conditions that indicate a possible use for the modelling approach of operational research. This paper is concerned with a pilot model that was developed through joint work by medical professionals and operational researchers. The development of the model is explained and illustrative results indicate the potential value of the modelling approach for the care of asthma in the community.     

A Note on an Input Control Model of a Predictive Regression Interval

A well-known problem of prediction in linear regression models is to find a confidence interval for the random value of the dependent variable when the values of the independent variables are given. Such a situation may arise in economic quality control models when the independent variables are costly inputs and the dependent variable is some measure of quality or production. In such a circumstance, an important control objective may be to find values for the inputs that will maximize the lower limit of the prediction confidence interval for a fixed budget, or alternatively, to minimize the cost of the inputs for a fixed lower limit of the confidence interval. In this paper, we shall show that global optima can be found using known algorithms. The special case of simple linear regression is discussed and an illustrative example is provided.     

Determination of tributyltin oxide in coastal marine sediments and mussels by electrothermal atomic absorption spectrometry

We have devised a new method for bis(tributyltin)oxide (TBTO) determination in marine sediments and mussels. This technique involves an n-hexane/methylene chloride mixture extraction and extract purification with a sodium hydroxide wash in order to eliminate interfering compounds. TBTO is then extracted again by nitric acid and converted into an inorganic tin species; the analysis has been effected using Zeeman graphite furnace-atomic absorption spectrophotometry. The method detection limit for the matrices examined is 0.004 μg TBTO g^?1 (wet weight) and is sufficient for the analysis in real samples. The percentage recovery of TBTO from sediments and mussels samples is higher than 85% and 95% respectively. This method has been applied to TBTO level determination in sediments and mussels (Mytilus galloprovincialis) sampled in the harbour area in Taranto, where mussel culture activities are much developed; the TBTO levels obtained in sediments and mussels were in the range 15-47 ng g^?1 (wet weight) and 11-30 ng g^?1 (wet weight) respectively. Such values are comparable with those found in other harbour areas in the Mediterranean Sea.     

Certification of the sulphur content of three rapeseed reference materials

Summary The sulphur content of three rapeseed reference materials has been certified on the basis of measurements made by inductively coupled plasma-optical emission spectroscopy, isotope-dilution mass spectrometry and ion chromatography. Their suitability for the calibration of x-ray fluorescence spectrometers used for measuring sulphur in rapeseed samples was established.     

Line Narrowing of a Tunable High Pressure CO2 Laser by Means of an Improved Non-Littrow Cavity

A model is reported to foresee ,for different mirror choices, the spectral properties of a high pressure, frequency tunable, CO₂ laser, operating with a non-Littrow grating mounting. The calculations show a larger frequency selectivity for not collimated plane cavities. The model is experimentally verified in a suitable high pressure laser. In particular narrowed linewidths less than 300MHz ( FWHM) are obtained.     

Arc erosion reduction on electrical contacts using transversecurrent injection

Electrical contact lifetime is often directly determined by arc erosion. A method for reducing are erosion was developed consisting of injecting from an external current source an additional electrical current flowing parallel to the contact surface. This method was examined in three are environments using the additional transverse electrical current with a density less than 1 A/mm²: 1) automobile ignition contacts; 2) pulsed air arc; and 3) low pressure (P=100 mTorr) arc in nitrogen, SEM and X-ray examination showed that application of a transverse current in a contact during arcing changed the phase composition and microstructure of the contact surface. Under optimal conditions, the microstructure which is formed is significantly more erosion resistant than without the transverse current injection