Diastereoselective formation of 2-aryl-3-arenesulfonyl 4-ethyl-1,3-oxazolidines: An X-ray crystallographic and H NMR study

N-Arylsulfonamides of (R)- and (S)-2-amino-1-butanol, on condensation with aromatic aldehydes produced diastereomerically pure 2-aryl-3-arenesulfonyl 4-ethyl-1,3-oxazolidines. The absolute configurations of one enantiomeric pair have been determined from two fully refined X-ray structures, supplemented by nmr data.     

Quantitative dependence of MR signal intensity on tissue concentration of Gd(HP-DO3A) in the nephrectomized rat.

Cardiac-gated SE 20/224 +/- 20 MR images were obtained from nephrectomized rats before and after intravenously administering 153Gd-Gd(HP-DO3A). The concentration of Gd, [Gd], was linear in dose in myocardium, skeletal muscle, and blood. Under steady-state conditions, where d[Gd]/dt = 0, image intensities (IIN) in regions of interest were compared with the measured [Gd]. IIN was linear in myocardium at less than or equal to 0.61 mumol/g-myocardium (less than or equal to 0.5 mmol/kg dose) and in skeletal muscle at less than or equal to 0.63 mumol/g-muscle (less than or equal to 0.75 mmol/kg). Above 0.6 mumol Gd/g-tissue, IIN did not increase further. The in vivo data were consistent with measured ex vivo and in vivo relaxivities. A 29% greater slope for IIN versus [Gd] in myocardium [14,439 +/- 4350 IIN (mumol/g)] than in muscle [10,258 +/- 5,296 IIN/(mumol/g)] was attributed to a significant difference in blood content: 25% versus 2% weight blood in myocardium and skeletal muscle, respectively. Two components were apparent from plots of ex vivo 1/T1 versus [Gd] in myocardium and muscle, and only one for blood.     

Design and operation characteristics of a high power transverse flow pulser sustained cw CO2 laser

A transverse flow, transverse discharge cw CO₂ laser in which de discharge is sustained by employing high repetition rate high voltage pulses has been developed. Pulser sustained discharge through electrodes of innovative design provided uniform excitation at electrical input power densities more than 10 W/cc. Laser output power more than 2.5 kW was obtained in a laser gas mixture consisting of 0.5 mbar of CO₂, 16 mbar of N₂ and 38.5 mbar of He. Design details and operational characteristics of this laser are presented.     

Studies on the curing kinetics of epoxy resins using mixture of nadic/or maleic anhydride and 4,4′-diaminodiphenyl sulfone

Curing kinetics of diglycidyl ether of bisphenol-A (DGEBA) in the presence of maleic anhydride (MA)/or nadic anhydride (NA) or mixture of MA/NA: 4,4′-diaminodiphenyl sulfone (DDS) in varying molar ratios were investigated using differential scanning calorimetry. Curing behaviour of DGEBA in the presence of varying amounts of DDS:MA/NA was evaluated by recording DSC scans at heating rates of 5, 10, 15 and 20°C min⁻¹. The peak exotherm temperature depends on the heating rate, structure of the anhydride as well as on the ratio of anhydride: DDS. Thermal stability of the isothermally cured resins was evaluated by thermogravimetry. The char yield was highest in case of resins cured using mixture of DDS:MA (0.75:0.25; sample EM-1) and DDS:NA (0.75:0.25, sample EN-1).     

HfO2/AlGaN/GaN structures with HfO2 deposited at ultra low pressure using an e‐beam

We show that HfO₂/AlGaN/GaN structures with HfO₂ layer deposited using an e‐beam in ultra high vacuum are suitable for field effect transistors. The dielectric constant of the HfO₂ was found ε_HfO > 23–24, which is close to the highest re‐ ported values for this material. The leakage current did not exceed 10^–4 A/cm² at the threshold voltage. The comparison of the losses in the samples with and without HfO₂ indicates low concentration of the interface traps. (© 2007 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Conductivity and dielectric properties of sol–gel derived porous zirconia

The 8-mol percentage Y₂O₃-stabilized Porous Zirconia was prepared using sol–gel method. Zirconium oxalate gel was prepared by the addition of appropriate amount of oxalic acid solution into the 1 M aqueous solution of zirconium-oxy chloride. A cubic phase zirconia powder was obtained by calcination and milling of the zirconium oxalate gel. Crystallization temperature was found about 450 °C from the Differential thermal analysis. The phase analysis by X-ray diffraction shows the presence of cubic phase. Pellets sintered at 1,350 °C were highly porous, and the electrical conductivity was found with lower value due to the porosity, and the hardness was about 8.0 GPa. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Simulation of Birefringence and Absorption in InGaAs-GaAs Multiple Quantum Well Acoustooptic Modulators Operating Near 980 nm

This paper presents the simulation of surface acoustic wave (SAW)-induced absorption coefficient and refractive index change in InGaAs-GaAs multiple quantum well (MQW) structures operating near 980 nm. The exciton problem is solved in two dimensional momentum space to include the non-axial effect due to strain induced valance band mixing and nonparabolicity. The optical absorption coefficient and refractive index changes near the band gap in the MQWs are calculated as a function of SAW power.     

Variation of interband interaction strength in odd-A nuclei

Bandcrossing in 31 rotational bands of 25 different odd-A nuclei in the rare-earth region has been analysed by using a two-band mixing formalism with a constant band interaction within the framework of the effective decoupling picture. The interband interaction strengthV between the one-quasiparticle band and the three-quasiparticle band exhibits a variation with the neutron number which is not different from the oscillatory behaviour observed in even-even nuclei and does not show signs of any appreciable phase shifting as predicted by theory. However, the overall range of variation ofV is greater than that observed in even-even systems.     

“Optimization of aircraft maintenance/support infrastructure using genetic algorithms—level of repair analysis”

Level of repair analysis (LORA) is an approach used during the design stage of complex equipment for analysis of the cost effectiveness of competing maintenance strategies. LORA is carried as a part of the life cycle cost and cost of ownership analysis and plays a significant role in minimizing the life cycle cost and cost of ownership of the capital equipment. Since many purchasing decisions of complex equipment are based on cost of ownership, it has become essential to carry out LORA to compete in the market. In this paper, we develop a mathematical model for LORA and propose a solution methodology based on genetic algorithms. The concept is illustrated using a hypothetical aircraft engine.