Determination of arsenic in diesel, gasoline and naphtha by graphite furnace atomic absorption spectrometry using microemulsion medium for sample stabilization

A procedure for the determination of As in diesel, gasoline and naphtha at μg L⁻¹ levels by GFAAS is proposed. Sample stabilization was achieved by the formation of three component solutions prepared by mixing appropriate volumes of the samples propan-1-ol and nitric acid aqueous solution. This mixture resulted in a one-phase medium, which was indefinitely stable. No changes in the analyte signals were observed over several days in spiked samples, proving long-term stabilization ability. The use of conventional (Pd) and permanent (Ir) modification was investigated and the former was preferred. Central composite design multivariate optimization defined the optimum microemulsion composition as well as the temperature program. In this way, calibration using aqueous analytical solutions was possible, since the same sensitivity was observed in the investigated microemulsion media and in 0.2% v/v HNO₃. Coefficients of correlation larger than 0.999 and an As characteristic mass of 22 pg were observed. Recoveries (n=4) obtained from spiked samples were 98±4, 99±3 and 103±5%, and the limits of detection in the original samples were 1.8, 1.2 and 1.5 μg L⁻¹ for diesel, gasoline and naphtha, respectively. Validation was performed by the analysis of a set of commercial samples by independent comparative procedures. No significant difference (Student’s t-test, p<0.05) was observed between comparative and proposed procedure results. The total determination cycle lasted 4 min for diesel and 3 min for gasoline and naphtha, equivalent to a sample throughput of 7 h⁻¹ for diesel and 10 h⁻¹ for gasoline and naphtha.     

A photo-oxidation procedure using UV radiation/H2O2 for decomposition of wine samples — Determination of iron and manganese content by flame atomic absorption spectrometry

This paper proposes the use of photo-oxidation with UV radiation/H₂O₂ as sample pretreatment for the determination of iron and manganese in wines by flame atomic absorption spectrometry (FAAS). The optimization involved the study of the following variables: pH and concentration of buffer solution, concentrated hydrogen peroxide volume and irradiation time. The evaluation of sample degradation was monitored by measuring the absorbance at the maximum wavelength of red wine (530 nm). Using the experimental conditions established during the optimization (irradiation time of 30 min, oxidant volume of 2.5 mL, pH 10, and a buffer concentration of 0.15 mol L^− 1), this procedure allows the determination of iron and manganese with limits of detection of 30 and 22 μg L^− 1, respectively, for a 5 mL volume of digested sample. The precision levels, expressed as relative standard deviation (RSD), were 2.8% and 0.65% for iron and 2.7% and 0.54% for manganese for concentrations of 0.5 and 2.0 mg L^− 1, respectively. Addition/recovery tests for evaluation of the accuracy were in the ranges of 90%–111% and 95%–107% for iron and manganese, respectively. This digestion procedure has been applied for the determination of iron and manganese in six wine samples. The concentrations varied from 1.58 to 2.77 mg L^− 1 for iron and from 1.30 to 1.91 mg L^− 1 for manganese. The results were compared with those obtained by an acid digestion procedure and determination of the elements by FAAS. There was no significant difference between the results obtained by the two methods based on a paired t-test (at 95% confidence level).     

Stereospecific Synthesis of Steroidal 20,16-γ-Carbolactones

Two strategies have been explored for the synthesis of steroidal 20,16-γ-carbolactones from the corresponding 17-ketoandrostane. A highly efficient, stereospecific protocol has been developed for the β-oriented cis-γ-lactone, based on a Michael addition of cyanide to a conjugated ketone. A different approach, involving prior attachment of a 3-carbon side chain on C-17 of a 17-oxo-16β-acetoxy-androstane led to the epimeric, α-oriented lactone.     

Preparation and structure of three solvatomorphs of the polymer [Co(dbm)2(4ptz)]n: spin canting depending on the supramolecular organization

The syntheses and X-ray structures of three isomeric 1D coordination polymers are reported. The complex [Co(dbm)2(MeOH)2] (1) was used as a precursor in these reactions. The preparation and structure of 1 is also presented; this mononuclear complex is in the cis configuration because this allows the formation of a network of intermolecular hydrogen bonds in the solid state. Reaction of 1 with 2,4,6-tris-(4-pyridyl)-1,3,5-triazine (4ptz) yields the polymers [Co(dbm)2(4ptz)]n.nTHF (2a), [Co(dbm)2(4ptz)]n.0.75nTHF.0.5nEt2O (2b), and [Co(dbm)2(4ptz)]n.3nDMF (2c) in the form of zigzag chains, instead of the expected honeycomb architectures. This is because of the establishment of extended pi-pi stacking throughout these solids, which could not have occurred otherwise. Compounds 2a, 2b, and 2c are solvatomorphs, and formation of either one of them depends on the exact conditions of crystallization, which lead to significant differences in the supramolecular organization of the chains. Bulk magnetic measurements on 2a reveal weak antiferromagnetic exchange within the chains and small ordering throughout the solid that results in the manifestation of the phenomenon of spin canting, whereas for 2c the different supramolecular organization causes the antiferromagnetic exchange not to result in spin canting.     

Copper acetylacetonate anchored onto amine-functionalised clays

Copper (II) acetylacetonate was immobilised directly onto two clays, laponite (Lap) and K10-montmorillonite (K10), and after their amine functionalisation with (3-aminopropyl)triethoxysilane (APTES). All the materials were characterised by nitrogen adsorption isotherms at -196 degrees C, elemental analysis, TG-DSC, XRD, and IR spectroscopy. The K10-based materials were also characterised by XPS. The APTES-functionalised K10 showed higher copper loading than K10, indicating that the clay functionalisation enhanced the complex immobilisation; on the contrary, in Lap-based materials higher metal content was obtained by direct complex anchoring, probably due to the delaminated nature of Lap which induced the particles aggregation on functionalisation with APTES. All the results pointed out that the Cu complex was anchored onto the amine-functionalised clays by Schiff condensation between the amine groups of anchored APTES and the carbonyl groups of the acetylacetonate ligand, whereas direct immobilisation proceeded mostly through interaction between the metal centre and the clay surface hydroxyl groups.     

The carboxylate shift in zinc enzymes: a computational study

Zinc is the second most abundant transition element in biology and the only metal known to be represented in enzymes from each one of the six classes established by the International Union of Biochemistry. The flexible coordination geometry, the fast ligand exchange, the lack of redox activity, and its role as Lewis acid are just some of the features that make zinc an invaluable element in biological catalysis. In this study, we have analyzed the importance in mononuclear Zn enzymes of an interesting mechanistic phenomenon known as carboxylate shift, which is characterized by a change in the coordination mode of a carboxylate group (mono to bidentate or vice versa) with both ligand entrance or exit from the metal coordination sphere. Using B3LYP calculations, we were able to unveil in detail patterns relating the intrinsic characteristics of a given Zn coordination sphere with the existence or not of a carboxylate-shift mechanism and the additional energy stabilization arising from it. In particular, a specific Zn coordination sphere containing a carboxylate ligand (Asp or Glu), a cysteine, and a histidine has been shown to have the most favorable combination of amino acid residues that ensures a fast ligand exchange.     

Basis set and method dependence in quantum theory of atoms in molecules calculations for covalent bonds

The influence of various small- and medium-size basis sets used in Hartree-Fock (HF) and density functional theory (DFT)/B3LYP calculations on results of quantum theory of atoms in molecules based (QTAIM-based) analysis of bond parameters is investigated for several single, double, and triple covalent bonds. It is shown that, in general, HF and DFT/B3LYP methods give very similar QTAIM results with respect to the basis set. The smallest 6-31G basis set and DZ-quality basis sets of Dunning type lead to poor results in comparison to those obtained by the most reliable aug-cc-pVTZ. On the contrary, 6-311++G(2df,2pd) and in a somewhat lesser extent 6-311++G(3df,3pd) basis sets give satisfactory values of QTAIM parameters. It is also demonstrated that QTAIM calculations may be sensitive for the method and basis set in the case of multiple and more polarized bonds.     

The fractal dimension as estimator of the fractional content of metal matrix composite materials

Electrochemical techniques are applied to estimate the fractal dimension value of electroactive surface structures. However, the fractal dimension value is an abstract concept, which sometimes is hard to understand. Herein, this abstract concept is used to calculate the fractional content of the nickel/graphite–polypropylene hybrid composite material, putting into practice this concept in the study of composite materials.