甲基肼/四氧化二氮反应化学动力学模型构建及分析

甲基肼(MMH)和四氧化二氮(NTO)是常用的液体火箭发动机推进剂,但目前对其反应机理的研究还十分有限.本文首先构建了一个包含23种组分和20个基元反应的MMH/NTO反应动力学模型;对MMH/NTO自燃着火过程进行的验证计算表明,该机理能够合理地描述MMH/NTO的自燃温升过程,准确预测反应物系统的着火延迟时间及平衡温度,并能合理地反映MMH/NTO反应物系统着火延迟时间对反应初始压力以及氧燃比的依赖关系;通过灵敏度分析方法指出了影响MMH/NTO着火过程的关键反应.模拟分析了在不同压力和氧燃比条件下MMH/NTO系统的自燃温升过程,结果表明,随着压力的升高,系统着火延迟时间变短,平衡温度升高;在一定范围内增大氧燃比,着火延迟时间变长,平衡温度先升高后减小.     

Characterization of PdO/Ce0.8Y0.2O1.9 catalysts for carbon monoxide and methane oxidation

The Ce_0.8Y_0.2O_1.9 solid solution was prepared by nitrate sol–gel method, and a series of catalysts with different PdO loading were prepared using impregnation method. These catalysts were characterized by XRD, Raman, CO-TPR, CO₂- and O₂-TPD techniques. The PdO is highly dispersed on the surface of the solid solution when the loading is lower than 0.5 wt.%. As PdO loading increases to 2 wt.%, it begins to form the crystalline structure. CO₂-TPD profiles show that the CO adsorbed on highly dispersed PdO is more easily oxidized to CO₂ than that adsorbed on crystalline structure and O₂-TPD results indicate that it is more difficult to decompose for highly dispersed PdO than that for crystalline structure. CO-TPR profiles show that the highly dispersed PdO is easily reduced. Catalytic activities of these catalysts for CO and CH₄ oxidation indicate that both the highly dispersed and crystalline PdO are the active site for CO oxidation, while the crystalline structure is the active site for CH₄ oxidation.     

Ir/CeO2催化剂的表征和CO氧化性能

采用浸渍法制备了Ir/CeO2催化剂,考察了催化剂的CO氧化活性。随着Ir负载量的增加,Ir/CeO2催化剂的CO氧化活性先上升后下降,当Ir的负载量为1%时,催化剂的活性最高。Ir/CeO2催化剂中Ir以IrO2的形式存在,当低负载量(≤1%)时以高分散形式存在;高负载量(>1%)时以晶相IrO2的形式存在。随着Ir负载量增加,Ir粒子逐渐变大,反应比速率和反应转换频率(TOF)逐渐下降,表明小粒子上具有更高的CO反应活性。同时也发现金属态Ir催化剂的CO氧化活性高于氧化态IrOx催化剂。     

Ir/ZrO2催化剂对甲烷催化燃烧性能的研究

采用浸渍法制备了ZrO₂为载体负载Ir的催化剂(Ir/ZrO₂), 考察了催化剂的CH₄催化燃烧性能. 采用X射线衍射(XRD), 拉曼光谱(Raman), X射线光电子能谱(XPS), 氢气程序升温还原(H₂-TPR)等技术对催化剂的结构和Ir物种的存在形式进行了表征. 结果表明, Ir/ZrO₂催化剂中Ir是以IrO₂形式存在的, Ir/ZrO₂催化剂的CH₄燃烧表观活性随着Ir负载量的增加而提高, 并且催化剂表现出较高的催化活性和良好的反应稳定性. 在低Ir负载量(≤1%)时, CH₄燃烧的转换频率(TOF)随着Ir粒子的增大而提高|然而高Ir负载量(≥1%)时, TOF随着Ir粒子的增大保持不变.     

金属配合物Cd（phen）2（NO3）（NO2）对ZnO光阳极的敏化特性

采用具有紫外光区吸收的金属配合物Cd(phen)2(NO3)(NO2)和N719对ZnO光阳极进行共敏化.结果表明,配合物能够对ZnO光阳极进行共敏化,同时被电解液还原再生,共敏化增加电池对光的吸收,电池光电流密度增加63%,共敏化降低了电池各个界面电阻,有利于电子在界面的传输,电池的光电转换效率提高了37%.     

Synthesis of thermally stable zirconia-based mesoporous materials via a facile post-treatment

A novel method of preparing thermally stable zirconia-based mesoporous materials was developed. The zirconia-based mesoporous materials of 2D-hexagonal structure were prepared using zirconium sulfate as the zirconium precursor and cetyltrimethylammonium (CTMA) as the pore-directing agent with the aid of salt in the synthesis solution to reduce the sulfate content in the final product and significantly improve the crystallographic ordering. Post-treatment of the mesoporous material with NaCl solution and lowering the ramping rate to less than 0.2 degrees C/min during the calcination process, however, were the key steps to hinder the growth of the dense zirconia phase and to retain the ordered mesostructure up to 600 degrees C. It was found that a portion of the surfactant (8.9-17.4 wt %) and sulfate ions (0.5-1.2 wt %) were removed during the post-treatment, which prevented the remaining sulfate groups from being reduced by the hydrogen-rich surfactant during the calcination process as confirmed by sulfur K-edge X-ray absorption near edge structure (XANES) and infrared spectroscopy. The maintenance of sulfur in the sulfate state seemed to be important in stabilizing the mesoporous structure of zirconia materials. The mesoporous zirconia materials after extraction with NaCl solution three times and calcination at 550-600 degrees C had the composition ZrO(2-x)(SO4)x with x = 0.10-0.27. The material possesses high surface area (approximately 200 m2/g), large pore volume (approximately 0.10 cm3/g), and wormlike mesopores. In comparison with the mesoporous zirconia materials stabilized by chemical treatment, the present route was simpler and more environmentally friendly and resulted in mesoporous zirconia materials of better thermal stability.     

硅/石墨复合物用作锂离子电池负极材料

以石墨和纳米硅粉为原料, 利用机械球磨的方法制备了硅/石墨复合物, 用作锂离子电池负极材料. 采用XRD, SEM以及电化学测试等手段对材料进行了结构表征和性能测试. 通过球磨不同质量比的硅和石墨, 并对相应的复合物进行充放电测试, 寻找到了硅和石墨的最佳比例, 其值为1∶9. 实验结果表明, 所得材料既具备高于纯纳米硅的循环性能, 又具有比石墨高的可逆容量.     

Fabrication of nanorattles with passive shell

This investigation describes the formation of a metal nanorattle with a pure metal shell by varying experimental parameters. The galvanic replacement reaction between silver and chloroauric acid was adopted to prepare hollow metal nanoparticles. This approach is extended to produce nanorattles of Au cores and Au shells by starting with Au(core)Ag(shell) nanoparticles as templates. The effect of temperature on the nanostructure of the final product is also considered. The composition of the shell in nanorattles can be controlled by varying the reaction temperature (to form pure gold or gold-silver alloy, for example). X-ray absorption fine structure spectroscopy is conducted to elucidate the fine structure of these nanoparticles. Partial alloying between the Au core and the Ag shell is observed by extended X-ray absorption fine structure (EXAFS).     

Electrochemical behaviour of ferrocenyl-containing acyl thiourea derivatives

Twenty four N-ferrocenoyl-N-aryl(alkyl or ferrocenyl) thiourea derivatives were prepared and ten of them investigated by cyclic voltammetric method in DMF or CH2Cl2 solutions. The compounds exhibit a higher redox potential than ferrocene. Although distant from the redox centre, the substituents on N can influence the redox potential of ferrocenyl via intramolecular hydrogen bonding.