Extraction and verification of coherent structures in near-wall turbulence

According to the characteristics of coherent structures in near-wall turbulence, an accurate extraction and verification method is developed based on wavelet transform (WT) and correlation analysis in this paper. At first, the fluid field of a turbulent boundary layer is measured precisely in a gravitational low-speed water tunnel. On the basis of the distribution of the coherent structures, velocity data of three test points are selected and analyzed, whose dimensionless heights are 20.8, 33.5, and 42.6. According to the frequency range of power spectrum density (PSD), coherent and incoherent structures are both extracted from the original signals using continuous and orthogonal wavelet transforms. To confirm the validity of the extracted signals, the probability density function (PDF) of each extracted signal is calculated. The result demonstrates that the incoherent structures obey the Gaussian distribution, while the coherent structures deviate from the Gaussian distribution. The PDFs of the coherent structures and the original signals are similar, which shows that the coherent structures make most contributions to the turbulence. For further verification, a correlation parameter between coherent and incoherent structures is defined, which evidently proves the validity of the extraction method in this paper.     

Beam Combination using Stimulated Brillouin Scattering for the Ultimate High Power-Energy Laser System Operating at High Repetition Rate over 10 Hz for Laser Fusion Driver

After the laser was invented in 1960, a phase conjugation mirror has been respected to be the most fantastic one for the laser resonator composition because it can compensate any distortions of the laser beams occurred by the many inhomogenuities of the laser media and optical components. Among the many phase conjugation configurations, the stimulated Brillouin scattering phase conjugation mirror is the most simple one and many researchers have tried to utilize it to develop high power/energy laser systems. For realizing a high energy/power laser system the thermal problem is the most difficult to solve, and some researchers suggested a beam combination technique to reduce the thermal load of the big laser media to many small sized ones. To accomplish the beam combination using stimulated Brillouin scattering phase conjugation mirrors (SBS-PCMs), it is necessary to lock/control the phases of the SBS-PCMs. And some researchers have developed several ways for it, but they can lock the phases of a limited number of beams overlapped at the foci less than 5, or lock the phases by back-seeding technique but it loses the phase conjugation characteristics. For realization of the laser fusion driver, it is necessary to combine more than 10 or 100 beams. And the authors have developed recently a new phase controlling/locking technique which is isolated and independent totally from other beams and it can be applied to an unlimited number of beams in principle.     

某型飞机驾驶杆线性位移差分变压器传感器信号调理校正

飞机驾驶杆LVDT(线性位移差分变压器)传感器信号测试校正在航空测控研究领域具有十分重要的意义,提出了一种针对某型飞机驾驶杆LVDT传感器信号精确调理校正方法;介绍了飞机驾驶杆LVDT传感器原理,分析了AD598 LVDT调理芯片的使用局限,利用最小二乘法设计了精确调理校正方法;基于VC++2010开发环境,利用高精度的模拟校正源产生模拟激励校正信号,设计了驾驶杆LVDT多通道软件自校正方法,它可以有效提高解调电路的线性度和对称性,克服了AD598常规调理电路的使用局限,从而实现驾驶杆LVDT信号精确检测;理论分析与数值试验验证了所提方法的正确性和有效性。     

点式单波束多普勒测流系统的设计方法

为了加快多普勒流速计算速度和提高系统稳定性,提出基于FPGA技术的多普勒测速的设计方法,其中包括信号发射电路和信号接收电路。首先通过M码进行二相相移键控信号的调制,减少了回波误差、增加信号发射能量,有效地降低了水中超声波的能量耗散对信号提取的影响。然后对回波信号进行二相解调,并利用复自相关算法进行分析处理。最后,通过测速实验对所提方法进行验证。实验结果表明,所提方法不仅具有较低的实验误差而且具有较高的可靠性。     

源气体对沉积的a-C∶F∶H薄膜结构的影响

采用微波电子回旋共振等离子体化学气相沉积(MWPECRCVD)方法,使用不同的源气体(CHF3CH4,CHF3C2H2,CHF3C6H6)体系制备了aC∶F∶H薄膜.由于CH4,C2H2,C6H6气体在等离子体中的分解反应不同导致了薄膜的沉积速率和结构上的差异.红外吸收谱的结果表明,用C6H6CHF3作为源气体沉积的薄膜中几乎不含H,而用C2H2CHF3所沉积的薄膜中的含氟量最高,其相应的CF振动峰位向高频方向偏移.薄膜的真空退火结果表明,aC∶F∶H薄膜的热稳定性除了取决于薄膜的CC键浓度外,还与CC键 关键词： 氟化非晶碳膜 电子回旋共振化学气相沉积 红外吸收光谱     

KNSBN晶体猫式互抽动相位共轭光特性

在KNSBN：Ce晶体中，利用二波耦合作用，在单一光束无法获得相位共轭光的条件下，实现了“猫”式互抽运相位共轭光输出，获得较高的共轭光发射率，实验结果表明，晶体的二波耦合作用可以使晶体的自抽运相位共轭光的阈值光强降低。入射光的入射角范围增大，响应时间缩短。     

PMP泡沫的飞秒激光烧蚀及切割方法

对密度为90 mg/cm3的PMP泡沫材料的飞秒激光烧蚀结果进行了分析,推导出该材料在脉宽50 fs、波长800 nm、重复频率为1000 Hz的飞秒激光作用下的蚀除阈值为0.91 J/cm2（100个激光脉冲）,获得了烧蚀直径分别随激光功率、脉冲数及聚焦物镜数值孔径的变化规律。相同飞秒激光加工系统下,对比了铜箔上获得的烧蚀形状,确定了PMP泡沫材料本身的多孔洞及其分布不均匀是造成烧蚀区域的形状不规则的重要因素。PMP泡沫在较高能量或是较长时间的飞秒激光作用下,烧蚀区域发生碳化的原因是由热作用引发的。提出了一种基于激光束耦合的飞秒激光切割厚度大于1 mm的薄膜-泡沫材料的方法,并获得了切割厚度大于1.5 mm、切割侧壁与光束光轴夹角小于5、切割面整洁的薄片。     

Mg掺杂PST薄膜的溶胶-凝胶法制备及晶相形成研究

利用溶胶-凝胶法成功制备了Mg掺杂Pb_0.4Sr_0.6Mg_xTi< sub>1-xO_3-x薄膜，利用x射线衍射仪对薄膜的物相和结构进行了分析， 用扫描电子显微镜对薄膜的形貌和断面等进行了观察.研究结果表明，薄膜以立方钙钛矿为 晶相，薄膜中晶相以团聚状颗粒存在，晶相含量受热处理条件和Mg的掺杂量所控制.Mg掺杂 对Pb_0.4Sr_0.6Mg_xTi_1-xO_3-x 薄膜晶相含量的影响与钙钛矿中的氧空位缺陷相关.在一定的掺杂范围内，由掺杂引起晶相 的晶格畸变较小时，体系掺Mg平衡了晶体内本征氧空位引入的电荷不平衡，使晶相更为稳定 ，析晶能力提高，晶体形成量随掺杂浓度的提高而提高.当掺杂浓度达到一定量时， 随着Mg 掺杂浓度增加，一方面使形成晶体时杂质浓度增加造成参与形成晶相的组成含量下降，另一 方面使进入钙钛矿结构的Mg增加，氧空位大量增加使畸变程度提高，形成的晶相不稳定，析 晶能力下降，晶体含量随掺杂Mg浓度的增加而不增反降.在相同条件下制备的Pb_{0.4Sr0.6MgxTi1-xO3-x薄膜中Mg掺量约为 x=0.01时，得到的钙钛矿相含量最高，本征氧缺陷所带入的正电荷和Mg引入时带入的负电荷 间达到平衡.此外，Mg的掺入还影响到析晶与热处理过程之间的关系.在高Mg掺量范围，Mg含 量越高，形成的晶相越不稳定，热处理时间越长，使热处理过程中分解的晶相量越多，随Mg 掺量越高和热处理时间越长，薄膜中晶相含量越低. 关键词： 溶胶-凝胶法 PST薄膜 Mg掺杂 晶相形成}     

半色调荧光图像的光谱反射与透射模型

荧光油墨半色调印刷品的显色预测规律是彩色成像领域内十分关键的课题。把荧光半色调印刷品反射出来的光分成两个独立的部分,即由最初入射光组成的主光流和由于吸收了主光流而产生的荧光流;并且采用了一个指数矩阵来描述墨层产生的荧光光强,从而得出了荧光半色调图像色彩的光反射规律。考虑到入射光中从一种颜色油墨入射后再由同色油墨出射的概率要比从其它色油墨出射的概率要大的事实,讨论中引入权重因子描述从同色油墨出射部分与从整个表面出射部分比例不同的现象,建立了荧光油墨半色调图像的Clapper-Yule新光谱反射率模型。     

175Er的衰变纲图

用14MeV中子照射天然Yb靶,通过¹⁷⁶Yb(n,2p)¹⁷⁵Er反应产生了新的重丰中子同位素¹⁷⁵Er,借助X-γ,γ-γ符合测量方法,首次鉴别出了¹⁷⁵Er,并测得其半衰期为(1.2±0.3)min.同时还观察到了¹⁷⁵Er衰变所发射的8条新γ射线,建立了¹⁷⁵Er的部分γ衰变纲图,从中指定了¹⁷⁵Tm的一个基态转动带.