Study of the dynamic structure factor of strong glasses

The dynamic structure factors (DSFs) of several strong glasses (SF6, SF10, BK7, SUPRASIL) measured by Brillouin light scattering spectroscopy are reported. Spectra have been collected, at and above room temperature, at two scattering angles, θ=90° and θ=180° corresponding to exchanged wavevector q values ranging from 0.0256 to 0.0448 nm⁻¹. In particular we find that the isotropic spectral lineshapes are in all cases well described by the simple hydrodynamic theory of an amorphous solid. The width of the Brillouin peaks are found to be consistent with the predicted q² dependence at both investigated temperatures. This damping is however found to account only partially for the strong asymmetry of the Brillouin line clearly visible on a logarithmic intensity scale. As a matter of fact there is an excess intensity in the very low frequency plateau underlying the central component. The height of this plateau and hence the entire lineshape is well reproduced if a relaxation process is taken into account in the hydrodynamic equations. Owing to the intense elastic scattering we are able to determine unambiguously only the ratio between amplitude and characteristic time of this process which quantifies the sound dispersion to be of the order of a few percent in all samples. The temperature dependence of the parameters indicates that this relaxation cannot be attributed to thermally activated relaxation phenomena. These general findings favorably compare with molecular dynamics simulation results on similar systems.     

On the Validity of Clauser and Horne Factorizability

The Clauser–Horne approach used to derive experimentally measurable quantities for performing experiments on EPR paradox based on Type-I Spontaneous Parametric Down Conversion (SPDC) sources is discussed. It is proved that in this case the deduced Bell's type inequality does not correctly express separability and causality. A deeper analysis of the problem shows that the Clauser–Horne hypothesis of factorizability of joint detection probability cannot be considered so general as to describe this physical situation.     

Rheological and Electrical Properties of Oxidized Carbon Black Suspensions in Vaseline Oil under Shear and Vibration

The results of investigations of the rheological characteristics and electrical resistance of the suspensions of carbon black in vaseline oil under the effects of shear and vibration were presented. The investigations are carried out on an original unit that allowed one to simultaneously subject the suspensions to shear deformation and orthogonal vibration. The electrical resistance was also measured in an ac pulsed low-voltage mode. Possible mechanisms of the suspension conductivity were considered depending on the regime of dynamic action.     

The honors class: hilbert’s problems and their solvers

Feel like writing a review for The Mathematical Intelligencer? You are welcome to submit an unsolicited review of a book of your choice; or, if you would welcome being assigned a book to review, please write us, telling us your expertise and your predilections.     

Numerical Prediction of the Strain State of Thermoset Matrix/Mineral Filler Composite Plates

The numerical prediction of the fields of inelastic strains (the linear invariant of the tensor of inelastic strains) in thermoset polyester/marble filler composite plates is discussed. A uniformly distributed load is applied to the plates, which lie on a steel base. The strain fields are predicted by means of the boundary element method by using creep test data for the composites and the polyester matrix itself. Identical creep tests were performed for two ages of the materials (1 month and 13 years), which allowed evaluating the aging effect. The study is carried out in two stages. At the first stage, the application of the generalized Maxwell-Gurevich equation to the thermoset matrix/mineral filler composite is demonstrated. The model parameters determined from the experimental creep data is used for the second stage, where the state of inelastic strains in the plates is predicted by applying the boundary element method. The influence of composite formulation (filler content) and physical aging of the polyester matrix on the state of inelastic strains in the plates is shown.__________Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 41, No. 2, pp. 145–156, March–April, 2005.     

Polarized Lidar Reflectance Measurements of Vegetation at Near-Infrared and Green Wavelengths

There is growing interest in the use of lidar for remote sensing of vegetation owing to the emergence of reliable and rugged lasers and highly sensitive detectors. Lidar remote sensing has a distinct advantage over conventional techniques in vegetation remote sensing due to its capability for three-dimensional characterization of vegetative targets. The Multiwavelength Airborne Polarimetric Lidar (MAPL) system was developed primarily for vegetation remote sensing applications from an airborne platform of up to 1,000 -m altitude. The lidar system has full waveform capture and polarimetric measurement capability at two wavelengths in the near-infrared (1064 nm) and the green (532 nm) spectral regions. This study presents preliminary ground-based lidar reflectance measurements on a variety of deciduous and coniferous trees under fully foliated conditions with a view towards tree species discrimination. Variations in the reflectance characteristics of selected deciduous trees under unfoliated and fully foliated conditions were also investigated. Our study reveals distinct differences in the reflectance characteristics of various trees.     

Hybrid numerical—experimental approach for investigation of dynamics of microcantilever relay system

The time average holography measurements of the vibrating microelectromechanical switch (MEMS) were performed in this study. Experimental measurement results exhibit good agreement with computer generated holographic interferogram analysis. The validation of experimental investigations versus numerical analysis provides the necessary background to analyze the dynamical characteristics of micromechanical systems in virtual numerical environments. Direct application of fringe counting techniques for reconstruction of motion from time average holograms cannot be straightforward if the analyzed micromechanical systems contain motion limiters. Modifications of a classical time average holographic technique enable qualitative analysis of MEMS and can be applied for investigation of dynamical properties of much broader classes of MEMS systems.     

The g-values of defects in hydrogenated microcrystalline silicon

The anisotropic g-values of defects in hydrogenated microcrystalline silicon prepared by hot-wire chemical vapour deposition have been measured as a function of crystalline volume fraction at room temperature. The defect has been identified as a silicon-dangling bond existing on the surface of crystalline grain. Their anisotropic g-values are discussed in the light of theoretical calculations by Ishii et al. and Ishii and Shimizu. The defect density is also discussed as a function of crystalline volume fraction.     

The dynamics of excitons and trions in resonant tunneling diodes

The aim of this work is to study the dynamic formation and dissociation of trions and excitons in double barrier resonant tunneling diodes. We propose a system of rate equations that takes into account the formation, dissociation and annihilation of these complexes inside the quantum well. From the solutions of the coupled equations, we are able to study the modulation of excitons and trions formation in the device as a function of the applied bias. The results of our model agree qualitatively with the experiments showing the viability of these rate equations system to study the dynamics of complex systems.     

Closed-form solutions for a rectangular layer with central crack under anti-plane shear stress

We consider the problem of determining the stress distributionin a finite rectangular elastic layer containing a Griffithcrack which is opened by internal shear stress acting alongthe length of the crack. The mode III crack is assumed to belocated in the middle plane of the rectangular layer. The followingtwo problems are considered: (A) the central crack is perpendicularto the two fixed lateral surfaces and parallel to the othertwo stress-free surfaces; (B) all the lateral surfaces of therectangular layer are clamped and the central crack is parallelto the two lateral surfaces. By using Fourier transformations,we reduce the solution of each problem to the solution of dualintegral equations with sine kernels and a weight function whichare solved exactly. Finally, we derive closed-form expressionsfor the stress intensity factor at the tip of the crack andthe numerical values for the stress intensity factor at theedges of the cracks are presented in the form of tables.