论恒力作用下质点的相对论运动

在相对论情况下，讨论了受恒力作用的质点的运动规律。     

Slutsky定理的一个推广

本文应用紧集上的连续函数是一致连续的性质，推广并证明了著名的Slutsky定理。     

类铍离子低激发态等电子系列的能量、精细结构和超精细结构

采用多组态相互作用方法及Rayleigh-Ritz 变分方法，并考虑相对论修正和质量极化效应，获得了类铍离子等电子系列（Z=4-10）低激发态1s²2p2p ¹D^e和1s²2p3p ³P^e的相对论能量。同时还计算了精细结构和超精细结构。计算结果与其他理论和实验符合的很好。     

From a Nonlinear, Nonconvex Variational Problem to a Linear, Convex Formulation

   Abstract. We propose a general approach to deal with nonlinear, nonconvex variational problems based on a reformulation of the problem resulting in an optimization problem with linear cost functional and convex constraints. As a first step we explicitly explore these ideas to some one-dimensional variational problems and obtain specific conclusions of an analytical and numerical nature.     

A Dominated Theorem on 5L(2, R) and Its Application

In this paper, we give the following dominated theorem: Let φ(g) ∈ L1(G//K),φε(t)=ε> 0, and the least radical decreasing dominatedfunction φ(t) = sup |φ(y)| ∈L1(G//K). If shtφ(t) is monotonically decreasingon (0, ∞), then for any f∈L1loc(G//K) , the following inequality holds:sup |φε * f(x)| ≤ Cmf(x),where mf(x) is the Hardy-Littlewood maximal function of f, and C = ||φ||1.An application of this dominated theorem is also given.     

System Identification Models of the Equivalent Permittivity for Rain Medium

The dielectric constant for rain medium is investigated by utilizing the system identification method. The rain rate model and frequency model of permittivity in millimeter waves band for rain medium are presented. The results obtained with models are in very good agreement with references in calculating the attenuation of electromagnetic waves induced by rain, which Shows that the obtained models are valid and practicable. The cross-polar discrimination gotten with rain rate model is in agreement with references.     

声诱饵仿真试验系统

文章介绍了声诱饵仿真试验系统中的有关问题，包括：系统的组成、工作原理、对接装置结构等。建立了对接装置声耦合状态下的数学模型，对近场声压分布进行了仿真计算，得出了匹配材料厚度、发射和接收换能器的选取原则。     

Förster energy transfer from poly(arylene–ethynylene)s to an erbium–porphyrin complex

We study the infrared emission at 1.54 μm of an organolanthanide complex, Er(III)-tetraphenylporphyrin [Er(TPP)acac], both as a result of direct optical excitation and via energy transfer from host π-conjugate polymers of type poly(arylene–ethynylene) [PAE]. In the first case, the emission of the neat complex is characterized in inert transparent materials and a value of the quantum yield at 1.54 μm φ_IR=4×10⁻⁴ is measured. Then, fluorescence resonance transfer is investigated in blends of Er(TPP)acac with PAEs by monitoring the quenching of the polymer fluorescence along with the enhancement of both the visible emission of the ligand and the near-infrared band of Er³⁺. These different procedures allow a detailed analysis of the transfer efficiency within a specific implementation of the Förster model for polymeric donors. The experimental values of the critical radius R₀, ranging from 1.3 to 2.5 nm for the different blends, are in good agreement with theory for a wide interval of the physical and spectroscopic parameters. This suggests that other mechanisms for excitation transfer do not play a significant role in these materials.     

乌桕类可可脂结晶过程中表现体积变化

为了解乌桕类可可脂(CTCBE)缓冷结晶横向胀罐爆裂原因，研究CTCBE结晶过程中的膨胀特性，采用流体静力法测试了不同等温结晶条件下CTCBE结晶形成的表观密度和表观体积及其横纵向膨胀状况。结果表明，CTCBE缓冷结晶后形成外部和中部两个晶区。在5-25℃的各等温结晶范围内，当结晶温度增加时，外部结晶区域减小、表观密度变化不大；中部结晶区域增大、表观密度明显减小，CTCBE的表观体积、横向、纵向膨胀率均增大，膨胀横向大于纵向。进一步表明CTCBE在自然缓冷固化的表观体积根本上由其结晶温度决定。为有效防止横向胀罐，自然缓冷固化温度应低于10℃。     

Resistivity－temperature characteristics of sol gel YBa2Cu3Oy samples synthesized in flowing oxygen atmosphere

The relationship of resistivity versus synthesizing temperature of sol gel YBa_2Cu_3O_y samples was studied when prepared under flowing oxygen conditions. A set of high-temperature ρ－T curves was obtained for the whole process. After the sample finished the test measuring, its resistivity was ρ_{300}=9.83×10^{-3 }Ω·cm at room temperature. The ρ－T curve also showed that the orthorhombic－tetragonal phase transformation of sol-gel YBa_2Cu_3O_y sample occurred at 581℃ for the sample in the rising temperature process, but at 613℃ in the cooling process, lower than that of the samples made by using the conventional powder metallurgy methods.