纯锆上离子注入钇和镧后的表面分析

用金属蒸汽真空弧源，以40kV加速电压对纯锆样品分别进行了10¹⁶—10¹⁷/cm²的钇、镧离子注入，注入温度约为130℃.然后对注入样品进行表面分析.x射线光电子能谱分析表明，注入的钇以Y₂O₃形式存在，镧以La₂O₃形式存在.俄歇电子能谱表明，纯锆基体表面的氧化膜厚度随着离子注入剂量的增加而增加，当离子注入剂量达到10¹⁷/cm²时，氧化膜的厚度达到了最大值.卢瑟福背散射显示镧层的厚度约为30nm，同时直接观察到当离子注入剂量为(La+Y)10¹⁷/cm²时，纯锆样品表面发生了严重的溅射. 关键词： 纯锆 钇和镧离子共注入 卢瑟福背散射 x射线光电子能谱     

Cluster and periodic DFT calculations of adsorption and activation of CO2 on the Cu(hkl) surfaces

The adsorption behavior and thermal activation of carbon dioxide on the Cu(1 1 1), Cu(1 0 0), and Cu(1 1 0) surfaces have been investigated by means of density functional theory calculations and cluster models and periodic slabs. According to the cluster models, the optimized results indicate that the basis set of C and O atoms has a distinct effect on the adsorption energy, but an indistinct one on the equilibrium geometry. For the CO₂/Cu(hkl) adsorption systems studied here, the final structure of adsorbed CO₂ is near linear and the preferred modes for the adsorption of CO₂ onto the Cu(1 1 1), Cu(1 0 0), and Cu(1 1 0) surfaces are the side-on adsorption at the cross bridge site with an adsorption energy of 13.06 kJ/mol, the side-on adsorption at the short bridge site (13.54 kJ/mol), and the end-on adsorption on the on-top site with C–O bonds located along the short bridge site (26.01 kJ/mol), respectively. However, the calculated adsorption energies from periodic slabs are lower as compared to the experimental data as well as the cluster model data, indicating that the periodic slab approach of generalized gradient approximation in the density function theory may be not suitable to obtain quantitative information on the interaction of CO₂ with Cu(hkl) surfaces.     

二氯和邻菲罗啉二酮的镍(Ⅱ)、铜(Ⅱ)、锌(Ⅱ)配合物的合成与表征

以ＭＣｌ２和配体Ｌ（Ｌ＝１，１０－菲罗啉－５，６－二酮）为原料，合成了标题配合物ＭＬＣｌ２，Ｍ＝ＮｉⅡ，ＣｕⅡ，ＺｎⅡ，并经元素分析、热谱、ＩＲ和摩尔电导表征．三者均为四配位的电中性配合物，热稳定性高于５００Ｋ，易溶于ＤＭＦ、ＤＭＳＯ和吡啶，可溶于乙腈和水．它们在ＤＭＦ中于３５０ｎｍ和３１５ｎｍ附近显示出强的Ｍ－Ｌ荷移跃迁     

Highly soluble and optically transparent poly (ether imide)s based on 2,6‐ or 2,7‐bis(3,4‐dicarboxyphenoxy)naphthalene dianhydride and aromatic bis(ether amine)s bearing trifluoromethyl groups

Two series of novel fluorinated poly(ether imide)s (coded IIIA and IIIB ) were prepared from 2,6‐bis(3,4‐dicarboxyphenoxy)naphthalene dianhydride and 2,7‐bis(3,4‐dicarboxyphenoxy)naphthalene dianhydride, respectively, with various trifluoromethyl‐substituted aromatic bis(ether amine)s by a standard two‐step process with thermal or chemical imidization of the poly(amic acid) precursors. These fluorinated poly(ether imide)s showed good solubility in many organic solvents and could be solution‐cast into transparent, flexible, and tough films. These films were nearly colorless, with an ultraviolet–visible absorption edge of 364–386 nm. They also showed good thermal stability with glass‐transition temperatures of 221–298 °C, 10% weight loss temperatures in excess of 489 °C, and char yields at 800 °C in nitrogen greater than 50%. The 2,7‐substituted IIIB series also showed better solubility and higher transparency than the isomeric 2,6‐substituted IIIA series. In comparison with nonfluorinated poly (ether imide)s, the fluorinated IIIA and IIIB series showed better solubility, higher transparency, and lower dielectric constants and water absorption. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5909–5922, 2006     

Magnetic properties of nickel-zinc ferrites synthesized from liquid solutions produced in chemical and electrochemical processing of metals

Nickel-zinc ferrite was prepared by coprecipitation from liquid waste formed in chemical and electrochemical processing of metals.     

Rational Homotopy Theory and Nonnegative Curvature

in this note, we answer positively a question by Belegradek and Kapovitch about the relation between rational homotopy theory and a problem in Riemannian geometry which asks that total spaces of which vector bundles over compact non-negative curved manifolds admit （complete） metrics with non-negative curvature.     

关于非球面制造技术的看法

列举了现代诸高科技领域对非球面光学系统的需求实例，如短波光学，空间光学，红外光学，微电子技术等。然后比较讨论了刀口阴影法与数字干涉检验的优缺点。在非球面修磨方法方面，首先肯定了计算机辅助加工是发展的方向，指出其主要优点在于“失误”造成的反复率大大降低。最后对非球面技术提出了总的看法，并对检测方法和修磨方法提出了几个研究课题。     

无机螺旋体超分子配合物的组装、应用和结构转化研究进展

简述了近年来报道的具有新颖结构和性能的无机螺旋体超分子配合物的组装、应用和结构转化方面的最新进展,并展望了无机螺旋体的发展前景及其开发应用潜力。