Investigations of the dissociation behavior and interfacial adsorption characteristics of polyelectrolytes from poly(acrylamido‐2‐methyl‐1‐propane sulfonic acid) with an octadecyl side chain

Water‐soluble polymeric amphiphiles derived from acrylamido‐2‐methyl‐1‐propane sulfonic acid (AMPS) and octadecyl monomers in which the linker groups vary among acryloyl [octadecyl methacrylate (ODMAc)], maleate [octadecyl maleate ester (ODME)], and maleamic acid [octadecyl maleamic acid (ODMA)] have been synthesized. The dissociation behavior in water from potentiometric titration suggests that these polymers show resistance to neutralization. This might arise from coil structures, which effect the destabilization of sulfonate ions because of a proximity effect. The effect of the ? COOH group in modifying the dissociation behavior in the copolymers AMPS–ODME and AMPS–ODMA is indicated. The ratio of the intensities of the third vibronic peak (I₃) to the first vibronic peak (I₁) of the fluoroprobe pyrene in the presence of polymer solutions shows negligible changes as a function of pH, and this suggests the retention of micropolarity. The high I₃/I₁ value observed in the presence of the ODMAc polymer suggests intermolecular association. The reduction in the reduced viscosity with the concentration of the polymers suggests the polyelectrolyte behavior of all the copolymers. The progressive decrease in the reduced viscosity from 120 to 95 mL/g when the degree of ionization increases from 0.5 to 1 for the ODME polymer suggests changes in the solution structure. AMPS–ODMA and AMPS–ODME polymers exhibit significant adsorption at the interface and exhibit equilibrium surface tensions of 58.8 and 56.3 mN/m, respectively. The lower surface activity and higher reduced viscosity of ODMAc polymer solutions further support the formation of intermolecular associated or network structures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 314–324, 2006     

Exponential stability for markovian jumping stochastic BAM neural networks with mode‐dependent probabilistic time‐varying delays and impulse control

In this article, an exponential stability analysis of Markovian jumping stochastic bidirectional associative memory (BAM) neural networks with mode‐dependent probabilistic time‐varying delays and impulsive control is investigated. By establishment of a stochastic variable with Bernoulli distribution, the information of probabilistic time‐varying delay is considered and transformed into one with deterministic time‐varying delay and stochastic parameters. By fully taking the inherent characteristic of such kind of stochastic BAM neural networks into account, a novel Lyapunov‐Krasovskii functional is constructed with as many as possible positive definite matrices which depends on the system mode and a triple‐integral term is introduced for deriving the delay‐dependent stability conditions. Furthermore, mode‐dependent mean square exponential stability criteria are derived by constructing a new Lyapunov‐Krasovskii functional with modes in the integral terms and using some stochastic analysis techniques. The criteria are formulated in terms of a set of linear matrix inequalities, which can be checked efficiently by use of some standard numerical packages. Finally, numerical examples and its simulations are given to demonstrate the usefulness and effectiveness of the proposed results. © 2014 Wiley Periodicals, Inc. Complexity 20: 39–65, 2015     

Micromanipulation of Mechanically Compliant Organic Single‐Crystal Optical Microwaveguides

Flexible organic single crystals are evolving as new materials for optical waveguides that can be used for transfer of information in organic optoelectronic microcircuits. Integration in microelectronics of such crystalline waveguides requires downsizing and precise spatial control over their shape and size at the microscale, however that currently is not possible due to difficulties with manipulation of these small, brittle objects that are prone to cracking and disintegration. Here we demonstrate that atomic force microscopy (AFM) can be used to reshape, resize and relocate single‐crystal microwaveguides in order to attain spatial control over their light output. Using an AFM cantilever tip, mechanically compliant acicular microcrystals of three N‐benzylideneanilines were bent to an arbitrary angle, sliced out from a bundle into individual crystals, cut into shorter crystals of arbitrary length, and moved across and above a solid surface. When excited by using laser light, such bent microcrystals act as active optical microwaveguides that transduce their fluorescence, with the total intensity of transduced light being dependent on the optical path length. This micromanipulation of the crystal waveguides using AFM is non‐invasive, and after bending their emissive spectral output remains unaltered. The approach reported here effectively overcomes the difficulties that are commonly encountered with reshaping and positioning of small delicate objects (the “thick fingers” problem), and can be applied to mechanically reconfigure organic optical waveguides in order to attain spatial control over their output in two and three dimensions in optical microcircuits.     

Highly efficient one-pot synthesis of α-aminophosphonates using nanoporous AlSBA-15 catalyst in a three-component system

Research on Chemical Intermediates - Nanoporous AlSBA-15 catalysts with different nSi/nAl ratios (41, 129, and 210) were synthesized using a hydrothermal method. These catalysts were characterized...     

Effect of piperidones on hydrogen permeation and corrosion inhibition of mild steel in acidic solutions

The influence of 3-methyl-2,6-diphenyl piperidin-4-one (MDPO) and 2-phenyl decahydroquinoline-4-one (PDQO) synthesised in the laboratory on hydrogen permeation and corrosion inhibition of mild steel in 1N H₂SO₄ has been studied using weight loss and various electrochemical AC and DC corrosion-monitoring techniques. Both the compounds inhibit the corrosion of mild steel in H₂SO₄. Potentiodynamic polarisation studies clearly reveal that they behave predominantly as cathodic inhibitors. The extent of decrease in hydrogen permeation current through steel surfaces has been studied by the hydrogen electropermeation technique. Double layer capacitance (C _dl ) and charge transfer resistance (R _t ) values are derived from Nyquist plots obtained from AC impedance studies. The adsorption of these compounds on mild steel surfaces from H₂SO₄ obeys Temkin’s adsorption isotherm.     

Interfacial adsorption characteristics of ionic polymeric amphiphiles with comb‐like structures: Effect of dodecyl and poly(ethylene oxide) side chains

Two sets of terpolymers, polymer A and polymer B consisting of almost same level of 2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid (AMPS) component at 0.635 ± 0.005 m and varying dodecyl methacrylate (DoDMAc) and monomethoxy poly(ethylene glycol) acrylate (PEGAc) components have been designed. Polymer A, consisting of less C₁₂ component, has been shown to promote intermolecular aggregated structures wherein C₁₂ domains exhibit compact packing characteristics. It is demonstrated that in polymer B, AMPS segments are predominantly present as ionic clusters contributing to a high pKa at about 9.50 for a low α of 0.20. From the results of interfacial adsorption estimations at air/solution and water/hexane interface, it is shown that open coil structures provided under high pH (>9.0) conditions promote efficiency of adsorption. This is shown from higher surface excess concentration (Γ) and lower interfacial area (a) estimated using Gibbs adsorption isotherm equation. For example, at water/hexane interface, polymer A exhibits Γ of 1.20 × 10^?3 moles/1000 m² at pH 3.2 and 1.97 × 10^?3 moles/1000 m² at pH 10.0. Significantly, in case of polymer B consisting of ionic clusters of AMPS, adsorption at the liquid/liquid interface is more efficient in comparison to polymer A at all pH. © 2008 Wiley Periodicals, Inc. JPolym Sci Part A: Polym Chem 46: 3257–3271, 2008     

Shape and size transformation of gold nanorods (GNRs) via oxidation process: A reverse growth mechanism

The anisotropic shape transformation of gold nanorods (GNRs) with H₂O₂ was observed in the presence of “cethyl trimethylammonium bromide” (CTAB). The adequate oxidative dissolution of GNR is provided by the following autocatalytic scheme with H₂O₂: Au⁰ → Au⁺, Au⁰ + Auⁿ⁺ → 2Au³⁺, n = 1 and 3. The shape transformation of the GNRs was investigated by UV-vis spectroscopy and transmission electron microscopy (TEM). As-synthesised GNRs exhibit transverse plasmon band (TPB) at 523 nm and longitudinal plasmon band (LPB) at 731 nm. Upon H₂O₂ oxidation, the LPB showed a systematic hypsochromic (blue) shift, while TPB stays at ca. 523 nm. In addition, a new emerging peak observed at ca. 390 nm due to Au(III)-CTAB complex formation during the oxidation. TEM analysis of as-synthesised GNRs with H₂O₂ confirmed the shape transformation to spherical particles with 10 nm size in 2 h, whereas centrifuged nanorod solution showed no changes in the aspect ratio under the same condition. Au³⁺ ions produced from oxidation, complex with excess free CTAB and approach the nanorods preferentially at the end, leading to spatially directed oxidation. This work provides some information to the crystal stability and the growth mechanism of GNRs, as both growth and shortening reactions occur preferentially at the edge of single-crystalline GNRs, all directed by Br⁻ ions.     

Experiments to Explore the Mechanisms of Heat Transfer in Nanocrystalline Alumina/Water Nanofluid under Laminar and Turbulent Flow Conditions

Abstract

Heat transfer characteristics of water-based nanocrystalline alumina (Al₂O₃) nanofluids flowing through a uniformly heated tube under a fully developed laminar and turbulent flow regime is investigated experimentally in the present work to explore the heat transfer mechanism in nanofluids. In a laminar flow, the increase in Nusselt number was attributed to the thermophysical properties of the nanofluid. The movement of nanoparticles, along with the turbulent eddies in the turbulent core region and diffusion mechanism, such as thermophoresis, in the laminar sublayer are believed to be the reasons for enhanced heat transfer in turbulent region. The compatibility of Al₂O₃/water nanofluids was also examined by monitoring its color.     

Determination of crude fat in meat by supercritical fluid extraction: direct method: PVM 3:2000

Meat samples are prepared by passing meat through a food chopper, bowl cutter, or food processor, subsampling the meat, and mixing the meat with granular diatomaceous earth. No drying step is necessary. Supercritical CO2 is then used to extract crude fat (which is defined as the components of meat that are extractable with petroleum ether, without digestion of the sample). Extracted material is deposited on glass wool contained in collection vials. After removal of any residual moisture from the extracts, percent crude fat is determined by weight gain of the collection vial. This method has been peer-verified by 3 laboratories, for a wide variety of raw and processed meat products containing 6-28% crude fat. Samples were prepared at the submitting laboratory. Ground samples were split into 4 portions, packed in Whirlpack bags, and immediately frozen. Frozen samples were sent by overnight room temperature, and percent fat was determined (in triplicate), without further processing of the samples. Analysis of the samples was completed within 1 week of sample prepara. tion. On the basis of this study, it can be estimated that all repeatability and reproducibility values are <3.0. Mean accuracy of the direct gravimetric supercritical fluid extraction method for meat samples ranged from +0.22 to -1.41 when the method was compared with AOAC Method 960.39. Interferences are unlikely but would include any nonfat substance that is added to (processed) meat, is soluble in nonpolar solvents, and is present in a quantity that would alter results. This method is expected to perform equally well for all meats with fat content within the stated range of applicability.