The simulation of molecular and organic devices: a critical review and look at future developments

Molecular devices have lately attracted increased attention due to some appealing features such as their low production cost, flexibility in the substrate choice, possibility of large area deployment, and possibly higher integration capabilities. Starting from a series of results obtained from our groups, we critically review the state-of-the-art in the field of simulation of organic and molecular systems, by analyzing and comparing existing approaches, and looking at the open problems and possible solutions and future developments. PACS 72.80.Le     

Correlation between luminescent properties and structure organization in AlGaN/GaN superlattices annealed after erbium ion implantation

The evolution of the structure organization of MOCVD-grown AlGaN/GaN superlattices subjected to erbium ion implantation with an energy of 1 MeV and dose of 3 × 10¹⁵ cm^?2 and subsequent annealing is correlated with their photoluminescent properties. The structure organization is quantitatively estimated using parameter Δ (degree of violation of local symmetry), which is found via multifractal analysis of surface morphology patterns obtained with atomic force microscopy. It is shown that the implantation not only causes Ga segregation on the surface, but also changes the structure organization, which shows up in the finer grain structure compared with the starting one and disordering, as well as in an increase in Δ. As the annealing temperature rises from 700 to 800°C, Δ declines, indicating that the structure organization is improved, and the intensity of the dominating photoluminescence peak due to Er³⁺ ions (1.542 μm) grows. With a further increase in the annealing temperature to 1050°C, the structure organization degrades, domains get larger, voids 100–200 nm deep form, and the photoluminescence intensity drops. The formation of voids during high-temperature annealing is also substantiated by data for 230-keV proton scattering. It is thus established that the improvement of the superlattice structure organization activates erbium and causes the erbium-ion-related luminescence intensity to grow.     

Photoinitiated polymerization in bicontinuous microemulsions: Fluorescence monitoring

The photopolymerization of bicontinuous microemulsions was simultaneously monitored with differential scanning calorimetry and fluorescence. The kinetics and mechanism of the reaction were studied throughout the entire photopolymerization reaction. The role played by the surfactant in the kinetics and morphology was studied. The nature of the surfactant changed the autoacceleration process and final conversion. The behavior was explained as a result of the differences in the interfacial properties. Anionic cetyltrimethylammonium bromide (CTAB) gave rise to a more flexible interfacial film than anionic sodium dodecyl sulfate (SDS), resulting in competition between the intramolecular and intermolecular reactions in the former systems. As cyclization did not contribute to the increase in the degree of crosslinking, SDS photopolymerization gave solids with a more rigid microstructure. Fluorescence methodology was applied to monitor bicontinuous microemulsion polymerization and to reveal the microstructure and morphology development during photopolymerization. The microemulsion composition was designed to prepare nanoporous, crosslinked materials. Even though the nanostructure of the precursor microemulsions was not retained because of phase separation during polymerization, mesoporous solids were obtained. Their morphologies depended on the nature of the surfactant, and membranes with open cells were successfully prepared with CTAB, whereas more complex morphologies resulted with SDS. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5291–5303, 2006     

The phase diagram of a single polymer chain: New insights from a new simulation method

We present simulation results for the phase behavior of a single chain for a flexible lattice polymer model using the Wang-Landau sampling idea. Applying this new algorithm to the problem of the homopolymer collapse allows us to investigate not only the high temperature coil–globule transition but also an ensuing crystallization at lower temperature. Performing a finite size scaling analysis on the two transitions, we show that they coincide for our model in the thermodynamic limit corresponding to a direct collapse of the random coil into the crystal without intermediate coil–globule transition. As a consequence, also the many chain phase diagram of this model can be predicted to consist only of gas and crystal phase in the limit of infinite chain length. This behavior is in agreement with findings on the phase behavior of hard-sphere systems with a relatively short-ranged attractive square well. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2542–2555, 2006     

Differential AC-chip calorimeter for glass transition measurements in ultrathin films

A differential AC-chip calorimeter capable of measuring the step in heat capacity at the glass transition in nanometer-thin films is described. Because of the differential setup, pJ/K sensitivity is achieved. Heat capacity can be measured for sample masses below 1 ng in broad temperature range as needed for the study of the glass transition in nanometer-thin polymeric films. Relative accuracy is sufficient to investigate the changes in heat capacity as the step at the glass transition of polystyrene. The step is about 25% of the total heat capacity of polystyrene. The calorimeter allows for the frequency dependent measurement of complex heat capacity in the frequency range from 1 Hz to 1 kHz. The glass transition in thin polystyrene films (50–4 nm) was determined at well-defined experimental time scales. No thickness dependency of the glass transition temperature was observed within the error limits (±3 K)—neither at constant frequency (40 Hz) nor for the trace in the activation diagram (1 Hz–1 kHz). © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2996–3005, 2006     

Synthesis and properties of thermosetting polymers from a phosphorous‐containing fatty acid derivative

A new phosphorous‐containing fatty acid diepoxide was obtained from 10‐undecenoyl chloride and 10‐(2′,5′‐dihydroxyphenyl)‐9,10‐dihydro‐9‐oxa‐10‐phosphaphenanthrene‐10‐oxide and crosslinked with 4,4′‐diaminodiphenylmethane and bis(m‐aminophenyl)methylphosphine oxide. The properties of the thermosetting materials were evaluated by differential scanning calorimetry, dynamic mechanical thermal analysis, thermogravimetric analysis, and limiting oxygen index (LOI). Thermal and thermooxidative degradation was studied by gas chromatography/mass spectrometry, FTIR, ³¹P magic angle spinning NMR spectroscopy, and scanning electron microscopy. LOI values indicate good flame‐retardant properties that are related to the formation of a protective phosphorous‐rich layer that slowed down the degradation and prevented it from being total. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5630–5644, 2006     

Postmodification of poly(9‐alkyl‐9H‐carbazole‐2,7‐diyl)s as a route to new main‐chain‐functionalized carbazole polymers

The postmodification of poly[9‐(2‐hexyldecyl)‐9H‐carbazole‐2,7‐diyl] ( P1 ) upon its reaction with N‐bromosuccinimide affords exclusive and full bromination of the 3,6‐positions of the carbazole repeat units to yield poly[3,6‐dibromo‐9‐(2‐hexyldecyl)‐9H‐carbazole‐2,7‐diyl] ( P2 ). Brominated polymer P2 can be used as a precursor for further functionalization at the 3,6‐positions with the desired functional group to afford other useful polymers. Polymer P2 has hence been reacted with copper(I) cyanide to afford poly[3,6‐dicyano‐9‐(2‐hexyldecyl)‐9H‐carbazole‐2,7‐diyl] ( P3 ). Full substitution of the bromide groups with nitrile‐functional groups has been achieved. The preparation and structural characterization of polymers P2 and P3 are presented together with studies on their electronic conjugation and photoluminescence properties. Cyclic voltammetry studies on polymer P3 indicate that the new polymer is easier to reduce (n‐dope) but more difficult to oxidize than its unsubstituted counterpart ( P1 ) as a result of the introduction of the electron‐withdrawing nitrile‐functional groups at the 3,6‐positions on the carbazole repeat units on the polymer chains. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3336–3342, 2006     

Synthesis and characterization of polyimides derived from (3‐amino‐2,4,6‐trimethylphenyl)‐(3′‐aminophenyl)methanone and aromatic dianhydrides

A series of new polyimides were prepared via the polycondensation of (3‐amino‐2,4,6‐trimethylphenyl)‐(3′‐aminophenyl)methanone and aromatic dianhydrides, that is, 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA), 4,4′‐oxydiphthalic anhydride, 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride, and 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropane dianhydride. The structures of the polyimides were characterized by Fourier transform infrared and NMR measurements. The properties were evaluated by solubility tests, ultraviolet–visible analysis, differential scanning calorimetry, and thermogravimetric analysis. The two different meta‐position‐located amino groups with respect to the carbonyl bridge in the diamine monomer provided it with an unsymmetrical structure. This led to a restriction on the close packing of the resulting polymer chains and reduced interchain interactions, which contributed to the solubility increase. All the polyimides except that derived from BPDA had good solubility in strong aprotic solvents, such as N‐methyl‐2‐pyrrolidinone, N,N′‐dimethylacetamide, N,N‐dimethylformamide, and dimethyl sulfone, and in common organic solvents, such as cyclohexanone and chloroform. In addition, these polyimides exhibited high glass‐transition values and excellent thermal properties, with an initial thermal decomposition temperature above 470 °C and glass‐transition temperatures in the range of 280–320 °C. The polyimide films also exhibited good transparency in the visible‐light region, with transmittance higher than 80% at 450 nm and a cutoff wavelength lower than 370 nm. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1291–1298, 2006     

Synthesis and polymerization of a new nitrogen‐containing bis‐ortho‐diynylarene monomer

This study focuses on the preparation, characterization, and optical properties of new bis(3,4‐diphenylethynylphenyl)phenylamine. This is the first nitrogen‐containing bis‐ortho‐diynylarene (BODA) monomer having a nitrogen atom as the spacer group. BODA monomers are usually prepared from common bisphenols, thereby providing great synthetic versatility and the opportunity to develop a wide array of novel polyarylene thermosets by varying the aromatic spacer group. The new bis(3,4‐bisphenylethynylphenyl)phenylamine was synthesized in five steps. This compound emits an intense blue color (λ = 438 nm) upon irradiation by UV light and may be suitable for use as an emitting layer in electroluminescent devices. Bis‐(3,4‐bisphenylethynylphenyl)phenylamine and its polymer have photoluminescence quantum yields 34 and 38%, respectively, and long excited‐state lifetimes of 3.2 and 3.6 ns, respectively. The structure of the monomer and its polymer were characterized using spectroscopic techniques including Ultraviolet–visible Spectrophotometer, Photoluminescence Spectrophotometer, Fourier Transform infrared spectroscopy, and Gel Permeation Chromatography. The polymerizations were studied by Differential Scanning Calorimeter. The amount of weight loss and the thermostability of the nitrogen‐containing polymer were determined from thermogravimetric analysis. The electrical conductivity of neat HCl‐doped BODA‐derived polymer film was measured according to the standard four‐point probe technique. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6988–6996, 2006