The composition analysis of YBa2Cu3O7-δ or PrBa2Cu3O7-δ thin films and (YBa2Cu3O7-δ/PrBa2Cu3O7-δ)n heterostructures prepared by CVD

Some YBa₂Cu₃O_7-δ films and heterostructures prepared by Chemical Vapor Deposition (CVD) were analyzed in our laboratories by EPMA-EDX or WDX, RBS, SNMS and AES. It was found that in some cases the results of composition analysis can significantly deviate from each other. At least two main reasons for these deviations exist: the different lateral resolution and the application of different reference samples for the calibration. Received: 3 June 1996 / Revised: 14 October 1996 / Accepted: 16 October 1996     

Thermal decomposition of the composite hydrotalcites of iowaite and woodallite

The thermal stability and thermal decomposition pathways for synthesized composite iowaite/woodallite have been determined using thermogravimetry analysis in conjunction with evolved gas mass spectrometry. Dehydration of the hydrotalcites occurred over a range of 56–70°C. The first dehydroxylation step occurred at around 255°C and, with the substitution of more iron(III) for chromium(III) this temperature increased to an upper limit of 312°C. This trend was observed throughout all decomposition steps. The release of carbonate ions as carbon dioxide gas initialised at just above 300°C and was always accompanied by loss of hydroxyl units as water molecules. The initial loss of the anion in this case the chloride ion was consistently observed to occur at about 450°C with final traces evolved at 535 to 780°C depending of the Fe:Cr ratio and was detected as HCl (m/z=36). Thus for this to occur, hydroxyl units must have been retained in the structure at temperatures upwards of 750°C. Experimentally it was found difficult to keep CO₂ from reacting with the compounds and in this way the synthesized iowaite-woodallite series somewhat resembled the natural minerals.     

Laser-induced charge transfer in the LiH3+ quasi-molecule

The laser-induced charge-transfer cross section for Li³⁺ + H collisions is calculated using the perturbation approach of Copelang and Tang, and is compared to the collision-induced cross section. The validity of perturbation theory and the use of simple criteria based on the Landau-Zener formula to extend the usefulness of the theory are examined.     

Importance de la conformation des complexes XC6H5Cr(CO)3 pour la regiosélectivité d'additions nucleophiles sur le cycle aromatique

The site of preferred nucleophilic attack on XC₆H₅Cr(CO)₃ complexes is more influenced by the conformation of the Cr(CO)₃ group than by the nature of X substituent. This is supported both by experimental and theoretical results.     

Fe(CO)5 thin films adsorbed on Au(111) and on self-assembled organic monolayers: I. Structure

The adsorption of Fe(CO)(5) onto Au(111)/mica and C(4), C(8), C(12), and C(16) SAMs/Au(111)/mica surfaces has been studied using infrared spectroscopy to elucidate the coverage-dependent structures of these films and the intermolecular couplings that determine the form of the spectra. For all substrates, the first layer is composed of molecules physisorbed with one axial and two equatorial carbonyl groups directed toward the substrate; subsequent layers are preferentially oriented with the C(3) molecular axis aligned perpendicular to the substrate (i.e., one axial carbonyl group directed toward the substrate). The axial vibrational band systematically shifts to higher frequencies with increasing surface coverage because of the effects of intermolecular coupling of the quasiparallel transition dipole moments. The strong effects of dipolar coupling are also witnessed by the trends of the band positions when the distance to the image plane is systematically varied using highly organized self-assembled organic substrates; no band shifts are observed when dilute Fe(CO)(5) is embedded in Xe matrixes under identical experimental conditions. The as-deposited films are structurally stable below 125 K on Au(111)/mica surfaces and below 100 K on the organic self-assembled monolayers. The instability of the films above these temperatures demonstrates that the as-adsorbed films do not form thermodynamically well-defined phases but are structurally metastable. The results presented herein and in the companion paper provide a consistent framework to interpret the spectroscopy of these systems that resolves outstanding issues concerning these films and provides a structural model that explains the dynamic properties of these films during exposure to low-energy electron beams.     

Efficient synthesis of an imidazole-substituted delta-amino acid by the integration of chiral technologies

Two methods to produce (2S)-5-amino-2-(1-n-propyl-1H-imidazol-4-ylmethyl)-pentanoic acid were investigated. Diastereoisomeric salt resolution, using the quinidine salt, gave the desired intermediate in 98% ee and 33% yield. Asymmetric hydrogenation of various substrates gave high conversions, with up to 83% ee. Integration of these two approaches via asymmetric hydrogenation of a quinidine salt substrate followed by crystallization provided the desired intermediate in 94% ee and 76% yield.     

Mesoporous micelle templated silica with incorporated C<Subscript>8</Subscript> and C<Subscript>18</Subscript> phase

Mesoporous silica material of MCM-41 type was synthesized by co-condensation of highly concentrated octyltriethoxysilane (OTEOS), octadecyltriethoxysilane (ODTEOS) and tetraethoxysilane (TEOS). The obtained hybrid materials were characterized using XRD, TG-DSC and low temperature adsorption/desorption of nitrogen. It was shown that the applied method of synthesis allows to obtain silica of MCM-41 type with a high degree of hydrocarbon saturation.     

Preparation of HPMC–EA–DMAEMA nanosized latex

Nanosized copolymer latex of hydroxypropylmethylcellulose (HPMC) grafted with ethyl acrylate (EA) and dimethylaminoethyl methacrylate (DMAEMA) has been prepared by acidifying submicron-sized latex particles synthesized by soap-free emulsion graft copolymerization using potassium persulfate (KPS) as initiator. The effects on the diameter of the latex particles of different conditions, for example concentration of DMAEMA, amount of HPMC, and ratio of HCl to DMAEMA for acidification, were investigated. It was found that increasing the mole ratio of HCl to DMAEMA to 1.0 and increasing the DMAEMA content both resulted in a decrease in particle diameter, whereas increasing the amount of HPMC resulted in larger particle sizes. Measurement by dynamic light scattering (DLS) revealed the diameter of the latex particles was >200 nm before acidification and <100 nm after acidification. Evidence of grafting was obtained by use of Fourier transform infrared (FTIR) spectroscopy. Transmission electron microscopy (TEM) was used to characterize the morphology of the copolymer particles before and after acidification.     

Influence of thermal and thermo-mechanical treatment

Two lipids with similar melting ranges but of different composition were analyzed using differential scanning calorimetry and X-ray diffraction. The lipids were processed via extrusion or were tempered at different temperatures; they were analyzed directly after extrusion and after storage at 40°C. Precirol ATO 5® showed high sensitivity to storage time and varied temperature exposure. Extrusion showed only marginal influences on the solid state. Melting peaks were narrower and shifted to higher temperatures in comparison to the untreated powder. Dynasan 114® was more robust, changes in the solid state could only be shown for samples treated above the melting range. Thus, Dynasan 114® is more appropriate for solid lipid extrusion of pharmaceutical products.