红外中带滤光片的结构、带宽估算及调整

中波红外波段在航天、气象、遥感等领域有着重要的应用，为了提高信噪比，系统中经常使用高质量的红外中带滤光片。相对带宽是红外中带滤光片重要的指标，主要取决于光学薄膜的膜系结构和具体设计。首先给出双截止组合型、F-P型、多半波型等几种膜系结构，归纳了相对带宽估算公式。同时从实用性出发，对一些具体膜系结构进行了相对带宽估算和综合分析，结果表明多半波结构最为可行。针对多半波结构，提出了间隔层膜料和光学厚度的选择、采用等效膜、调整膜层折射率等相对带宽调整的方法。最后，利用上述相对带宽调整方法对红外中带滤光片进行了设计，给出了实际镀制结果，滤光片相对带宽指标满足设计要求。     

理性、有序地建设探究实验室

建设探究实验室是提高学生对学习、学科兴趣的重要举措.本文提出了一套探究实验室评价方案以期对实验室的建设和发展有所帮助.总体评价和导向性评价基于对一个个实验就一些指标进行评估以及其后的统计.我们还对一些深层次的要求和指标进行了探讨.     

Ag偏离化学计量比Ag1-xPb18SbTe20材料的热电传输性能

采用熔融-淬火-放电等离子体烧结制备了Ag偏离化学计量比Ag1-xPb18SbTe20(x=0,0.25,0.50,0.75)样品,研究了Ag含量对样品热电传输性能的影响.结果表明,随Ag含量降低,样品中出现少量第二相Sb2Te3,样品载流子浓度增加到5×1018cm-3后不再增加.样品载流子迁移率随Ag含量降低先降低后增加,随着温度增加,载流子散射机理由电离杂质散射转变为声学波散射.随Ag含量降低,样品电导率增加而Seebeck系数降低,热导率增加.     

冷冻靶技术研究

在低温物理研究方面，完成高压充气冷冻装置设计工作。设计指标为：充气压力100MPa，增压速率0．5-25MPa／h(可控)，靶丸充注时间6-300h，最小冷却速率1K／min，压力控制精度0．25MPa。系统冷源采用功率0．5-1W、最低温度4．2K的低温制冷机冷却。这种系统使用灵活、方便，只要有电源就可以开展正常的实验，实验时间不受限制，制冷机运行时有微小的振动。     

采用空心阴极放电等离子体化学气相沉积方法制备a-CH薄膜

 研究了不同衬底-阴极距离、直流电压和H₂流量对a-CH薄膜沉积速率的影响。结果表明：衬底-阴极距离必须大于0.5cm，随着该距离的增加，薄膜的沉积速率减少；直流电压达550V时沉积速率最大；随着H2含量的增加，CH₄含量相对减少，沉积速率随之降低。用AFM观察了以该方法制得的448.4nm CH薄膜的表面形貌，表面粗糙度约为10nm。最后测出了不同条件下CH薄膜的UV-VIS谱，由此可以计算得到薄膜的禁带宽度及折射率。     

低热固相反应的反应机理研究(1)--冷融熔机理和冷溶熔机理的模型

本文提出了低热固相反应的冷融熔机理和冷溶熔机理,其中冷融熔机理主要针对于不含结晶水的反应体系,冷溶熔机理主要针对于含结晶水的反应体系,并对低热固相反应动力学提出冷融熔/冷溶熔、扩散、反应、成核、生长的五步机理.两种机理都避开了分子在固相晶格中的扩散,从而对低热固相反应的扩散问题进行了有效的解释,并给出了低热固相反应的热力学和动力学判据.     

Cu（Ⅱ）—A沸石的表征

用ESR表征了几种Cu(Ⅱ)-A沸石中Cu~(2+)离子物种,发现在铜含量较高(5.20wt%)的样品中,偶极-偶合的Cu~(2+)离子对占压倒优势,而孤立的Cu~(2+)离子则很少.样品还原后的ESR结果表明,偶极-偶合的Cu~(2+)离子对至少存在着两种不同类型的物种.结合ESR、XPS和XRD方法,研究了Cu(Ⅱ)-A沸石中共存阳离了Mn~(2+)的效应,并讨论了Cu~(2+)和Mn~(2+)两种离子间的氧化还原反应.     

椭圆截面曲线管道内二次流动的Galerkin解

推导了任意空间曲线直角坐标系内的张量流体力学方程．采用Galerkin方法和计算机符号运算技术求解了椭圆截面螺旋管道（电括弯管、扭管）内的二次流动．计算结果表明了Galerkin方法的适用和有效性，克服了振动法的小参数局限．对所得结果的分析揭示了椭圆截面螺旋管道内流动的特性，给出了k,r和Re较大情况的研究结论．     

Sputtering pressure influence on growth morphology,surface roughness,and electrical resistivity for strong anisotropy beryllium film

The strong anisotropy beryllium （Be） films are fabricated at different sputtering pressures by direct current magnetron sputtering. With the increase of pressure, the deposition rate of Be film first increases, and when the pressure exceeds 0.8 Pa, it gradually descends. The X-ray diffraction analysis indicates that Be film is of α-Be phase, its surface always reveals the （101） crystal plane possessing the low surface energy. As for the growth morphology of Be film, the surface is mainly characterized by the fibrous grains, while the cross section shows a transition from a columnar grain to a mixed grain consisting of a cone-shaped grain and a columnar grain as the sputtering pressure increases. The large grain fraction decays exponentially from 75.0% to 59.3% with the increase of sputtering pressure p, which can improve the grain size uniformity. The surface roughness increases due to the insufficient atom diffusion, which is comparable to its decrease due to the etching effect at p 〈 0.8 Pa, while it increases drastically at p 〉 0.8 Pa, and this increase is dominated by the atom diffusion. The electrical resistivity values of Be films range from 1.7 μΩ m to 2.7 μΩ m in the range 0.4 Pa-1.2 Pa, which is 50 times larger than the bulk resistivity.     

Phase mismatching analysis of third-harmonic generation in BBO crystal

<正>Phase mismatching for third-harmonic generation(THG) in barium metaborate(BBO) crystal is investigated in detail.Upon using BBO crystal in the TypeⅠ(oo→e) scheme,in the two independent planes (principal section of the crystal and the plane normal to principal section),when the input second-harmonic beam deviates from the expected direction,phase mismatching occurs and the angle deviation produces different effects on the conversion efficiency.We numerically simulate these two cases of phase mismatching and identify the relation between the conversion efficiency and the deviation angle in the air.The computational results indicate that the phase matching tolerance in the principal section is 0.2°(in the air),while the phase matching tolerance in the plane normal to principal section is 4.5°(in the air).After conducting a lab experiment,the results agree perfectly with the computational results,indicating that the deviation angle in the principal section has a greater effect on the conversion efficiency.