Micromagnetic analysis of transition noise for high-density perpendicular recording

In this paper, specific issues related to high-density perpendicular magnetic recording processes, such as transition noise properties and cross-track correlation lengths, were investigated with the help of micromagnetic analysis. The effects of media parameters were taken into consideration, including intergranular exchange coupling, and exchange distribution, irregular grain shapes, magnetization saturation distribution, and anisotropy distribution. The micromagnetic simulation results showed that the effect of anisotropy distribution on transition noise is more significant than magnetization saturation distribution, and it is crucial to reduce this effect to achieve a high signal-to-noise ratio. Additionally, a new method to further estimate the partial erasure threshold was proposed to approximate the partial erasure effects, and the relation between the microtrack jitter and total track jitter was investigated.     

Mössbauer effect study of the decagonal quasicrystal Al65Co15Cu20

The ⁵⁷Fe Mössbauer effect study at 5.0 K and in an external magnetic field of 9.0 T on a high-quality stable decagonal quasicrystal Al₆₅Co₁₅Cu_19.9Fe_0.1 is presented. It is shown that the iron atoms are located in two distinct classes of sites. The values of the principal component of the electric field gradient tensor and the asymmetry parameter at these sites are, respectively, ?1.90(10)?×?10²¹ V/m², 0.97(15) and ?3.95(12)?×?10²¹ V/m², 0.00(17).     

Structure transition of single-texture CoSi2 nanolayer grown by refractory-interlayer-mediated epitaxy method

In this investigation, the crystalline structure of a nanometric CoSi₂ layer, formed in heat treated Co/W_xTa_(1−x)/Si(1 0 0) systems, has been studied by XRD analysis. Careful measurements of the diffraction intensities revealed that temporary formation of a metastable diamond cubic structure of CoSi₂ phase, rather than its usual CaF₂ structure, was occurred. It has been shown that formation of this metastable structure depends on the kind of the applied interlayer in addition to the annealing temperature. Among the studied systems with x = 0, 0.25, 0.5, 0.75 and 1, the second and the last systems resulted in growing a (1 0 0) single-texture CoSi₂ layer with the preferred usual CaF₂ structure, a strained lattice parameter, and the best thermal stability (900-1000 °C).     

Advances in constant-velocity Mössbauer instrumentation

A prototype of a programmable constant-velocity scaler is presented. This instrument allows the acquisition of partial Mössbauer spectra in selected energy regions using standard drivers and transducers. It can be fully operated by a remote application, thus data acquisition can be automated. The instrument consists of a programmable counter and a constant-velocity reference. The reference waveform generator is amplitude modulated with 13-bit resolution, and is programmable in a wide range of frequencies and waveforms in order to optimize the performance of the transducer. The counter is compatible with most standard SCA, and is configured as a rate-meter that provides counts per selectable time slice at the programmed velocity. As a demonstration of the instrument applications, a partial Mössbauer spectrum of a natural iron foil was taken. Only positive energies were studied in 512 channels, accumulating 20 s per channel. A line width of 0.20 mm/s was achieved, performing with an efficiency of 80%.     

Generation of red light at 660 nm by frequency doubling a Nd:YAG laser with periodically-poled stoichiometric LiTaO<Subscript>3</Subscript>

High power red light was generated from a periodically-poled stoichiometric LiTaO₃ (PPSLT) by single-pass frequency doubling of a diode-side-pumped, Q-switched Nd:YAG laser at 1319 nm. An average power of 2.4 W of the 660 nm red light was obtained at the fundamental power of ∼5.4 W with the conversion efficiency up to 44.4% and with low fluctuation down to 2%. The high efficiency and stability at the red output indicate that it is a practical method to construct a reliable compact red laser. PACS 42.70.Mp; 42.79.Nv; 42.55.Xi     

Structure and mechanical properties of Al/AlN multilayer with different AlN layer thickness

Nanometer scale Al/AlN multilayers have been prepared by dc magnetron sputtering technique with a columnar target. A set of Al/AlN multilayers with the Al layer thickness of 2.9 nm and the AlN layer thickness variation from 1.13 to 6.81 nm were determined. Low angle X-ray diffraction (LAXRD) was used to analyze the layered structure of multilayers. The phase structure of the coatings was investigated with grazing angle XRD (GAXRD). Mechanical properties of these multilayers were thoroughly studied using a nanoindentation and ball-on-disk micro-tribometer. It was found that the multilayer hardness and reduced modulus showed no strong dependence on the AlN layer thickness. Al2.9 nm/AlN1.13 nm multilayer had more excellent tribological properties than single layers and other proportion multilayers with a lowest friction coefficient of 0.15. And the tribological properties of all the multilayers are superior to the AlN single layer.     

Thee + e −→¯nn cross section predicted remarkably larger than thee + e −→¯pp one

It is shown that all global analyses of nucleon electromagnetic form factor data predict the electron-positron annihilation into neutron-antineutron cross section (for which there are no data till now) to be in a finite energy region substantially larger than the electron-positron annihilation into the proton-antiproton one.Dedicated to the memory of M. Gmitro.     

Nontrivial Solutions for Resonant Hemivariational Inequalities

We study a resonant semilinear elliptic hemivariational inequality. Under some assumptions of strong resonance on the Clarke subdifferential of the superpotential, and using nonsmooth critical point theory, the existence of a nontrivial solution of the problem is shown. This paper has been partially supported by the State Committee for Scientific Research of Poland (KBN) under research grants no. 2 P03A 003 25 and no. 4 T07A 027 26.     

Interference of circularly polarized light: contrast and application in fabrication of three-dimensional periodic microstructures

The contrast of interference pattern formed by two circularly polarized waves and by a linearly polarized wave and a circularly polarized one is discussed. The results are compared with that by two linear beams. It shows that the use of circular light in holographic fabrication of three-dimensional periodic microstructures may remove the necessity of beam ratio and polarization optimization needed in the interference of three linear noncoplanar beams and improve the uniform contrast of resultant pattern simultaneously.