基于时频分布的盲信号分离方法研究长骨中的多模式导波信号

由于超声导波对长骨皮质骨的材料特性及厚度变化非常敏感,因此用导波评价长骨状况的研究已成为近年来的一个研究热点。在接收到的导波中,往往多种模式混叠在一起,使得进一步求取每种导波模式的群速度等与骨质状况密切相关的参数时遇到困难。本文采用基于时频分布的盲信号分离(TFBSS)方法对长骨中混叠的多模式进行分离,然后对分离后的单一导波模式求取群速度。研究结果表明TFBSS方法能够准确的分离出混叠的多模式导波,且实验测量的群速度与其理论值吻合。利用导波的群速度就可以得到长骨皮质骨的厚度,这对诊断其骨质状况具有重要意义。     

负偏压作用下染料敏化太阳电池界面及光电性能研究

太阳电池组件由于局部电压不匹配,其中部分电池可能较长时间工作在负偏压状态下,从而影响电池光电性能.借助拉曼光谱、电化学阻抗谱和入射单色光量子效率(IPCE)等测试手段,研究长期负偏压作用下染料敏化太阳电池光电性能的变化及其影响机理.拉曼光谱研究结果表明:电池在1000 h负偏压作用下,电解质中阳离子(Li⁺)会向光阳极(TiO₂电极)移动并嵌入TiO₂薄膜中;长期负偏压作用还会致使TiO₂/电解质界面阻抗增大和IPCE下降,导致电池开路电压升高和短路电流减小.通过加入苯并咪唑(BI)添加剂,经1000 h负偏压后电池的拉曼光谱实验表明,BI能在一定程度阻碍Li⁺的嵌入,电池具有较好的长期稳定性.不同负偏压下的老化实验进一步表明,通过加入添加剂能够使电池在长期负偏压下保持较好的稳定性. 关键词： 染料敏化 太阳电池 组件 负偏压     

Fast Si magic-angle-spinning NMR acquisitions by RAPT-CP Al → Si polarization transfer

Using enhancement of the ²⁷Al central-transition magnetization by applying RAPT prior to ²⁷Al → ²⁹Si cross-polarization, we demonstrate fast acquisition of ²⁹Si one-dimensional MAS and two-dimensional ²⁷Al–²⁹Si HETCOR spectra on a new sialon phase Ba₂Al₃Si₉N₁₃O₅.     

低孔隙度疏松铝的高压声速与冲击熔化

对含微孔洞疏松度m=1.04的疏松铝进行了冲击加载-卸载实验,利用DISAR(distance interferometer system for any reflector)测得了53至99 GPa五个冲击压力下疏松铝/LiF界面粒子速度波剖面,获得了各压力下的纵波声速和其中三个压力点的体波声速,确定出疏松铝的冲击熔化压力约为81 GPa,确定出高压下冲击熔化前的泊松比约为0.372.通过分析,微孔洞明显降低了冲击熔化压力,引起的非谐振效应明显,状态方程计算中考虑非谐效应,非谐因子l 关键词： 低孔隙度 疏松铝 声速 冲击熔化     

Investigation of the local structure variance of water molecules in laser-induced thermal desorption process

This paper presents the use of molecular dynamics simulation in the study of laser-induced thermal desorption (LITD) of water molecules adjacent to a laser-heated Au substrate. The local structure of the water molecules is investigated by considering the densities of the oxygen and hydrogen atoms, the average number of neighbors, n_NN, and the average number of H-bonds, n_HB. At an equilibrium temperature of 300 K, the simulation results show that three adsorption water layers are formed in the immediate vicinity of the Au surface, and that each four-fold hollow site on the uppermost Au(0 0 1) surface is occupied by a single water molecule. Following laser-induced heating of the Au substrate with a sub-picosecond laser pulse of 350 fs, the substrate temperature increases to 1000 K. This causes a gradual heating of the adjacent water film, which is accompanied by a decrease in the values of n_NN and n_HB. Hence, it can be concluded that an increase in the water film temperature destroys the hydrogen-bonding network throughout the water film. Although the maximum local temperature of the water film occurs in the region immediately adjacent to the Au substrate, it is determined that the attractive energy between the Au atoms and the water molecules in this region causes the water molecules to aggregate together to form three-dimensional water clusters. Furthermore, this energy prevents the hydrogen bonds in this region from breaking apart as violently as those within the phase explosion region. Finally, it is observed that the phase explosion phenomenon occurs in the region of the water film where the values of n_NN and n_HB are at a minimum.     

白光干涉偏振模耦合分布式光纤传感器分析

分布式光纤传感器能够测量沿光纤长度上连续分布的外界量。用保偏光纤作为传感光纤的分布式光纤传感器,被测外界量引起保偏光纤中传播的两正交偏振模的相互耦合。用迈克尔逊干涉仪两臂光程差来补偿两个偏振模的光程差的方法探测传感信号。为了设计白光干涉偏振模耦合分布式传感器,根据统计光学原理分析了传感器的互相干特性。在此基础上分析了传感器的空间分辨力、光纤耦合点分辨力、最大传感光纤长度。波长1310nm、谱宽36nm的超辐射发光二极管(SLD)作光源．用色散参量为600ps／km,拍长3mm的保偏光纤的分布传感器空间分辨力和光纤耦合点分辨力分别为6cm和3mm。     

基于时分复用技术的吸收光谱气体温度在线测量研究

可调谐半导体激光吸收光谱技术是一种具有高灵敏度、高选择性的非接触式气体在线测量技术。通过直接扫描多条H2O特征谱线并结合最小二乘算法实现对开放环境气体温度的在线测量。利用HITRAN光谱数据库详细讨论了边界效应对气体温度浓度测量的影响,计算结果表明,扫描多特征谱线并结合最小二乘算法可有效减小边界效应对开放环境气体温度测量的影响。实验中采用时分复用技术同时扫描了7 444.36,7 185.60,7 182.95和7 447.48cm-1四条H2O特征谱线,对管式炉573～973K范围内不同工况下的气体温度进行了测量。吸收光谱测量结果与热电偶信号的最大温差小于52.4K,温度测量最大相对误差为6.8%。     

Reflection chromaticity of cholesteric liquid crystals with sandwiched periodical isotropic defect layers

We study one-dimensional photonic crystals made of cholesteric liquid crystals with sandwiched isotropic defect layers. Based on the Berreman Fast 4 × 4 matrix method, the dispersion relation of one-dimensional photonic crystals is calculated and the corresponding reflection chromaticity is obtained. It is found that the color shift could be controlled by adjusting the thickness and refractive index of the isotropic defect layers. Compared with conventional structures, the reflection chromaticity of this structure is insensitive to the incident angle, if the thickness ratio of the cholesteric liquid crystals to that of the isotropic defect layers and the refractive index of periodical isotropic defect layers are properly set. Furthermore, the common forbidden bands for both left and right circular polarizations can be obtained, and we also take the wavelength-dependent refractive indices into consideration and obtain the reflected light chromaticity with the incident angle increasing. The proposed device can be used as a reflective color filter in the display industry.     

Conversion issues between microwave radiance and brightness temperature

Microwave radiances are usually converted into brightness temperatures for data assimilation and retrievals. The Rayleigh-Jeans approximation has been believed to be a good approximation for the conversion at low frequencies, but inaccurate at high frequencies. However, the simplified radiative transfer models under the Rayleigh-Jeans approximation (hereafter referred as BT-RTE) have been successfully applied in radiance simulations for frequencies below 183 GHz, which has somewhat puzzled the radiative transfer community. This paper clarifies the confusion. In addition, the conversion formula for the third and the fourth Stokes components are derived.Simulations for a polarized sensor, the Special Sensor Microwave Imager and Sounder, show that the BT-RTE is generally accurate. Results for a polarimetric sensor, WINDSAT, show that the third and the fourth Stokes radiances should be converted using the exact conversion formula given in this study rather than using a direct Planck function conversion.     

Immobilization of bovine serum albumin on TiO2 film via chemisorption of H3PO4 interface and effects on platelets adhesion

In the present study, bovine serum albumin (BSA) was successfully covalently immobilized on the surface of anatase TiO₂ film by a three-step method, i.e. application of H₃PO₄ chemisorption to increase surface -OH, which increases the amount of coupling 3-aminopropyl-triethoxylsilane (APTES), thus linking with BSA by imide bond using EDC/NHS/MES. There is no significant -OH group increase on rutile film when using the same method of phosphoric acid treatment, which suggest it is difficult for further chemical modification of the rutile film. After covalent immobilization of BSA on anatase film, an improved hemocompatibility of anti-platelet adhesion and aggregation in vitro could be recognized by LDH and SEM analysis. This study suggests BSA-immobilized anatase surface can serve as hemocompatibility material in vivo.