Mass spectrometric studies of benzoxazine resorcarenes

Eleven differently substituted 3,4-dihydro-2H-1,3-benzoxazine resorcarenes were studied by electrospray ionisation (ESI) and matrix-assisted laser desorption/ionisation (MALDI) mass spectrometry, using Fourier transform ion cyclotron resonance (FT-ICR) and time-of-flight (TOF) mass spectrometers, respectively. Under ESI conditions it was possible to transfer the intact resorcarenes from solution to the gas phase, yielding [M + H](+) and [M + 2H](+) ions as the main ions observed. Energy increase of the ions induced ready decomposition through successive eliminations of four CH(2)NR groups. Ion-molecule reactions showed that the ionising proton was situated somewhere inside the molecule and could not be reached with neutral reagent gases. In the host-guest complexation experiments, the benzoxazine resorcarenes studied turned out to be poor hosts for alkali metal and ammonium ions. In MALDI experiments, 2,5-dihydroxybenzoic acid proved to be the best matrix for these compounds. However, the intensity of the [M + H](+) ions was low for all compounds, and extensive fragmentation with consecutive elimination of CH(2)NR groups was observed.     

Configurational energetics in ice ih probed by compton scattering

Temperature-induced changes in the ground-state electron momentum density of polycrystalline ice Ih are studied with high accuracy by Compton scattering utilizing synchrotron radiation. A unique feasibility of the technique to provide direct experimental information on configurational enthalpies and heat capacities is demonstrated. The configurational enthalpy, obtained with an accuracy of 1.5 meV, evolves linearly with temperature above T=100 K. Consequently the configurational heat capacity is found to be constant, c{p}{config}=(0.44+/-0.11) J g{-1} K-1, in this temperature regime. Obtaining these quantities experimentally is fundamentally important for evaluating the accuracy of molecular-dynamics simulations schemes.     

Precision mass measurements of radioactive nuclei at JYFLTRAP

The Penning trap mass spectrometer JYFLTRAP was used to measure the atomic masses of radioactive nuclei with an uncertainty better than 10 keV. The atomic masses of the neutron-deficient nuclei around the line were measured to improve the understanding of the rp-process path and the SbSnTe cycle. Furthermore, the masses of the neutron-rich gallium ( ) to palladium ( ) nuclei have been measured. The physics impacts on the nuclear structure and the r-process paths are reviewed. A better understanding of the nuclear deformation is presented by studying the pairing energy around .     

Compatibilization of polyethylene/polyamide 6 blends with functionalized polyethylenes prepared with metallocene catalyst

Metallocene catalyst technology was utilized to prepare functionalized polyethylenes, which were used as compatibilizers in polyethylene/polyamide 6 (40/60) blends. Polymerization of ethylene with 10-undecen-1-ol, 10-undecenoic acid, or N-methyl-10-undecenylamine resulted in ethylene copolymers with a small amount (0.2–1.2 mol %) of functionalized side chains. The blends were prepared in a twin-screw midiextruder, and injection molded with a mini-injection molding machine. The effect of the new compatibilizers on morphology and mechanical and thermal properties was studied. Toughness as well as stiffness and strength increased significantly with an addition of 10 wt % compatibilizer. Morphology became much more uniform, and crystallization and melting behavior changed. The Molau test with FTIR analysis was used to determine that the desired reactions between the compatibilizer and polyamide had actually taken place. The results showed functionalized polyethylenes prepared with metallocene catalysts to act as effective compatibilizers in polyethylene/polyamide 6 blends. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3099–3108, 1999     

Ethylene polymerizations with novel tantalum(V) aminopyridinato complex/MAO systems

The use of two kinds of tantalum(V) aminopyridinato complexes, bis(2-benzylaminopyridinato)trichlorotantalum(V) and trichlorobis[2,6-di(phenylamino)pyridinato-N,N′]-tantalum(V), activated by methylaluminoxane was studied in polymerization of ethylene. The activities of these homogeneous catalyst systems are comparable to those of metallocenes. The weight-average molecular weights (M̄_w) of the produced polyethylenes are between 60 000 and 200 000 and M̄_w/M̄_n ≈ 2.     

Metallocene/methylaluminoxane‐catalyzed copolymerizations of oxygen‐functionalized long‐chain olefins with ethylene

Copolymerizations of ethylene with 10‐undecen‐1‐ol, 10‐undecenyl methyl ether, 10‐undecenyl trimethyl silyl ether, and 1‐undecene were performed with rac‐ethylene‐bis(1‐indenyl)zirconium dichloride as a catalyst and methylaluminoxane as a cocatalyst. All three oxygen‐functional comonomers copolymerized with ethylene, although the activity of the catalyst decreased considerably compared with the homopolymerization of ethylene. The conversions of the comonomers varied from 17 to 40%, depending on the amount of comonomer in the feed. Under the same conditions, the conversion of 1‐undecene was 50–75%. The incorporation (0.7–3.6 mol %, depending on the feed) and the effect on the activity of the catalyst were on the same level for all the functional comonomers, which indicates that trimethylsilyl or methyl groups do not act as effective protecting groups for oxygen atoms. According to NMR and Fourier transform infrared analyses, the final functional group in the copolymers of the trimethylsilyl ether comonomer was hydroxyl. In contrast, the methyl ether group remained untouched in the copolymer, which suggests that the formation of aluminum alkoxides via a reaction with a cocatalyst is not a prerequisite for comonomer incorporation. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1966–1971, 2000     

Fibre porosity development of dissolving pulp during mechanical and enzymatic processing

Dissolving grade pulps are used as raw material for manufacture of regenerated cellulose fibres and their use is constantly growing. Despite intensive research, there is still a need to develop cellulose dissolution-regeneration processes that would be economically viable, fulfil the pre-conditions of sustainability and would be able to meet the strict product quality requirements. The basis for creation of such a process is in deep understanding of the biomass structure and factors affecting the cellulose modification and dissolution. In this paper, the effects of the mechanical and enzymatic pre-treatments on the pore structure and alkaline solubility of dissolving grade pulp are discussed. Formation of micro- and macropores in the pulp fibres during mechanical shredding was found to correlate with the susceptibility of the fibres to enzymatic hydrolysis. The fibre porosity development during the processing was studied by a modified solute exclusion approach, which revealed differences between the effect of mild enzyme or acid hydrolysis on the pore structure of fibres. The dissolution of the modified fibres in NaOH/ZnO was evaluated and found to correlate with overall pore volume and accessible surface area analysed by the modified solute exclusion method.     

Calculation of valence electron momentum densities using the projector augmented-wave method

We present valence electron Compton profiles calculated within the density-functional theory using the all-electron full-potential projector augmented-wave method (PAW). Our results for covalent (Si), metallic (Li, Al) and hydrogen-bonded ((H₂O)₂) systems agree well with experiments and computational results obtained with other band-structure and basis-set schemes. The PAW basis set describes the high-momentum Fourier components of the valence wave functions accurately when compared with other basis set schemes and previous all-electron calculations.