Evaluation of indoor exposition to benzene, toluene, ethylbenzene, xylene, and styrene by passive sampling with a solid-phase microextraction device

A solid-phase microextraction (SPME) sampling method is developed to evaluate indoor exposure to benzene, toluene, ethylbenzene, xylene, and styrene with gas chromatography and flame ionization detection for quantitative analysis. An SPME holder with a 100-pm polydimethylsiloxane (PDMS) and 65-pm PDMS-divinylbenzene fiber coating is tested in different air relative humidity conditions. The method gives good resolution, shows a linear response, is repeatable, and presents high sensitivity. This method is compared with National Institute of Occupational Safety and Health (NIOSH) active sampling.     

Determination of trans-galactooligosaccharides in selected food products by ion-exchange chromatography: collaborative study

Eleven collaborating laboratories assayed 7 blind duplicate pairs of food and feed products for tans-galactooligosaccharides. The 7 laboratory sample pairs ranged from low (2%) to high levels (15%). Following the proposed method, the test samples were treated with beta-galactosidase and the released galactose was determined by ion-exchange chromatography. Repeatability standard deviation ranged from 2.9 to 11.6%; reproducibility standard deviation ranged from 4.6 to 11.6%.     

Phytochromes with noncovalently bound chromophores: the ability of apophytochromes to direct tetrapyrrole photoisomerization

Chromophore-apoprotein interactions were studied with recombinant apoproteins, oat phytochrome (phyA) and CphB of the cyanobacterium Calothrix PCC7601, which were both incubated with the bilin compounds biliverdin (BV) IXalpha, phycocyanobilin (PCB) and the 3'-methoxy derivative of PCB. Previously it was shown that CphB and its homolog in Calothrix, CphA, show strong sequence similarities with each other and with the phytochromes of higher and lower plants, despite the fact that CphB carries a leucine instead of a cysteine at the chromophore attachment position and thus holds the chromophore only noncovalently. CphA binds tetrapyrrole chromophores in a covalent, phytochrome-like manner. For both eyanobacterial phytochromes, red and far-red light-induced photochemistry has been reported. Thus, the role of the binding site of CphB in directing the photochemistry of noncovalently bound tetrapyrroles was analyzed in comparison with the apoprotein from phyA phytochrome. Both the aforementioned compounds, which were used as chromophores, are not able to form covalent bonds with a phytochrome-type apoprotein because of their chemical structure (vinyl group at position 3 or methoxy group at position 3'). The BV adducts of both apoproteins showed phytochrome-like photochemistry (formation of red and far-red-absorbing forms of phytochrome [P(r) and P(fr) forms]). However, incubation of the oat apophytochrome with BV primarily yields a 700 nm form from which the P(r)-P(fr) photochemistry can be initiated and to which the system relaxes in the dark after illumination. The results for CphB were compared with a CphB mutant where the chromophore-binding cysteine had been introduced, which, upon incubation with PCB, shows spectral properties nearly identical with its (covalently binding) CphA homolog. A comparison of the spectral properties (P(r) and P(fr) forms) of all the PCB- and BV-containing chromoproteins reveals that the binding site of the cyanobacterial apoprotein is better suited than the plant (oat) phytochrome to noncovalently incorporate the chromophore and to regulate its photochemistry. Our findings support the proposal that the recently identified phytochrome-like prokaryotic photoreceptors, which do not contain a covalently bound chromophore, may trigger a light-induced physiological response.     

Comparison of single extraction procedures,using either conventional shaking or microwave heating,and the Tessier sequential extraction method for the fractionation of heavy metals from environmental samples

The conventional four-step sequential extraction method and the EDTA and acetic acid single extraction procedures were applied to sewage sludge and sediment samples. The results obtained with these samples for Cu, Cr, Ni, Pb and Zn using the Tessier method were compared with those supplied by the two single extraction procedures employed. In addition, the Tessier method was also applied to a reference material, CRM 483, and these results were also compared with the certified EDTA and acetic acid values for this sample. As a result, good agreement was found between the metal contents released in the first three fractions of the Tessier method and those leached by the simpler single extraction procedures for the most of the elements studied. Subsequently, the conventional EDTA and acetic acid extraction methods were accelerated by means of microwave energy, in order to reduce the operating time. The extraction efficiency of the first three fractions of the Tessier method was compared with that obtained using the optimised microwave single extraction procedures and only in sewage sludge and CRM 483 samples were satisfactory results found for all the elements studied, except Cr and Pb. This means that the microwave single extraction procedures optimised in this work could be employed as screening methods to evaluate rapidly the easiest mobilizable heavy metals in these samples, although more samples should be analysed to determine their general applicability. The application of the accelerated single extraction procedures to a reference material, CRM 483, provided satisfactory results for all the elements studied, except for Cr in both methods and for Pb in the acetic acid extracts.     

Specific surface of two hydrated cements differing in strength

Specific surface, S, of CSH-gel particles of disordered layered structure, was studied by water sorption/retention in two cement pastes differing in strength, i.e. C-33 (weaker) and C-43 (stronger), w/c=0.4. Hydration time in liquid phase was t _h=1 and 6 months, followed by hydration in water vapour either on increasing stepwise the relative humidity, RH=0.5→0.95→1.0 (WS) or on its lowering in an inverse order (WR). Specific surface was estimated from evaporable (sorbed) water content, EV (110°C), assuming a bi- and three-molecular sorbed water layer at RH=0.5 or 0.95, respectively (WS). On WR it was three- and three- to four-molecular (50 to 75%), respectively, causing a hysteresis of sorption isotherm. At RH=0.5 the S increased with cement strength from 146 m² g^-1 (C-33, 1 m) to 166 m² g^-1 (C-43, 1 m) and with hydration time to 163 (C-33, 6 m) and to 204 m² g^-1 (C-43, 6 m). At RH=1.0 (and 0.95), higher S-value were measured but these differences were smaller: S amounted to 190-200 m² g^-1 in C-33 (1 and 6 m) and 198-210 m² g-1 in C-43 (1 and 6 m). Thus no collapse occurred on air drying of paste C-43 (6 m). This revised version was published online in July 2006 with corrections to the Cover Date.     

Synthesis and Characterization of Sol-Gel Cu-ZrO2 and Fe-ZrO2 Catalysts

Fe-ZrO₂ and Cu-ZrO₂ xerogels were prepared by a sol-gel method. The effect of the hydrolysis catalyst during the gelation step, namely H₂SO₄ or NH₄OH, on the properties of the resulting materials was investigated by XRD, BET, TGA/DTA, TPD of ammonia, FTIR, and TPR. Fe-ZrO₂ and Cu-ZrO₂ xerogels, with sulfuric acid introduced as the hydrolysis catalyst, mainly crystallyzed in the tetragonal phase and exhibited larger surface area and acid amount than those obtained with NH₄OH. Ammonia TPD shows that copper promoted sulfated zirconia is the most acidic material. TGA and FTIR reveal that under oxidizing conditions sulfated zirconia promoted with iron and copper retains more sulfate species than unpromoted sulfated zirconia. Regardless of the hydrolysis catalyst employed, copper promoted catalysts calcined at 600°C, contain a large fraction of copper oxide specieseasily reduced at low temperatures. These copper oxide species are believed to have different environment and interactions with the surface oxygen vacancies of the zirconia support. A FeO-like phase appears to be the most probable one after reduction of Fe-ZrO₂ catalysts prepared with NH₄OH as the hydrolysis catalyst. The formation of Fe° species may be hindered by the high dispersion and interaction of Fe²⁺ ions with the zirconia support. On the other hand, the reduction peaks of iron oxide and sulfate species exhibit a considerable overlap in the TPR profiles of sulfated Fe-ZrO₂ samples. Hence, the nature of the supported phase in the latter samples is rather uncertain.     

The Henderson Approximation and the Mass Action Law of Guldberg and Waage

Using contemporary accounts, we describe the scope of the Henderson approximation, and its relationship to the mass action law of Guldberg & Waage. The Henderson approximation, apparently written in logarithmic form by Hasselbalch, has the same form as the mass action law, but has a completely different meaning and a much more restricted range of applicability. The Guldberg-Waage law is the fundamental mass action relationship valid for all chemical equilibria, whereas the Henderson approximation is useful only within a limited range of a sufficiently concentrated two-component buffer mixture.     

Actinide heterobimetallic oxides (Th, U): reduction studies

In our laboratories we have been studying the synthesis and reactivity of binary actinide and lanthanide intermetallic compounds. In this work, the air-oxidation of ThCu₂ and AnNi₂ (An = Th, U) was followed by thermogravimetry (TG) and the products were characterized by X-ray powder diffraction (XRD). The heterobimetallic oxides obtained are described by the formulas 2MO·ThO₂ (M = Cu, Ni) and 2NiO·UO₃. The thermogravimetric analysis under hydrogen of these heterobimetallic oxides show one mass loss for 2MO·ThO₂ and two mass losses for 2NiO·UO₃ over a wide range of temperature (293–1273 K). The characterization by XRD shows that the reduction products are 2M·ThO₂ (M = Cu, Ni) and 2Ni·UO₂, with all the actinides in the 4+ oxidation state. The actinide heterobimetallic oxides were described as copper or nickel supported catalysts.     

Ionene–surfactant complexes: temperature and humidity sensitive materials

Solid stoichiometric complexes of [3,12]-ionene and dodecyl sulfate form upon reaction of the bromide of the ionene and the silver salt of dodecyl sulfate in methanol. IR, DSC, and TG investigations indicated that the solid complexes are stable between 30 and 120 °C. TG and DSC also showed that the complexes easily take up water at ambient conditions. These samples are optically isotropic. When exposed to an increased humidity they exhibit optical anisotropy, i.e., birefringence, which is caused by the formation of a hexagonal mesogenic phase. Mesogenicity is necessarily accompanied by a further uptake of water (4–5 H₂O molecules per ionic unit), which is dependent on the relative humidity. The phase behavior as a function of temperature and controlled relative humidity was studied using birefringence measurements and polarizing microscopy.     

Shear-induced sponge-to-lamellar phase transition studied by rheo-birefringence

We report on the shear induced transition from the L₃- to the L-phase studied by means of flow birefringence using the system pentaethyleneglycol monododecylether (C₁₂E₅), decane, water. The dependence of the critical shear rate, at which the transition from the isotropic state to the anisotropic takes place, on membrane volume fraction was studied in temperature ramp experiments at different constant shear rates and in isothermal shear ramp experiments. These results are compared with relaxation experiments from the shear aligned state back to the isotropic. For all these experiments power law exponents in the membrane volume fraction between 1.6 and 2.8 were found, which are rather low compared to values of current theories. The values found for the inverse critical shear rate and the decay times from the relaxation experiments differ by four orders of magnitude.