Estimation of precision and efficiency mass transfer steps for the determination of pesticides in vegetables aiming at the expression of results with reliable uncertainty

A 'bottom-up' approach for the expression of results obtained from analytical methods that include analytical steps with recovery inherently different from 100% [mass transfer steps (MTS): extraction, evaporation, clean-up procedures, digestion, etc.] is presented. The estimation of the combination of all MTS uncertainty involves the comparison of the experimental dispersion of replicated analyses of spiked samples with the estimation of the uncertainty obtained for the combination of all uncertainty sources except MTS ones ('incomplete' estimation). The estimation of MTS uncertainty by difference is performed after evaluating the statistical difference between the 'incomplete' estimation and the experimental dispersion (F-test). When the two estimations are statistically equivalent, the MTS uncertainty is considered to be negligible in relation to the other sources budget. The assumption of constancy of MTS performance within the analytical range is tested through single analyses at several concentration levels and is evaluated by the inclusion of the expected values at the intervals resulting from the combination of the MTS uncertainty estimation performed at one concentration level and the 'incomplete' estimation. The developed methodology can also be useful for method optimisation and validation and for the detection of small trends in results. The determination of pesticides in sweet peppers by GC-NPD was used to explore the above concepts.     

Chemometric interpretation of pesticide occurence in soil samples from an intensive horticulture area in north Portugal

An extensive monitoring programme of pesticides was carried out in soil samples from an intensive horticulture area in north of Portugal, putting into practice the needs for increased control of soil quality as far as organic pollution is concerned. The area under investigation was additionally defined as vulnerable to nitrates due to local soil and aquifer characteristics, which might be extended to pesticides contamination. Five sampling sites were selected and soils analysed at three depths in eight sampling campaigns, for the period of 2 years. A stepwise multivariate statistical approach was selected to uncover most relevant patterns inside a complex environmental data matrix. Cluster analysis was applied both to group pesticides and samples, giving a primary and unsupervised overlook of privileged relationships. Clusters of persistent pesticides and selected herbicides were identified, whereas sample classes were also formed and disposed geographically. Thirty eight percent of analysed soils samples fell into one class characterized by low contamination (class 1 in cluster analysis), which is entirely representative of the sampling site no. 1. Afterwards, linear discriminant analysis was applied to identify those pesticides, which had a higher impact in the definition of classes. Finally, factor analysis using a five component model was implemented in order to bring to light the constitution and data variance explained by each of the five main principal components, as well as, their relation to pest management practices. A factor was identified (PC1 – 22% variance) composed of chlorinated pesticides, which was representative of one of the investigated sites indicating its high contamination status. Qualitative main findings and class average concentration values were obtained through this multivariate statistical approach.     

A more convenient and general procedure for O-monobenzylation of diols via stannylenes: a critical reevaluation of the Bu2SnO method

A more consistent, straightforward, and economical protocol for generation of stannylene species and their reaction with BnBr leading to products of O-monobenzylation of diols has been set. It has shown to be specially indicated for substrates bearing vicinal trans 1,2-diol moieties on cyclohexane backbones, which are more resistant to these transformations. Such protocol has been successfully applied to myo-inositol derivatives and acyclic diols.     

A new production method for carrier-free201Tl using IEN'S cyclotron in Rio De Janeiro

A new and simplified method was developed for the separation of thallium 201 which will allow the shipment of a “one shot generator” to distant places and easy elution at the destination. Thallium is produced as usually, through the reaction $${}^{nat}Tl/p,xn/^{201} pb\xrightarrow{{\beta ^ + }}{}^{201}Tl$$ with 24-MeV protons from IEN'S CV-28 cyclotron. The separation is based on the properties of a chelating carboxylic acid cation exchange resin column which at pH 4.5 retains lead while thallim is easily eluted. This column can also be used as a regular generator to produced greater quantities of²⁰¹Tl but at the expense of more elutions.     

Determination of copper in medicinal plants used as dietary supplements by atomic absorption spectrometry with direct flame solid analysis

An alternative device for the direct solid analysis (DSA) for copper determination by flame atomic absorption spectrometry (FAAS) is proposed. Copper was directly determined in commercial medicinal plants used as dietary supplements. The determination of copper in solid samples by DSA–FAAS was made by using a conventional air–acetylene flame. Between 0.05 and 1.5 mg of each test, sample was weighed directly into a small polyethylene vial connected to the device used for solid introduction into the flame. Test samples were introduced into the flame as a dry aerosol using a T-quartz cell set between the burner and the optical path. The T-quartz cell has a slit in the superior part by which the solid aerosol passes to the flame. A transient signal, evaluated as integrated absorbance, is produced and it is totally integrated in 2 s. Background signals always presented absorbance values less than 0.1. It was found a characteristic mass of 0.8 ng Cu and absolute limit of detection of 1.2 ng (3 s), or 1.2 μg g⁻¹ if a sample mass of 1 mg was used. Optimized conditions for air flow rate, flame stoichiometry, and so on were established as well. No excessive grinding of the samples was needed and samples with particle of size less than 80 μm were used throughout. No statistical difference between the results from the proposed system and those obtained by sample digestion and determination by conventional FAAS was observed. With the proposed procedure, more than 50 test samples can be analyzed in 1 h and it can be easily adapted to conventional spectrometers for FAAS.     

预处理条件对Zn/Al-CLM的丙烷芳构化性能的影响

在脉冲微反装置上考察了不同的预处理条件对Zn/Al-CLM催化剂的丙烷芳构化反应的影响。结果表明，丙烷在Zn/Al-CLM催化剂上具有一定的的反应活性和芳烃选择性，而且芳构化主要转化为苯；载体Al-CLM的焙烧温度、金属锌负载量、活化温度等对Zn/Al-CLM催化剂的丙烷芳构化性能具有重要影响。载体经500℃预焙烧制备的Zn/Al-CLM催化剂具有最好的柱结构保留度，从而表现出最佳的芳构化性能；随着锌含量的增加，Zn/Al-CLM催化剂的酸量增大，从而使丙烷转化率增大，而选择性则是锌含量质量分数为5．8％时具有极大值；400℃活化处理可使Zn与Al-CLM之间具有适中的相互作用，从而使得Zn/Al-CLM具有较高的芳烃收率。     

Chemical synthesis and firefly luciferase produced dehydroluciferyl-coenzyme A

Dehydroluciferyl-coenzyme A (L-CoA) was chemically synthesized and characterized by MS, UV-vis spectrometry and RP-HPLC. The identity of the chemically synthesized compound with the one that was produced by firefly luciferase was confirmed. Moreover, the reversibility of the enzymatic conversion of dehydroluciferin ? dehydroluciferyl-adenylate ? L-CoA was also confirmed. The chemical synthesis of L-CoA, described here, may help the clarification of the activator effect of CoA on luciferase bioluminescent assays, in which the enzyme catalyzed formation of L-CoA and the consequent destruction of L-AMP is one of the possible explanations for that effect.     

Dynamics and energetics of the self-assembly of a hydrophobically modified polyelectrolyte: Naphthalene-labeled poly(acrylic acid)

Steady-state and time-resolved fluorescence studies were performed on aqueous solutions of poly(acrylic acid) hydrophobically modified with two very different levels of naphthalene (Np). It is demonstrated that unique information on association phenomena involving hydrophobe-modifed polymers can be obtained from an extended fluorescence study by using data for a less-modified polymer as a reference. For the more highly modified polymer, the presence of excited-state (as well as ground-state) dimers in addition to monomer emission due to locally excited naphthalene gives evidence for hydrophobic association between naphthalene groups. This association becomes, as expected, much less important at higher pH due to the electrostatic repulsion between different chain segments. However, it is noted that even at high pH there is a significant self-association. The coexistence of static and dynamic quenching phenomena of the Np monomer label was also revealed in the time-resolved fluorescence data. The data are compatible with the existence of two types of monomers and one excimer and suggest that the essential contribution to the monomer emission comes from isolated chromophores, whereas excimer formation arises from both a dynamic route (excited Np chromophores able to produce a dynamic excimer) and a static route (excitation of ground-state Np dimers). At room temperature, the dissociative reaction, excimer-to-monomer, can be neglected, and thus the rate constant for excimer formation and decay could be obtained with and without considering the influence of preformed dimers. Temperature has shown to induce different behavior in the polymer photophysics. In the case of the less-labeled polymer, the decays were found to be single-exponential with the fluorescence lifetime decreasing with increasing temperature. From the temperature dependence of the steady-state fluorescence data, the activation energy for excimer formation and the binding energy of the excimer were evaluated at different pH values, through the Stevens-Ban-type plots of the excimer-to-monomer intensity ratio. With the time-resolved data, measured in the temperature range of 5-60 degrees C, it was possible to extract the intrinsic activation energies for excimer formation. The thermodynamic driving force for the intrapolymeric association was found to be dependent on a balance between hydrophobic and electrostatic interactions, which are dependent on the pH, temperature, and hydrophobic content of the polymer.     

Lanthanide nitrate complexes with 2-azacyclononanone

Thermal behavior of rare earth nitrate complexes with 2-azacyclononanone (AZA) with Ln(NO₃)₃·3(AZA) composition (where Ln=Gd, Er and Ho) was analyzed in kinetic point of view. Kinetic parameters were calculated from thermogravimetric data. All obtained results were similar. The first decomposition step was representative to the loss of ligand and the residue was essentially Ln₂O₃. Furthermore, a reaction path was proposed for the thermal decomposition of the Ln(NO₃)₃·3(AZA).     

Thermodynamic properties of quinoxaline-1,4-dioxide derivatives: a combined experimental and computational study

The mean (N-O) bond dissociation enthalpies were derived for three 2-methyl-3-(R)-quinoxaline 1,4-dioxide (1) derivatives, with R = methyl (1a), ethoxycarbonyl (1b), and benzyl (1c). The standard molar enthalpies of formation in the gaseous state at T = 298.15 K for the three 1 derivatives were determined from the enthalpies of combustion of the crystalline solids and their enthalpies of sublimation. In parallel, accurate density functional theory-based calculations were carried out in order to estimate the gas-phase enthalpies of formation for the corresponding quinoxaline derivatives. Also, theoretical calculations were used to obtain the first and second N-O dissociation enthalpies. These dissociation enthalpies are in excellent agreement with the experimental results herewith reported.